Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy
Abstract: Environment today is featured with aging population,
increasing prevalence of chronic disease and complex of medical
treatment. Safe use of pharmaceutics relied very much on the efforts
made by both the health- related organizations and as well as the
government agencies. As far as the specialization concern in providing
health services to the patients, the government actively issued and
implemented the divisions of medical treatment and pharmaceutical to
improve the quality of care and to reduce medication errors and ensure
public health. Pharmaceutical sub-sector policy has been implemented
for 13 years. This study attempts to explore the factors that affect the
patients- behavior intention of refilling a prescription from a NHIB
pharmacy. Samples were those patients refilling their prescriptions
with the case NHIB pharmacies. A self-administered questionnaire
was used to collect respondents- information while the patients or
family members visit the pharmacy for the refilling. 1,200
questionnaires were dispatched in 37 pharmacies that randomly
selected from Pingtung City, Dongkang, Chaozhou, Hengchun areas.
732 responses were gained with 604 valid samples for further analyses.
Results of data analyses indicated that respondents- attitude,
subjective norm, perceived behavior control and behavior intentions
toward refilling behavior varied from some demographic variables to
another. This research also suggested adding actual behavior, either by
a self-report or observed, into the research.
Abstract: Product customization is an essential requirement for
manufacturing firms to achieve higher customers- satisfaction and
fulfill business target. In order to achieve these objectives, firms need
to handle both external varieties such as customer preference,
government regulations, cultural considerations etc and internal
varieties such as functional requirements of product, production
efficiency, quality etc. Both of the varieties need to be accumulated
and integrated together for the purpose of producing customized
product. These varieties are presented and discussed in this paper
along with the perspectives of modular product design and
development process. Other development strategies such as
modularity, component commonality, product family design and
product platform are presented with a view to achieve product variety
quickly and economically. A case example both for the concept of
modular design and platform based product development process is
also presented with the help of design structure matrix (DSM) tool.
This paper is concluded with several managerial implications and
future research direction.
Abstract: Recently, bianisotropic media again received
increasing importance in electromagnetic theory because of advances
in material science which enable the manufacturing of complex
bianisotropic materials. By using Maxwell's equations and
corresponding boundary conditions, the electromagnetic field
distribution in bianisotropic solenoid coils is determined and the
influence of the bianisotropic behaviour of coil to the impedance and
Q-factor is considered. Bianisotropic media are the largest class of
linear media which is able to describe the macroscopic material
properties of artificial dielectrics, artificial magnetics, artificial chiral
materials, left-handed materials, metamaterials, and other composite
materials. Several special cases of coils, filled with complex
substance, have been analyzed. Results obtained by using the
analytical approach are compared with values calculated by
numerical methods, especially by our new hybrid EEM/BEM method
and FEM.
Abstract: Prediction of benzene transport in soil and volatilization from soil to the atmosphere is important for the preservation of human health and management of contaminated soils. The adequacy of a simple numerical model, assuming two-phase diffusion and equilibrium of liquid/solid adsorption, was investigated by experimental data of benzene concentration in a flux chamber (with headspace) where Andosol and sand were filled. Adsorption experiment for liquid phase was performed to determine an adsorption coefficient. Furthermore, adequacy of vapor phase adsorption was also studied through two runs of experiment using sand with different water content. The results show that the model adequately predicted benzene transport and volatilization from Andosol and sand with water content of 14.0%. In addition, the experiment additionally revealed that vapor phase adsorption should be considered in diffusion model for sand with very low water content.
Abstract: The paper presents an investigation into the role of virtual reality and web technologies in the field of distance education. Within this frame, special emphasis is given on the building of web-based virtual learning environments so as to successfully fulfill their educational objectives. In particular, basic pedagogical methods are studied, focusing mainly on the efficient preparation, approach and presentation of learning content, and specific designing rules are presented considering the hypermedia, virtual and educational nature of this kind of applications. The paper also aims to highlight the educational benefits arising from the use of virtual reality technology in medicine and study the emerging area of web-based medical simulations. Finally, an innovative virtual reality environment for distance education in medicine is demonstrated. The proposed environment reproduces conditions of the real learning process and enhances learning through a real-time interactive simulator.
Abstract: This research aims to study employment trends in
printing industry for prepress support by Suan Sunandha University
Fund. The objectives of this research are to explain the trends of the
employment in Thai Printing Industry for prepress in Bangkok and
the description of different personnel that prepress entrepreneur need
and also the problems of employment.
The population of prepress entrepreneurs is about 100
organizations in the area of Bangkok. The questionnaires has been
taken and analyzed with SPSS program by using the average
percentage and standard deviation.
This research is multiple case studies. The conceptual framework
is developed on the basis of the open systems theory.
The research result show that
1. The most of prepress entrepreneur have trend to choose the
employee by any sex, the age 25-29 years old, bachelor degree
and have 1-2 years experience.
2. The most problems are the understanding in job,
communication/relation and the understanding in new
technology.
3. The trends aims to employment in 1-3 years have 57.8% for
prepress industry in Bangkok.
This research suggests that:
1. Thai printing industry for prepress in Bangkok need quality
employee that expert in printing technology.
2. Prepress entrepreneur should have agreement to development
with university for practice the employee.
3. Prepress entrepreneur should support personal to fulfill the
knowledge.
Abstract: The European countries that during the past two
decades based their exchange rate regimes on currency board
arrangement (CBA) are usually analysed from the perspective of
corner solution choice’s stabilisation effects. There is an open
discussion on the positive and negative background of a strict
exchange rate regime choice, although it should be seen as part of the
transition process towards the monetary union membership. The
focus of the paper is on the Baltic countries that after two decades of
a rigid exchange rate arrangement and strongly influenced by global
crisis are finishing their path towards the euro zone. Besides the
stabilising capacity, the CBA is highly vulnerable regime, with
limited developing potential. The rigidity of the exchange rate (and
monetary) system, despite the ensured credibility, do not leave
enough (or any) space for the adjustment and/or active crisis
management. Still, the Baltics are in a process of recovery, with fiscal
consolidation measures combined with (painful and politically
unpopular) measures of internal devaluation. Today, two of them
(Estonia and Latvia) are members of euro zone, fulfilling their
ultimate transition targets, but de facto exchanging one fixed regime
with another.
The paper analyses the challenges for the CBA in unstable
environment since the fixed regimes rely on imported stability and
are sensitive to external shocks. With limited monetary instruments,
these countries were oriented to the fiscal policies and used a
combination of internal devaluation and tax policy measures. Despite
their rather quick recovery, our second goal is to analyse the long
term influence that the measures had on the national economy.
Abstract: The main problem is that there is a very low innovation performance in Latvia. Since Latvia is a Member State of European Union, it also shall have to fulfill the set targets and to improve innovative results.Universities are one of the main performers to provide innovative capacity of country. University, industry and government need to cooperate for getting best results.The intellectual property is one of the indicators to determine innovation level in the country or organization, and patents are one of the characteristics of intellectual property.The objective of the article is to determine indicators characterizing innovative environment in Latvia and influence of the development of universities on them.The methods that will be used in the article to achieve the objectives are quantitative and qualitative analysis of the literature, statistical data analysis and graphical analysis methods.
Abstract: A procedure for the preparation of clarified Pawpaw
Juice was developed. About 750ml Pawpaw pulp was measured into
2 measuring cylinders A & B of capacity 1 litre heated to 400C,
cooled to 200C. 30mls pectinase was added into cylinder A, while
30mls distilled water was added into cylinder B. Enzyme treated
sample (A) was allowed to digest for 5hours after which it was heated
to 900C for 15 minutes to inactivate the enzyme. The heated sample
was cooled and with the aid of a mucillin cloth the pulp was filtered
to obtain the clarified pawpaw juice. The juice was filled into 100ml
plastic bottles, pasteurized at 950C for 45 minutes, cooled and stored
at room temperature. The sample treated with 30mls distilled water
also underwent the same process. Freshly pasteurized sample was
analyzed for specific gravity, titratable acidity, pH, sugars and
ascorbic acid. The remaining sample was then stored for 2 weeks and
the above analyses repeated. There were differences in the results of
the freshly pasteurized samples and stored sample in pH and ascorbic
acid levels, also sample treated with pectinase yielded higher
volumes of juice than that treated with distilled water.
Abstract: Proper management of residues originated from
industrial activities is considered as one of the serious challenges
faced by industrial societies due to their potential hazards to the
environment. Common disposal methods for industrial solid wastes
(ISWs) encompass various combinations of solely management
options, i.e. recycling, incineration, composting, and sanitary
landfilling. Indeed, the procedure used to evaluate and nominate the
best practical methods should be based on environmental, technical,
economical, and social assessments. In this paper an environmentaltechnical
assessment model is developed using analytical network
process (ANP) to facilitate the decision making practice for ISWs
generated at Gilan province, Iran. Using the results of performed
surveys on industrial units located at Gilan, the various groups of
solid wastes in the research area were characterized, and four
different ISW management scenarios were studied. The evaluation
process was conducted using the above-mentioned model in the
Super Decisions software (version 2.0.8) environment. The results
indicates that the best ISW management scenario for Gilan province
is consist of recycling the metal industries residues, composting the
putrescible portion of ISWs, combustion of paper, wood, fabric and
polymeric wastes as well as energy extraction in the incineration
plant, and finally landfilling the rest of the waste stream in addition
with rejected materials from recycling and compost production plants
and ashes from the incineration unit.
Abstract: The so-called all-pass filter circuits are commonly
used in the field of signal processing, control and measurement.
Being connected to capacitive loads, these circuits tend to loose their
stability; therefore the elaborate analysis of their dynamic behavior is
necessary. The compensation methods intending to increase the
stability of such circuits are discussed in this paper, including the socalled
lead-lag compensation technique being treated in detail. For
the dynamic modeling, a two-port network model of the all-pass filter
is being derived. The results of the model analysis show, that
effective lead-lag compensation can be achieved, alone by the
optimization of the circuit parameters; therefore the application of
additional electric components are not needed to fulfill the stability
requirement.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: Due to growing environmental concerns of the cement
industry, alternative cement technologies have become an area of
increasing interest. It is now believed that new binders are
indispensable for enhanced environmental and durability
performance. Self-compacting Geopolymer concrete is an innovative
method and improved way of concreting operation that does not
require vibration for placing it and is produced by complete
elimination of ordinary Portland cement.
This paper documents the assessment of the compressive strength
and workability characteristics of low-calcium fly ash based selfcompacting
geopolymer concrete. The essential workability
properties of the freshly prepared Self-compacting Geopolymer
concrete such as filling ability, passing ability and segregation
resistance were evaluated by using Slump flow, V-funnel, L-box and
J-ring test methods. The fundamental requirements of high
flowability and segregation resistance as specified by guidelines on
Self Compacting Concrete by EFNARC were satisfied. In addition,
compressive strength was determined and the test results are included
here. This paper also reports the effect of extra water, curing time and
curing temperature on the compressive strength of self-compacting
geopolymer concrete. The test results show that extra water in the
concrete mix plays a significant role. Also, longer curing time and
curing the concrete specimens at higher temperatures will result in
higher compressive strength.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: Integration of process planning and scheduling
functions is necessary to achieve superior overall system
performance. This paper proposes a methodology for integration of
process planning and scheduling for prismatic component that can be
implemented in a company with existing departments. The developed
model considers technological constraints whereas available time for
machining in shop floor is the limiting factor to produce multiple
process plan (MPP). It takes advantage of MPP while guarantied the
fulfillment of the due dates via using overtime. This study has been
proposed to determinate machining parameters, tools, machine and
amount of over time within the minimum cost objective while
overtime is considered for this. At last the illustration shows that the
system performance is improved by as measured by cost and
compatible with due date.
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.
Abstract: A general purpose viscous flow solver Ansys CFX
was used to solve the unsteady three-dimensional (3D) Reynolds
Averaged Navier-Stokes Equation (RANSE) for simulating a 3D
numerical viscous wave tank. A flap-type wave generator was
incorporated in the computational domain to generate the desired
incident waves. Authors have made effort to study the physical
behaviors of Flap type wave maker with governing parameters.
Dependency of the water fill depth, Time period of oscillations and
amplitude of oscillations of flap were studied. Effort has been made
to establish relations between parameters. A validation study was
also carried out against CFD methodology with wave maker theory.
It has been observed that CFD results are in good agreement with
theoretical results. Beaches of different slopes were introduced to
damp the wave, so that it should not cause any reflection from
boundary. As a conclusion this methodology can simulate the
experimental wave-maker for regular wave generation for different
wave length and amplitudes.
Abstract: Primary studies are being carried out in Turkey for
expanding information and communication technologies (ICT) aided instruction activities. Subject of the present study is to identify
whether those studies achieved their goals in the application. Information technologies (IT) formative teachers in the primary
schools, and academicians in the faculties of education were interviewed to investigate the process and results of implementing
computer-aided instruction methods whose basis is strengthened in theory. Analysis of the results gained from two separate surveys
demonstrated that capability of the teachers in elementary education institutions for carrying into effect computer-aided instruction and
technical infrastructure has not been established for computer-aided instruction practices yet. Prospective teachers must be well-equipped in ICT to duly fulfill requirements of modern education and also
must be self-confident. Finally, scope and intensity of the courses given in connection with teaching of the ICT in faculties of education needs to be revised.