Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: To determine if the murine insulinoma, β-TC-6, is a
suitable substitute for primary pancreatic β-cells in the study of β-
cell functional heterogeneity, we used three distinct functional assays
to ascertain the cell line-s response to glucose or a glucose analog.
These assays include: (i) a 2-NBDG uptake assay; (ii) a calcium
influx assay, and; (iii) a quinacrine secretion assay. We show that a
population of β-TC-6 cells endocytoses the glucose analog, 2-
NBDG, at different rates, has non-uniform intracellular calcium ion
concentrations and releases quinacrine at different rates when
challenged with glucose. We also measured the Km for β-TC-6
glucose uptake to be 46.9 mM and the Vm to be 8.36 x 10-5
mmole/million cells/min. These data suggest that β-TC-6 might be
used as an alternative to primary pancreatic β-cells for the study of
glucose-dependent β-cell functional heterogeneity.
Abstract: In this paper, the deformation modes of a compact impact absorption member subjected to axial compression are investigated using finite element method and experiments. A multiple combination compact impact absorption member, referred to as a 'compress-expand member', is proposed to substitute the conventional thin-walled circular tube. This study found that the proposed compact impact absorption member has stable load increase characteristics and a wider range of high load efficiency (Pave/Pmax) than the thin-walled circular tube. Moreover, the proposed compact impact absorption member can absorb larger loads in a smaller radius than the thin-walled cylindrical tube, as it can maintain its stable deformation in increased wall thicknesses.
Abstract: A typical definition of the Computer Aided Diagnosis
(CAD), found in literature, can be: A diagnosis made by a radiologist
using the output of a computerized scheme for automated image
analysis as a diagnostic aid. Often it is possible to find the expression
Computer Aided Detection (CAD or CADe): this definition
emphasizes the intent of CAD to support rather than substitute the
human observer in the analysis of radiographic images. In this article
we will illustrate the application of CAD systems and the aim of
these definitions.
Commercially available CAD systems use computerized
algorithms for identifying suspicious regions of interest. In this paper
are described the general CAD systems as an expert system
constituted of the following components: segmentation / detection,
feature extraction, and classification / decision making.
As example, in this work is shown the realization of a Computer-
Aided Detection system that is able to assist the radiologist in
identifying types of mammary tumor lesions. Furthermore this
prototype of station uses a GRID configuration to work on a large
distributed database of digitized mammographic images.
Abstract: This paper presents a speed fuzzy sliding mode
controller for a vector controlled induction machine (IM) fed by a
voltage source inverter (PWM).
The sliding mode based fuzzy control method is developed to
achieve fast response, a best disturbance rejection and to maintain a
good decoupling.
The problem with sliding mode control is that there is high
frequency switching around the sliding mode surface. The FSMC is
the combination of the robustness of Sliding Mode Control (SMC)
and the smoothness of Fuzzy Logic (FL). To reduce the torque
fluctuations (chattering), the sign function used in the conventional
SMC is substituted with a fuzzy logic algorithm.
The proposed algorithm was simulated by Matlab/Simulink
software and simulation results show that the performance of the
control scheme is robust and the chattering problem is solved.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: The effect of seed inoculation by VA- mycorrhiza and
different levels of phosphorus fertilizer on growth and yield of
sunflower (Azargol cultivar) was studied in experiment farm of
Islamic Azad University, Karaj Branch during 2008 growing season.
The experiment treatments were arranged in factorial based on a
complete randomized block design with three replications. Four
phosphorus fertilizer levels of 25%, 50% 75% and 100% P
recommended with two levels of Mycorrhiza: with and without
Mycorrhiza (control) were assigned in a factorial combination.
Results showed that head diameter, number of seeds in head, seed
yield and oil yield were significantly higher in inoculated plants than
in non-inoculated plants. Head diameter, number of seeds in head,
1000 seeds weight, biological yield, seed yield and oil yield increased
with increasing P level above 75% P recommended in non-inoculated
plants, whereas no significant difference was observed between 75%
and 100% P recommended. The positive effect of mycorrhizal
inoculation decreased with increasing P levels due to decreased
percent root colonization at higher P levels. According to the results
of this experiment, application of mycorrhiza in present of 50% P
recommended had an appropriate performance and could increase
seed yield and oil production to an acceptable level, so it could be
considered as a suitable substitute for chemical phosphorus fertilizer
in organic agricultural systems.
Abstract: This paper presents a model for the characterization
and selection of beeswaxes for use as base substitute tissue for the
manufacture of objects suitable for external radiotherapy using
megavoltage photon beams. The model of characterization was
divided into three distinct stages: 1) verification of aspects related to
the origin of the beeswax, the bee species, the flora in the vicinity of
the beehives and procedures to detect adulterations; 2) evaluation of
physical and chemical properties; and 3) evaluation of beam
attenuation capacity. The chemical composition of the beeswax
evaluated in this study was similar to other simulators commonly
used in radiotherapy. The behavior of the mass attenuation coefficient
in the radiotherapy energy range was comparable to other simulators.
The proposed model is efficient and enables convenient assessment
of the use of any particular beeswax as a base substitute tissue for
radiotherapy.
Abstract: Tourism industry is an important sector in Malaysia economy and this motivates the examination of long-run relationships between tourist arrivals from three selected European countries in Malaysia and four possible determinants; relative prices, exchange rates, transportation cost and relative prices of substitute destination. The study utilizes data from January 1999 to September 2008 and employs standard econometric techniques that include unit root test and cointegration test. The estimated demand model indicates that depreciation of local currency and increases in prices at substitute destination have positive impact on tourist arrivals while increase in transportation cost has negative impact on tourist arrivals. In addition, the model suggests that higher rate of increase in local prices relative to prices at tourist country of origin may not deter tourists from coming to Malaysia
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: The coverage probability and range of IEEE 802.16
systems depend on different wireless scenarios. Evaluating the
performance of IEEE 802.16 systems over Stanford University
Interim (SUI) channels is suggested by IEEE 802.16 specifications.
In order to derive an effective method for forecasting the coverage
probability and range, this study uses the SUI channel model to
analyze the coverage probability with Rayleigh fading for an IEEE
802.16 system. The BER of the IEEE 802.16 system is shown in the
simulation results. Then, the maximum allowed path loss can be
calculated and substituted into the coverage analysis. Therefore,
simulation results show the coverage range with and without
Rayleigh fading.
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: In this paper, we consider the problem of tracking
multiple maneuvering targets using switching multiple target motion
models. With this paper, we aim to contribute in solving the problem
of model-based body motion estimation by using data coming from
visual sensors. The Interacting Multiple Model (IMM) algorithm is
specially designed to track accurately targets whose state and/or
measurement (assumed to be linear) models changes during motion
transition. However, when these models are nonlinear, the IMM
algorithm must be modified in order to guarantee an accurate track.
In this paper we propose to avoid the Extended Kalman filter because
of its limitations and substitute it with the Unscented Kalman filter
which seems to be more efficient especially according to the
simulation results obtained with the nonlinear IMM algorithm (IMMUKF).
To resolve the problem of data association, the JPDA
approach is combined with the IMM-UKF algorithm, the derived
algorithm is noted JPDA-IMM-UKF.
Abstract: Cluster analysis is the name given to a diverse collection of techniques that can be used to classify objects (e.g. individuals, quadrats, species etc). While Kohonen's Self-Organizing Feature Map (SOFM) or Self-Organizing Map (SOM) networks have been successfully applied as a classification tool to various problem domains, including speech recognition, image data compression, image or character recognition, robot control and medical diagnosis, its potential as a robust substitute for clustering analysis remains relatively unresearched. SOM networks combine competitive learning with dimensionality reduction by smoothing the clusters with respect to an a priori grid and provide a powerful tool for data visualization. In this paper, SOM is used for creating a toroidal mapping of two-dimensional lattice to perform cluster analysis on results of a chemical analysis of wines produced in the same region in Italy but derived from three different cultivators, referred to as the “wine recognition data" located in the University of California-Irvine database. The results are encouraging and it is believed that SOM would make an appealing and powerful decision-support system tool for clustering tasks and for data visualization.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.
Abstract: The main aim of this research is to study the possible
use of recycled fine aggregate made from waste rubble wall to
substitute partially for the natural sand used in the production of
cement and sand bricks. The bricks specimens were prepared by
using 100% natural sand; they were then replaced by recycled fine
aggregate at 25, 50, 75, and 100% by weight of natural sand. A series
of tests was carried out to study the effect of using recycled aggregate
on the physical and mechanical properties of bricks, such as density,
drying shrinkage, water absorption characteristic, compressive and
flexural strength. Test results indicate that it is possible to
manufacture bricks containing recycled fine aggregate with good
characteristics that are similar in physical and mechanical properties
to those of bricks with natural aggregate, provided that the percentage
of recycled fine aggregates is limited up to 50-75%.
Abstract: In our modern world, more physical transactions are being substituted by electronic transactions (i.e. banking, shopping, and payments), many businesses and companies are performing most of their operations through the internet. Instead of having a physical commerce, internet visitors are now adapting to electronic commerce (e-Commerce). The ability of web users to reach products worldwide can be greatly benefited by creating friendly and personalized online business portals. Internet visitors will return to a particular website when they can find the information they need or want easily. Dealing with this human conceptualization brings the incorporation of Artificial/Computational Intelligence techniques in the creation of customized portals. From these techniques, Fuzzy-Set technologies can make many useful contributions to the development of such a human-centered endeavor as e-Commerce. The main objective of this paper is the implementation of a Paradigm for the Intelligent Design and Operation of Human-Computer interfaces. In particular, the paradigm is quite appropriate for the intelligent design and operation of software modules that display information (such Web Pages, graphic user interfaces GUIs, Multimedia modules) on a computer screen. The human conceptualization of the user personal information is analyzed throughout a Cascaded Fuzzy Inference (decision-making) System to generate the User Ascribe Qualities, which identify the user and that can be used to customize portals with proper Web links.