Abstract: Security has been an important issue and concern in the
smart home systems. Smart home networks consist of a wide range of
wired or wireless devices, there is possibility that illegal access to
some restricted data or devices may happen. Password-based
authentication is widely used to identify authorize users, because this
method is cheap, easy and quite accurate. In this paper, a neural
network is trained to store the passwords instead of using verification
table. This method is useful in solving security problems that
happened in some authentication system. The conventional way to
train the network using Backpropagation (BPN) requires a long
training time. Hence, a faster training algorithm, Resilient
Backpropagation (RPROP) is embedded to the MLPs Neural
Network to accelerate the training process. For the Data Part, 200
sets of UserID and Passwords were created and encoded into binary
as the input. The simulation had been carried out to evaluate the
performance for different number of hidden neurons and combination
of transfer functions. Mean Square Error (MSE), training time and
number of epochs are used to determine the network performance.
From the results obtained, using Tansig and Purelin in hidden and
output layer and 250 hidden neurons gave the better performance. As
a result, a password-based user authentication system for smart home
by using neural network had been developed successfully.
Abstract: A generalization of the concepts of Feistel Networks (FN), known as Extended Feistel Network (EFN) is examined. EFN splits the input blocks into n > 2 sub-blocks. Like conventional FN, EFN consists of a series of rounds whereby at least one sub-block is subjected to an F function. The function plays a key role in the diffusion process due to its completeness property. It is also important to note that in EFN the F-function is the most computationally expensive operation in a round. The aim of this paper is to determine a suitable type of EFN for a scalable cipher. This is done by analyzing the threshold number of rounds for different types of EFN to achieve the completeness property as well as the number of F-function required in the network. The work focuses on EFN-Type I, Type II and Type III only. In the analysis it is found that EFN-Type II and Type III diffuses at the same rate and both are faster than Type-I EFN. Since EFN-Type-II uses less F functions as compared to EFN-Type III, therefore Type II is the most suitable EFN for use in a scalable cipher.
Abstract: The surface water used in this study was collected from the Chao Praya River at the lower part at the Nonthaburi bridge. It was collected and used throughout the experiment. TOC (also known as DOC) in the range between 2.5 to 5.6 mg/l were investigated in this experiment. The use of conventional treatment methods such as FeCl3 and PAC showed that TOC removal was 65% using FeCl3 and 78% using PAC (powder activated carbon). The advanced oxidation process alone showed only 35% removal of TOC. Coupling advanced oxidation with a small amount of PAC (0.05g/L) increased efficiency by upto 55%. The combined BAC with advanced oxidation process and small amount of PAC demonstrated the highest efficiency of up to 95% of TOC removal and lower sludge production compared with other methods.
Abstract: Wavelet neural networks (WNNs) have emerged as a vital alternative to the vastly studied multilayer perceptrons (MLPs) since its first implementation. In this paper, we applied various clustering algorithms, namely, K-means (KM), Fuzzy C-means (FCM), symmetry-based K-means (SBKM), symmetry-based Fuzzy C-means (SBFCM) and modified point symmetry-based K-means (MPKM) clustering algorithms in choosing the translation parameter of a WNN. These modified WNNs are further applied to the heterogeneous cancer classification using benchmark microarray data and were compared against the conventional WNN with random initialization method. Experimental results showed that a WNN classifier with the MPKM algorithm is more precise than the conventional WNN as well as the WNNs with other clustering algorithms.
Abstract: Knowledge of an organization does not merely reside
in structured form of information and data; it is also embedded in
unstructured form. The discovery of such knowledge is particularly
difficult as the characteristic is dynamic, scattered, massive and
multiplying at high speed. Conventional methods of managing
unstructured information are considered too resource demanding and
time consuming to cope with the rapid information growth.
In this paper, a Multi-faceted and Automatic Knowledge
Elicitation System (MAKES) is introduced for the purpose of
discovery and capture of organizational knowledge. A trial
implementation has been conducted in a public organization to
achieve the objective of decision capture and navigation from a
number of meeting minutes which are autonomously organized,
classified and presented in a multi-faceted taxonomy map in both
document and content level. Key concepts such as critical decision
made, key knowledge workers, knowledge flow and the relationship
among them are elicited and displayed in predefined knowledge
model and maps. Hence, the structured knowledge can be retained,
shared and reused.
Conducting Knowledge Management with MAKES reduces work
in searching and retrieving the target decision, saves a great deal of
time and manpower, and also enables an organization to keep pace
with the knowledge life cycle. This is particularly important when
the amount of unstructured information and data grows extremely
quickly. This system approach of knowledge management can
accelerate value extraction and creation cycles of organizations.
Abstract: This paper considers the control of the longitudinal
flight dynamics of an F-16 aircraft. The primary design objective
is model-following of the pitch rate q, which is the preferred
system for aircraft approach and landing. Regulation of the aircraft
velocity V (or the Mach-hold autopilot) is also considered, but
as a secondary objective. The problem is challenging because the
system is nonlinear, and also non-affine in the input. A sliding
mode controller is designed for the pitch rate, that exploits the
modal decomposition of the linearized dynamics into its short-period
and phugoid approximations. The inherent robustness of the SMC
design provides a convenient way to design controllers without gain
scheduling, with a steady-state response that is comparable to that
of a conventional polynomial based gain-scheduled approach with
integral control, but with improved transient performance. Integral
action is introduced in the sliding mode design using the recently
developed technique of “conditional integrators", and it is shown that
robust regulation is achieved with asymptotically constant exogenous
signals, without degrading the transient response. Through extensive
simulation on the nonlinear multiple-input multiple-output (MIMO)
longitudinal model of the F-16 aircraft, it is shown that the conditional
integrator design outperforms the one based on the conventional linear
control, without requiring any scheduling.
Abstract: Considering complexity of products, new geometrical
design and investment tolerances that are necessary, measuring and
dimensional controlling involve modern and more precise methods.
Photo digitizing method using two cameras to record pictures and
utilization of conventional method named “cloud points" and data
analysis by the use of ATOUS software, is known as modern and
efficient in mentioned context. In this paper, benefits of photo
digitizing method in evaluating sampling of machining processes
have been put forward. For example, assessment of geometrical
integrity surface in 5-axis milling process and measurement of
carbide tool wear in turning process, can be can be brought forward.
Advantages of this method comparing to conventional methods have
been expressed.
Abstract: This paper presents an improvement method of
the multiple pitch estimation algorithm using comb filters.
Conventionally the pitch was estimated by using parallel
-connected comb filters method (PCF). However, PCF has
problems which often fail in the pitch estimation when there is
the fundamental frequency of higher tone near harmonics of
lower tone. Therefore the estimation is assigned to a wrong
note when shared frequencies happen. This issue often occurs
in estimating octave 3 or more. Proposed method, for solving
the problem, estimates the pitch with every harmonic instead of
every octave. As a result, our method reaches the accuracy of
more than 80%.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: As a structure for processing string problem, suffix
array is certainly widely-known and extensively-studied. But if the
string access pattern follows the “90/10" rule, suffix array can not take
advantage of the fact that we often find something that we have just
found. Although the splay tree is an efficient data structure for small
documents when the access pattern follows the “90/10" rule, it
requires many structures and an excessive amount of pointer
manipulations for efficiently processing and searching large
documents. In this paper, we propose a new and conceptually powerful
data structure, called splay suffix arrays (SSA), for string search. This
data structure combines the features of splay tree and suffix arrays into
a new approach which is suitable to implementation on both
conventional and clustered computers.
Abstract: Fuzzy Load forecasting plays a paramount role in the operation and management of power systems. Accurate estimation of future power demands for various lead times facilitates the task of generating power reliably and economically. The forecasting of future loads for a relatively large lead time (months to few years) is studied here (long term load forecasting). Among the various techniques used in forecasting load, artificial intelligence techniques provide greater accuracy to the forecasts as compared to conventional techniques. Fuzzy Logic, a very robust artificial intelligent technique, is described in this paper to forecast load on long term basis. The paper gives a general algorithm to forecast long term load. The algorithm is an Extension of Short term load forecasting method to Long term load forecasting and concentrates not only on the forecast values of load but also on the errors incorporated into the forecast. Hence, by correcting the errors in the forecast, forecasts with very high accuracy have been achieved. The algorithm, in the paper, is demonstrated with the help of data collected for residential sector (LT2 (a) type load: Domestic consumers). Load, is determined for three consecutive years (from April-06 to March-09) in order to demonstrate the efficiency of the algorithm and to forecast for the next two years (from April-09 to March-11).
Abstract: Power system stabilizers (PSS) are now routinely used in the industry to damp out power system oscillations. In this paper, particle swarm optimization (PSO) technique is applied to design a robust power system stabilizer (PSS). The design problem of the proposed controller is formulated as an optimization problem and PSO is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The non-linear simulation results are presented under wide range of operating conditions; disturbances at different locations as well as for various fault clearing sequences to show the effectiveness and robustness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. Further, all the simulations results are compared with a conventionally designed power system stabilizer to show the superiority of the proposed design approach.
Abstract: In recent years Operational Transconductance Amplifier based high frequency integrated circuits, filters and systems have been widely investigated. The usefulness of OTAs over conventional OP-Amps in the design of both first order and second order active filters are well documented. This paper discusses some of the tunability issues using the Matlab/Simulink® software which are previously unreported for any commercial OTA. Using the simulation results two first order voltage controlled all pass filters with phase tuning capability are proposed.
Abstract: In conventional seedling production, the seedlings are
being grown in the open field under natural conditions. Here they are
susceptible to sudden changes in climate were their quality and yield
is affected. Quality seedlings are essential for good growth and
performance of crops in main field; they serve as a foundation for the
economic returns to the farmer. Producing quality seedling demands
usage of hybrid seeds as they have the ability to result in better yield,
greater uniformity, improved color, disease resistance, and so forth.
Hybrid seed production poses major operational challenge and its
seed use efficiency plays an important role. Thus in order to
overcome the difficulties currently present in conventional seedling
production and to efficiently use hybrid seeds, ITC Limited Agri
Business Divisions - Sustainability Cell as conceptualized a novel
method of seedling production unit for farmers in West Godavari
District of Andhra Pradesh. The “Green House based Float Seedling"
methodology aims at a protected cultivation technique wherein the
micro climate surrounding the plant/seedling body is controlled
partially or fully as per the requirement of the species. This paper
reports on the techno economic evaluation of green house for
cultivation of float based seedling production with experimental
results that was attained from the pilot implementation in West
Godavari District, Rajahmundry region of India.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: Renewable energy resources are inexhaustible, clean as compared with conventional resources. Also, it is used to supply regions with no grid, no telephone lines, and often with difficult accessibility by common transport. Satellite earth stations which located in remote areas are the most important application of renewable energy. Neural control is a branch of the general field of intelligent control, which is based on the concept of artificial intelligence. This paper presents the mathematical modeling of satellite earth station power system which is required for simulating the system.Aswan is selected to be the site under consideration because it is a rich region with solar energy. The complete power system is simulated using MATLAB–SIMULINK.An artificial neural network (ANN) based model has been developed for the optimum operation of earth station power system. An ANN is trained using a back propagation with Levenberg–Marquardt algorithm. The best validation performance is obtained for minimum mean square error. The regression between the network output and the corresponding target is equal to 96% which means a high accuracy. Neural network controller architecture gives satisfactory results with small number of neurons, hence better in terms of memory and time are required for NNC implementation. The results indicate that the proposed control unit using ANN can be successfully used for controlling the satellite earth station power system.
Abstract: In this paper, a frequency-variation based method has
been proposed for transistor parameter estimation in a commonemitter
transistor amplifier circuit. We design an algorithm to estimate
the transistor parameters, based on noisy measurements of the output
voltage when the input voltage is a sine wave of variable frequency
and constant amplitude. The common emitter amplifier circuit has
been modelled using the transistor Ebers-Moll equations and the
perturbation technique has been used for separating the linear and
nonlinear parts of the Ebers-Moll equations. This model of the amplifier
has been used to determine the amplitude of the output sinusoid as
a function of the frequency and the parameter vector. Then, applying
the proposed method to the frequency components, the transistor
parameters have been estimated. As compared to the conventional
time-domain least squares method, the proposed method requires
much less data storage and it results in more accurate parameter
estimation, as it exploits the information in the time and frequency
domain, simultaneously. The proposed method can be utilized for
parameter estimation of an analog device in its operating range of
frequencies, as it uses data collected from different frequencies output
signals for parameter estimation.
Abstract: A compact 1x3 power splitter based on Photonic
Crystal Waveguides (PCW) with flexible power splitting ratio is
presented in this paper. Multimode interference coupler (MMI) is
integrated with PCW. The device size reduction compared with the
conventional MMI power splitter is attributed to the large dispersion
of the PCW. Band Solve tool is used to calculate the band structure of
PCW. Finite Difference Time Domain (FDTD) method is adopted to
simulate the relevant structure at 1550nm wavelength. The device is
polarization insensitive and allows the control of output (o/p) powers
within certain percentage points for both polarizations.
Abstract: High Strength Concrete (HSC) is defined as concrete
that meets special combination of performance and uniformity
requirements that cannot be achieved routinely using conventional
constituents and normal mixing, placing, and curing procedures. It is
a highly complex material, which makes modeling its behavior a very
difficult task. This paper aimed to show possible applicability of
Neural Networks (NN) to predict the slump in High Strength
Concrete (HSC). Neural Network models is constructed, trained and
tested using the available test data of 349 different concrete mix
designs of High Strength Concrete (HSC) gathered from a particular
Ready Mix Concrete (RMC) batching plant. The most versatile
Neural Network model is selected to predict the slump in concrete.
The data used in the Neural Network models are arranged in a format
of eight input parameters that cover the Cement, Fly Ash, Sand,
Coarse Aggregate (10 mm), Coarse Aggregate (20 mm), Water,
Super-Plasticizer and Water/Binder ratio. Furthermore, to test the
accuracy for predicting slump in concrete, the final selected model is
further used to test the data of 40 different concrete mix designs of
High Strength Concrete (HSC) taken from the other batching plant.
The results are compared on the basis of error function (or
performance function).
Abstract: Recent developments in Soft computing techniques,
power electronic switches and low-cost computational hardware have
made it possible to design and implement sophisticated control
strategies for sensorless speed control of AC motor drives. Such an
attempt has been made in this work, for Sensorless Speed Control of
Induction Motor (IM) by means of Direct Torque Fuzzy Control
(DTFC), PI-type fuzzy speed regulator and MRAS speed estimator
strategy, which is absolutely nonlinear in its nature. Direct torque
control is known to produce quick and robust response in AC drive
system. However, during steady state, torque, flux and current ripple
occurs. So, the performance of conventional DTC with PI speed
regulator can be improved by implementing fuzzy logic techniques.
Certain important issues in design including the space vector
modulated (SVM) 3-Ф voltage source inverter, DTFC design,
generation of reference torque using PI-type fuzzy speed regulator
and sensor less speed estimator have been resolved. The proposed
scheme is validated through extensive numerical simulations on
MATLAB. The simulated results indicate the sensor less speed
control of IM with DTFC and PI-type fuzzy speed regulator provides
satisfactory high dynamic and static performance compare to
conventional DTC with PI speed regulator.