Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: This paper describes an efficient hardware implementation of a new technique for interfacing the data exchange between the microprocessor-based systems and the external devices. This technique, based on the use of software/hardware system and a reduced physical address, enlarges the interfacing capacity of the microprocessor-based systems, uses the Direct Memory Access (DMA) to increases the frequency of the new bus, and improves the speed of data exchange. While using this architecture in microprocessor-based system or in computer, the input of the hardware part of our system will be connected to the bus system, and the output, which is a new bus, will be connected to an external device. The new bus is composed of a data bus, a control bus and an address bus. A Xilinx Integrated Software Environment (ISE) 7.1i has been used for the programmable logic implementation.
Abstract: In this work, thermoelastic damping effect on the hemi- spherical shells is investigated. The material is selected silicon, and heat conduction equation for thermal flow is solved to obtain the temperature profile in which bending approximation with inextensional assumption of the model. Using the temperature profile, eigen-value analysis is performed to get the natural frequencies of hemispherical shells. Effects of mode numbers, radii and radial thicknesses of the model on the natural frequencies are analyzed in detail. Furthermore, the quality factor (Q-factor) is defined, and discussed for the ring and hemispherical shell.
Abstract: In this paper the development of a heat exchanger as a
pilot plant for educational purpose is discussed and the use of neural
network for controlling the process is being presented. The aim of the
study is to highlight the need of a specific Pseudo Random Binary
Sequence (PRBS) to excite a process under control. As the neural
network is a data driven technique, the method for data generation
plays an important role. In light of this a careful experimentation
procedure for data generation was crucial task. Heat exchange is a
complex process, which has a capacity and a time lag as process
elements. The proposed system is a typical pipe-in- pipe type heat
exchanger. The complexity of the system demands careful selection,
proper installation and commissioning. The temperature, flow, and
pressure sensors play a vital role in the control performance. The
final control element used is a pneumatically operated control valve.
While carrying out the experimentation on heat exchanger a welldrafted
procedure is followed giving utmost attention towards safety
of the system. The results obtained are encouraging and revealing
the fact that if the process details are known completely as far as
process parameters are concerned and utilities are well stabilized then
feedback systems are suitable, whereas neural network control
paradigm is useful for the processes with nonlinearity and less
knowledge about process. The implementation of NN control
reinforces the concepts of process control and NN control paradigm.
The result also underlined the importance of excitation signal
typically for that process. Data acquisition, processing, and
presentation in a typical format are the most important parameters
while validating the results.
Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.
Abstract: Bidding is a very important business function to find
latent contractors of construction projects. Moreover, bid markup is
one of the most important decisions for a bidder to gain a reasonable
profit. Since the bidding system is a complex adaptive system, bidding
agent need a learning process to get more valuable knowledge for a bid,
especially from past public bidding information. In this paper, we
proposed an iterative agent leaning model for bidders to make markup
decisions. A classifier for public bidding information named PIBS is
developed to make full use of history data for classifying new bidding
information. The simulation and experimental study is performed to
show the validity of the proposed classifier. Some factors that affect
the validity of PIBS are also analyzed at the end of this work.
Abstract: Dense slurry flow through centrifugal pump casing
has been modeled using the Eulerian-Eulerian approach with
Eulerian multiphase model in FLUENT 6.1®. First order upwinding
is considered for the discretization of momentum, k and ε terms.
SIMPLE algorithm has been applied for dealing with pressurevelocity
coupling. A mixture property based k-ε turbulence model
has been used for modeling turbulence. Results are validated first
against mesh independence and experiments for a particular set of
operational and geometric conditions. Parametric analysis is then
performed to determine the effect on important physical quantities
viz. solid velocities, solid concentration and solid stresses near the
wall with various operational geometric conditions of the pump.
Abstract: Understanding proteins functions is a major goal in
the post-genomic era. Proteins usually work in context of other
proteins and rarely function alone. Therefore, it is highly relevant to
study the interaction partners of a protein in order to understand its
function. Machine learning techniques have been widely applied to
predict protein-protein interactions. Kernel functions play an
important role for a successful machine learning technique. Choosing
the appropriate kernel function can lead to a better accuracy in a
binary classifier such as the support vector machines. In this paper,
we describe a Bayesian kernel for the support vector machine to
predict protein-protein interactions. The use of Bayesian kernel can
improve the classifier performance by incorporating the probability
characteristic of the available experimental protein-protein
interactions data that were compiled from different sources. In
addition, the probabilistic output from the Bayesian kernel can assist
biologists to conduct more research on the highly predicted
interactions. The results show that the accuracy of the classifier has
been improved using the Bayesian kernel compared to the standard
SVM kernels. These results imply that protein-protein interaction can
be predicted using Bayesian kernel with better accuracy compared to
the standard SVM kernels.
Abstract: Graphene-metal contact resistance limits the performance of graphene-based electrical devices. In this work, we have fabricated both graphene field-effect transistors (GFET) and transfer length measurement (TLM) test devices with titanium contacts. The purpose of this work is to compare the contact resistances that can be numerically extracted from the GFETs and measured from the TLM structures. We also provide a brief review of the work done in the field to solve the contact resistance problem.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.
Abstract: Wheeled Mobile Robots (WMRs) are built with their
Wheels- drive machine, Motors. Depend on their desire design of
WMR, Technicians made used of DC Motors for motion control. In
this paper, the author would like to analyze how to choose DC motor
to be balance with their applications of especially for WMR.
Specification of DC Motor that can be used with desire WMR is to
be determined by using MATLAB Simulink model. Therefore, this
paper is mainly focus on software application of MATLAB and
Control Technology. As the driving system of DC motor, a
Peripheral Interface Controller (PIC) based control system is
designed including the assembly software technology and H-bridge
control circuit. This Driving system is used to drive two DC gear
motors which are used to control the motion of WMR. In this
analyzing process, the author mainly focus the drive system on
driving two DC gear motors that will control with Differential Drive
technique to the Wheeled Mobile Robot . For the design analysis of
Motor Driving System, PIC16F84A is used and five inputs of sensors
detected data are tested with five ON/OFF switches. The outputs of
PIC are the commands to drive two DC gear motors, inputs of Hbridge
circuit .In this paper, Control techniques of PIC
microcontroller and H-bridge circuit, Mechanism assignments of
WMR are combined and analyzed by mainly focusing with the
“Modeling and Simulink of DC Motor using MATLAB".
Abstract: The paper shows that in the analysis of a queuing system with fixed-size batch arrivals, there emerges a set of polynomials which are a generalization of Chebyshev polynomials of the second kind. The paper uses these polynomials in assessing the transient behaviour of the overflow (equivalently call blocking) probability in the system. A key figure to note is the proportion of the overflow (or blocking) probability resident in the transient component, which is shown in the results to be more significant at the beginning of the transient and naturally decays to zero in the limit of large t. The results also show that the significance of transients is more pronounced in cases of lighter loads, but lasts longer for heavier loads.
Abstract: A new approach for timestamp ordering problem in
serializable schedules is presented. Since the number of users using
databases is increasing rapidly, the accuracy and needing high
throughput are main topics in database area. Strict 2PL does not
allow all possible serializable schedules and so does not result high
throughput. The main advantages of the approach are the ability to
enforce the execution of transaction to be recoverable and the high
achievable performance of concurrent execution in central databases.
Comparing to Strict 2PL, the general structure of the algorithm is
simple, free deadlock, and allows executing all possible serializable
schedules which results high throughput. Various examples which
include different orders of database operations are discussed.
Abstract: One of the most common practices for strengthening
the reinforced concrete structures is the application of FRP (Fiber
Reinforce Plastic) sheets to increase the flexural and shear strengths
of the member. The elastic modulus of FRP is considerably higher
than that of concrete. This will result in debonding between the FRP
sheets and concrete surface. With conventional surface preparation of
concrete, the ultimate capacity of the FRP sheets can hardly be
achieved. New methods for preparation of the bonding surface have
shown improvements in reducing the premature debonding of FRP
sheets from concrete surface. The present experimental study focuses
on the application of grooving method to postpone debonding of the
FRP sheets attached to the side faces of concrete beams for shear
strengthening. Comparison has also been made with conventional
surface preparation method. This study clearly shows the efficiency
of grooving method compared to surface preparation method, in
preventing the debonding phenomenon and in increasing the load
carrying capacity of FRP.
Abstract: The modern Kazakh society is characterized by strengthen cross-cultural communication, the emergence of new powerful subcultures, accelerated change in social systems and values. The socio-political reforms in all fields have changed the quality of social relationships and spiritual life.Cross-cultural approach involves the analysis of different types of behavior and communication, including the manifestation of the conflict, and the formation of marginal destructive stereotypes.
Abstract: Fast forecasting of stock market prices is very important for
strategic planning. In this paper, a new approach for fast forecasting of
stock market prices is presented. Such algorithm uses new high speed
time delay neural networks (HSTDNNs). The operation of these
networks relies on performing cross correlation in the frequency
domain between the input data and the input weights of neural
networks. It is proved mathematically and practically that the number
of computation steps required for the presented HSTDNNs is less
than that needed by traditional time delay neural networks
(TTDNNs). Simulation results using MATLAB confirm the
theoretical computations.
Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: We consider optimal channel equalization for MIMO
(multi-input/multi-output) time-varying channels in the sense of
MMSE (minimum mean-squared-error), where the observation noise
can be non-stationary. We show that all ZF (zero-forcing) receivers
can be parameterized in an affine form which eliminates completely
the ISI (inter-symbol-interference), and optimal channel equalizers
can be designed through minimization of the MSE (mean-squarederror)
between the detected signals and the transmitted signals,
among all ZF receivers. We demonstrate that the optimal channel
equalizer is a modified Kalman filter, and show that under the AWGN
(additive white Gaussian noise) assumption, the proposed optimal
channel equalizer minimizes the BER (bit error rate) among all
possible ZF receivers. Our results are applicable to optimal channel
equalization for DWMT (discrete wavelet multitone), multirate transmultiplexers,
OFDM (orthogonal frequency division multiplexing),
and DS (direct sequence) CDMA (code division multiple access)
wireless data communication systems. A design algorithm for optimal
channel equalization is developed, and several simulation examples
are worked out to illustrate the proposed design algorithm.
Abstract: The hospital and the health-care center of a
community, as a place for people-s life-care and health-care settings,
must provide more and better services for patients or residents. After
Establishing Electronic Medical Record (EMR) system -which is a
necessity- in the hospital, providing pervasive services is a further
step. Our objective in this paper is to use pervasive computing in a
case study of healthcare, based on EMR database that coordinates
application services over network to form a service environment for
medical and health-care. Our method also categorizes the hospital
spaces into 3 spaces: Public spaces, Private spaces and Isolated
spaces. Although, there are many projects about using pervasive
computing in healthcare, but all of them concentrate on the disease
recognition, designing smart cloths, or provide services only for
patient. The proposed method is implemented in a hospital. The
obtained results show that it is suitable for our purpose.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.