Abstract: Fossil fuels are the major source to meet the world
energy requirements but its rapidly diminishing rate and adverse
effects on our ecological system are of major concern. Renewable
energy utilization is the need of time to meet the future challenges.
Ocean energy is the one of these promising energy resources. Threefourths
of the earth-s surface is covered by the oceans. This enormous
energy resource is contained in the oceans- waters, the air above the
oceans, and the land beneath them. The renewable energy source of
ocean mainly is contained in waves, ocean current and offshore solar
energy. Very fewer efforts have been made to harness this reliable
and predictable resource. Harnessing of ocean energy needs detail
knowledge of underlying mathematical governing equation and their
analysis. With the advent of extra ordinary computational resources
it is now possible to predict the wave climatology in lab simulation.
Several techniques have been developed mostly stem from numerical
analysis of Navier Stokes equations. This paper presents a brief over
view of such mathematical model and tools to understand and
analyze the wave climatology. Models of 1st, 2nd and 3rd generations
have been developed to estimate the wave characteristics to assess the
power potential. A brief overview of available wave energy
technologies is also given. A novel concept of on-shore wave energy
extraction method is also presented at the end. The concept is based
upon total energy conservation, where energy of wave is transferred
to the flexible converter to increase its kinetic energy. Squeezing
action by the external pressure on the converter body results in
increase velocities at discharge section. High velocity head then can
be used for energy storage or for direct utility of power generation.
This converter utilizes the both potential and kinetic energy of the
waves and designed for on-shore or near-shore application. Increased
wave height at the shore due to shoaling effects increases the
potential energy of the waves which is converted to renewable
energy. This approach will result in economic wave energy
converter due to near shore installation and more dense waves due to
shoaling. Method will be more efficient because of tapping both
potential and kinetic energy of the waves.
Abstract: A theoretical approach to radiation damage evolution
is developed. Stable temporal behavior taking place in solids under
irradiation are examined as phenomena of self-organization in nonequilibrium
systems.
Experimental effects of temporal self-organization in solids under
irradiation are reviewed. Their essential common properties and
features are highlighted and analyzed.
Dynamical model to describe development of self-oscillation of
density of point defects under stationary irradiation is proposed. The
emphasis is the nonlinear couplings between rate of annealing and
density of defects that determine the kind and parameters of an
arising self-oscillation.
The field of parameters (defect generation rate and environment
temperature) at which self-oscillations develop is found. Bifurcation
curve and self-oscillation period near it is obtained.
Abstract: This paper deals with the design of a moving sliding
surface in a variable structure plant for a second order system. The
chattering phenomena is also dealt with during the switching process
for an unstable sliding surface condition. The simulation examples
considered in this paper shows the effectiveness of the sliding mode
control method used for the design of the moving sliding surfaces. A
simulink model of the continuous system was also developed in
MATLAB-SIMULINK for the design and hence demonstrated. The
phase portraits and the state plots shows the demonstration of
the powerful control technique which can be applied for second
order systems.
Abstract: Three dimensional nanostructure materials have attracted the attention of many researches because the possibility to apply them for near future devices in sensors, catalysis and energy related. Tin dioxide is the most used material for gas sensing because its three-dimensional nanostructures and properties are related to the large surface exposed to gas adsorption. We propose the use of branch SnO2 nanowhiskers in interaction with ethanol. All Sn atoms are symmetric. The total energy, potential energy and Kinetic energy calculated for interaction between SnO2 and ethanol in different distances and temperatures. The calculations achieved by methods of Langevin Dynamic and Mont Carlo simulation. The total energy increased with addition ethanol molecules and temperature so interactions between them are endothermic.
Abstract: In order to meet environmental norms, Indian fuel
policy aims at producing ultra low sulphur diesel (ULSD) in near
future. A catalyst for meeting such requirements has been developed
and kinetics of this catalytic process is being looked into. In the
present investigations, effect of mass transfer on kinetics of ultra deep
hydrodesulphurization (UDHDS) to produce ULSD has been studied
to determine intrinsic kinetics over a pre-sulphided catalyst.
Experiments have been carried out in a continuous flow micro reactor
operated in the temperature range of 330 to 3600C, whsv of 1 hr-1 at a
pressure of 35 bar, and its parameters estimated. Based on the derived
rate expression and estimated parameters optimum operation range
has been determined for this UDHDS catalyst to obtain ULSD
product.
Abstract: Chloride induced corrosion of steel reinforcement is
the main cause of deterioration of reinforced concrete marine
structures. This paper investigates the relative performance of
alternative repair options with respect to the deterioration of
reinforced concrete bridge elements in marine environments. Focus is
placed on the initiation phase of reinforcement corrosion. A
laboratory study is described which involved exposing concrete
samples to accelerated chloride-ion ingress. The study examined the
relative efficiencies of two repair methods, namely Ordinary Portland
Cement (OPC) concrete and a concrete which utilised Ground
Granulated Blastfurnace Cement (GGBS) as a partial cement
replacement. The mix designs and materials utilised were identical to
those implemented in the repair of a marine bridge on the South East
coast of Ireland in 2007. The results of this testing regime serve to
inform input variables employed in probabilistic modelling of
deterioration for subsequent reliability based analysis to compare the
relative performance of the studied repair options.
Abstract: A new technique of topological multi-scale analysis is
introduced. By performing a clustering recursively to build a
hierarchy, and analyzing the co-scale and intra-scale similarities, an
Iterated Function System can be extracted from any data set. The study
of fractals shows that this method is efficient to extract
self-similarities, and can find elegant solutions the inverse problem of
building fractals. The theoretical aspects and practical
implementations are discussed, together with examples of analyses of
simple fractals.
Abstract: The argument that self-disclosure will change the
psychoanalytic process into a socio-cultural niche distorting the
therapeutic alliance and compromise therapeutic effectiveness is still
the widely held belief amongst many psychotherapists. This paper
considers the issues surrounding culture, disclosure and concealment
since they remain largely untheorized and clinically problematic. The
first part of the paper will critically examine the theory and practice
of psychoanalysis across cultures, and explore the reasons for
culturally diverse patients to conceal rather than disclose their
feelings and thoughts in the transference. This is followed by a
discussion on how immigrant analysts- anonymity is difficult to
maintain since diverse nationalities, language and accents provide
clues to the therapist-s and patient-s origins. Through personal
clinical examples of one the author-s (who is an immigrant) the paper
analyses the transference-countertransference paradigm and how it
reflects in the analyst-s self-revelation.
Abstract: This study endeavors to evaluate the effects of farmers’ training program on the adoption of improved farming practices, the output of rice farming, and the income as well as the profit from rice farming by employing an ex-post non-experimental data in Sierra Leone. It was established that participating in farmers’ training program increased the possibility of adoption of the improved farming activities that were implemented in the study area. Through the training program also, the proceeds from rice production was also established to have increased considerably. These results were in line with the assumption that one of the main constraints on the growth in agricultural output particularly rice cultivation in most African states is the lack of efficient extension programs.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible non-isothermal multicomponent
fluid mixture flow in a pipe. The set of the mass,
momentum and enthalpy conservation equations for gas phase is
solved in the model. Thermo-physical properties of multi-component
gas mixture are calculated by solving the Equation of State (EOS)
model. The Soave-Redlich-Kwong (SRK-EOS) model is chosen. Gas
mixture viscosity is calculated on the basis of the Lee-Gonzales-
Eakin (LGE) correlation. Numerical analysis of rapid gas
decompression process in rich and base natural gases is made on the
basis of the proposed mathematical model. The model is successfully
validated on the experimental data [1]. The proposed mathematical
model shows a very good agreement with the experimental data [1] in
a wide range of pressure values and predicts the decompression in
rich and base gas mixtures much better than analytical and
mathematical models, which are available from the open source
literature.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: Lean production (or lean management respectively)
gained popularity in several waves. The last three decades have been
filled with numerous attempts to apply these concepts in companies.
However, this has only been partially successful. The roots of lean
production can be traced back to Toyota-s just-in-time production.
This concept, which according to Womack-s, Jones- and Roos-
research at MIT was employed by Japanese car manufacturers,
became popular under its international names “lean production",
“lean-manufacturing" and was termed “Schlanke Produktion" in
Germany. This contribution shows a review about lean production in
Germany over the last thirty years: development, trial & error and
implementation as well.
Abstract: In this paper, we investigate a blind channel estimation method for Multi-carrier CDMA systems that use a subspace decomposition technique. This technique exploits the orthogonality property between the noise subspace and the received user codes to obtain channel of each user. In the past we used Singular Value Decomposition (SVD) technique but SVD have most computational complexity so in this paper use a new algorithm called URV Decomposition, which serve as an intermediary between the QR decomposition and SVD, replaced in SVD technique to track the noise space of the received data. Because of the URV decomposition has almost the same estimation performance as the SVD, but has less computational complexity.
Abstract: In this paper we address a multi-objective scheduling problem for unrelated parallel machines. In unrelated parallel systems, the processing cost/time of a given job on different machines may vary. The objective of scheduling is to simultaneously determine the job-machine assignment and job sequencing on each machine. In such a way the total cost of the schedule is minimized. The cost function consists of three components, namely; machining cost, earliness/tardiness penalties and makespan related cost. Such scheduling problem is combinatorial in nature. Therefore, a Simulated Annealing approach is employed to provide good solutions within reasonable computational times. Computational results show that the proposed approach can efficiently solve such complicated problems.
Abstract: The software industry has been considered a critical
infrastructure for any nation. Several studies have indicated that
national competitiveness increasingly depends upon Information and
Communication Technology (ICT), and software is one of the major
components of ICT, important for both large and small enterprises.
Even though there has been strong growth in the software industry in
Thailand, the industry has faced many challenges and problems that
need to be resolved. For example, the amount of pirated software has
been rising, and Thailand still has a large gap in the digital divide.
Additionally, the adoption among SMEs has been slow. This paper
investigates various issues in the software industry in Thailand, using
information acquired through analysis of secondary sources,
observation, and focus groups. The results of this study can be used
as “lessons learned" for the development of the software industry in
any developing country.
Abstract: The protection issues in distribution systems with open and closed-loop are studied, and a generalized protection setting scheme based on the traditional over current protection theories is proposed to meet the new requirements. The setting method is expected to be easier realized using computer program, so that the on-line adaptive setting for coordination in distribution system can be implemented. An automatic setting program is created and several cases are taken into practice. The setting results are verified by the coordination curves of the protective devices which are plotted using MATLAB.
Abstract: In this paper, based on the past project cost and time
performance, a model for forecasting project cost performance is
developed. This study presents a probabilistic project control concept
to assure an acceptable forecast of project cost performance. In this
concept project activities are classified into sub-groups entitled
control accounts. Then obtain the Stochastic S-Curve (SS-Curve), for
each sub-group and the project SS-Curve is obtained by summing
sub-groups- SS-Curves. In this model, project cost uncertainties are
considered through Beta distribution functions of the project
activities costs required to complete the project at every selected time
sections through project accomplishment, which are extracted from a
variety of sources. Based on this model, after a percentage of the
project progress, the project performance is measured via Earned
Value Management to adjust the primary cost probability distribution
functions. Then, accordingly the future project cost performance is
predicted by using the Monte-Carlo simulation method.
Abstract: Internet is nowadays included to all National Curriculums of the elementary school. A comparative study of their
goals leads to the conclusion that a complete curriculum should aim to student-s acquisition of the abilities to navigate and search for
information and additionally to emphasize on the evaluation of the information provided by the World Wide Web. In a constructivistic knowledge framework the design of a course has to take under
consideration the conceptual representations of students. The following paper presents the conceptual representation of students of eleven years old, attending the Sixth Grade of Greek Elementary School about World Wide Web and their use in the design and
implementation of an innovative course.
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.