Abstract: It is important to remove manganese from water
because of its effects on human and the environment. Human
activities are one of the biggest contributors for excessive manganese
concentration in the environment. The proposed method to remove
manganese in aqueous solution by using adsorption as in carbon
nanotubes (CNT) at different parameters: The parameters are CNT
dosage, pH, agitation speed and contact time. Different pHs are pH
6.0, pH 6.5, pH 7.0, pH 7.5 and pH 8.0, CNT dosages are 5mg,
6.25mg, 7.5mg, 8.75mg or 10mg, contact time are 10 min, 32.5 min,
55 min, 87.5 min and 120 min while the agitation speeds are 100rpm,
150rpm, 200rpm, 250rpm and 300rpm. The parameters chosen for
experiments are based on experimental design done by using Central
Composite Design, Design Expert 6.0 with 4 parameters, 5 levels and
2 replications. Based on the results, condition set at pH 7.0, agitation
speed of 300 rpm, 7.5mg and contact time 55 minutes gives the
highest removal with 75.5%. From ANOVA analysis in Design
Expert 6.0, the residual concentration will be very much affected by
pH and CNT dosage. Initial manganese concentration is 1.2mg/L
while the lowest residual concentration achieved is 0.294mg/L,
which almost satisfy DOE Malaysia Standard B requirement.
Therefore, further experiments must be done to remove manganese
from model water to the required standard (0.2 mg/L) with the initial
concentration set to 0.294 mg/L.
Abstract: In non destructive testing by radiography, a perfect
knowledge of the weld defect shape is an essential step to
appreciate the quality of the weld and make decision on its
acceptability or rejection. Because of the complex nature of the
considered images, and in order that the detected defect region
represents the most accurately possible the real defect, the choice
of thresholding methods must be done judiciously. In this paper,
performance criteria are used to conduct a comparative study of
four non parametric histogram thresholding methods for automatic
extraction of weld defect in radiographic images.
Abstract: This paper presents the effectiveness of artificial
intelligent technique to apply for pattern recognition and
classification of Partial Discharge (PD). Characteristics of PD signal
for pattern recognition and classification are computed from the
relation of the voltage phase angle, the discharge magnitude and the
repeated existing of partial discharges by using statistical and fractal
methods. The simplified fuzzy ARTMAP (SFAM) is used for pattern
recognition and classification as artificial intelligent technique. PDs
quantities, 13 parameters from statistical method and fractal method
results, are inputted to Simplified Fuzzy ARTMAP to train system
for pattern recognition and classification. The results confirm the
effectiveness of purpose technique.
Abstract: In this paper, SFQ (Start Time Fair Queuing)
algorithm is analyzed when this is applied in computer networks to
know what kind of behavior the traffic in the net has when different
data sources are managed by the scheduler. Using the NS2 software
the computer networks were simulated to be able to get the graphs
showing the performance of the scheduler. Different traffic sources
were introduced in the scripts, trying to establish the real scenario.
Finally the results were that depending on the data source, the traffic
can be affected in different levels, when Constant Bite Rate is
applied, the scheduler ensures a constant level of data sent and
received, but the truth is that in the real life it is impossible to ensure
a level that resists the changes in work load.
Abstract: Conventional WBL is effective for meaningful student, because rote student learn by repeating without thinking or trying to understand. It is impossible to have full benefit from conventional WBL. Understanding of rote student-s intention and what influences it becomes important. Poorly designed user interface will discourage rote student-s cultivation and intention to use WBL. Thus, user interface design is an important factor especially when WBL is used as comprehensive replacement of conventional teaching. This research proposes the influencing factors that can enhance student-s intention to use the system. The enhanced TAM is used for evaluating the proposed factors. The research result points out that factors influencing rote student-s intention are Perceived Usefulness of Homepage Content Structure, Perceived User Friendly Interface, Perceived Hedonic Component, and Perceived (homepage) Visual Attractiveness.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.
Abstract: This paper deals with the effect of a power transformer’s vector group on the basic voltage sag characteristics during unbalanced faults at a meshed or radial power network. Specifically, the propagation of voltage sags through a power transformer is studied with advanced short-circuit analysis. A smart method to incorporate this effect on analytical mathematical expressions is proposed. Based on this methodology, the positive effect of transformers of certain vector groups on the mitigation of the expected number of voltage sags per year (sag frequency) at the terminals of critical industrial customers can be estimated.
Abstract: The main problem for recognition of handwritten Persian digits using Neural Network is to extract an appropriate feature vector from image matrix. In this research an asymmetrical segmentation pattern is proposed to obtain the feature vector. This pattern can be adjusted as an optimum model thanks to its one degree of freedom as a control point. Since any chosen algorithm depends on digit identity, a Neural Network is used to prevail over this dependence. Inputs of this Network are the moment of inertia and the center of gravity which do not depend on digit identity. Recognizing the digit is carried out using another Neural Network. Simulation results indicate the high recognition rate of 97.6% for new introduced pattern in comparison to the previous models for recognition of digits.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any existing
network infrastructure or centralized administration. Because of the
limited transmission range of wireless network interfaces, multiple
"hops" may be needed to exchange data across the network. In order
to facilitate communication within the network, a routing protocol is
used to discover routes between nodes. The primary goal of such an
ad hoc network routing protocol is correct and efficient route
establishment between a pair of nodes so that messages may be
delivered in a timely manner. Route construction should be done
with a minimum of overhead and bandwidth consumption. This paper
examines two routing protocols for mobile ad hoc networks– the
Destination Sequenced Distance Vector (DSDV), the table- driven
protocol and the Ad hoc On- Demand Distance Vector routing
(AODV), an On –Demand protocol and evaluates both protocols
based on packet delivery fraction, normalized routing load, average
delay and throughput while varying number of nodes, speed and
pause time.
Abstract: The design of Class A and Class AB 2-stage X band
Power Amplifier is described in this report. This power amplifier is
part of a transceiver used in radar for monitoring iron characteristics
in a blast furnace. The circuit was designed using foundry WIN
Semiconductors. The specification requires 15dB gain in the linear
region, VSWR nearly 1 at input as well as at the output, an output
power of 10 dBm and good stable performance in the band 10.9-12.2
GHz. The design was implemented by using inter-stage
configuration, the Class A amplifier was chosen for driver stage i.e.
the first amplifier focusing on the gain and the output amplifier
conducted at Class AB with more emphasis on output power.
Abstract: Virtualization and high performance computing have been discussed from a performance perspective in recent publications. We present and discuss a flexible and efficient approach to the management of virtual clusters. A virtual machine management tool is extended to function as a fabric for cluster deployment and management. We show how features such as saving the state of a running cluster can be used to avoid disruption. We also compare our approach to the traditional methods of cluster deployment and present benchmarks which illustrate the efficiency of our approach.
Abstract: The hydrothermal behavior of a bed consisting of
magnetic and shale oil particle admixtures under the effect of a
transverse magnetic field is investigated. The phase diagram, bed
void fraction are studied under wide range of the operating
conditions i.e., gas velocity, magnetic field intensity and fraction of
the magnetic particles. It is found that the range of the stabilized
regime is reduced as the magnetic fraction decreases. In addition, the
bed voidage at the onset of fluidization decreases as the magnetic
fraction decreases. On the other hand, Nusselt number and
consequently the heat transfer coefficient is found to increase as the
magnetic fraction decreases. An empirical equation is investigated to
relate the effect of the gas velocity, magnetic field intensity and
fraction of the magnetic particles on the heat transfer behavior in the
bed.
Abstract: In this paper we propose a novel method for human
face segmentation using the elliptical structure of the human head. It
makes use of the information present in the edge map of the image.
In this approach we use the fact that the eigenvalues of covariance
matrix represent the elliptical structure. The large and small
eigenvalues of covariance matrix are associated with major and
minor axial lengths of an ellipse. The other elliptical parameters are
used to identify the centre and orientation of the face. Since an
Elliptical Hough Transform requires 5D Hough Space, the Circular
Hough Transform (CHT) is used to evaluate the elliptical parameters.
Sparse matrix technique is used to perform CHT, as it squeeze zero
elements, and have only a small number of non-zero elements,
thereby having an advantage of less storage space and computational
time. Neighborhood suppression scheme is used to identify the valid
Hough peaks. The accurate position of the circumference pixels for
occluded and distorted ellipses is identified using Bresenham-s
Raster Scan Algorithm which uses the geometrical symmetry
properties. This method does not require the evaluation of tangents
for curvature contours, which are very sensitive to noise. The method
has been evaluated on several images with different face orientations.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: In the course of the present work, plain (nonencapsulated)
and microencapsulated polyphenols were produced
using olive mill wastewater (OMW) as raw material, in order to be
used for enrichment of yogurt and dairy products. The OMW was
first clarified by using membrane technology and subsequently the
contained poly-phenols were isolated by adsorption-desorption
technique using selective macro-porous resins and finally recovered
in dry form after been processed by RO membrane technique
followed by freeze drying. Moreover, the polyphenols were
encapsulated in modified starch by freeze drying in order to mask the
color and bitterness effect and improve their functionality. The two
products were used successfully as additives in yogurt preparations
and the produced products were acceptable by the consumers and
presented with certain advantage to the plain yogurt. For the herein
proposed production scheme a patent application was already
submitted.
Abstract: Technology transfer is a common method for
companies to acquire new technology and presents both challenges
and substantial benefits. In some cases especially in developing
countries, the mere possession of technology does not guarantee a
competitive advantage if the appropriate infrastructure is not in place.
In this paper, we identify the localization factors needed to provide a
better understanding of the conditions necessary for localization in
order to benefit from future technology developments. Our
theoretical and empirical analyses allow us to identify several factors
in the technology transfer process that affect localization and provide
leverage in enhancing capabilities and absorptive capacity.The
impact factors are categorized within different groups of government,
firms, institutes and market, and are verified through the empirical
survey of a technology transfer experience. Moreover, statistical
analysis has allowed a deeper understanding of the importance of
each factor and has enabled each group to prioritize their
organizational policies to effectively localize their technology.
Abstract: In this work, a new approach is proposed to control
the manipulators for Humanoid robot. The kinematics of the
manipulators in terms of joint positions, velocity, acceleration and
torque of each joint is computed using the Denavit Hardenberg (D-H)
notations. These variables are used to design the manipulator control
system, which has been proposed in this work. In view of supporting
the development of a controller, a simulation of the manipulator is
designed for Humanoid robot. This simulation is developed through
the use of the Virtual Reality Toolbox and Simulink in Matlab. The
Virtual Reality Toolbox in Matlab provides the interfacing and
controls to an environment which is developed based on the Virtual
Reality Modeling Language (VRML). Chains of bones were used to
represent the robot.
Abstract: Cooperative diversity (CD) has been adopted in many communication systems because it helps in improving performance of the wireless communication systems with the help of the relays that emulate the multiple antenna terminals. This work aims to provide the derivation of the performance analysis expressions of the multiuser diversity (MUD) in the two-hop cooperative multi-relay wireless networks (TCMRNs). Considering the work analysis, we provide analytically the derivation of a closed form expression of the two most commonly used performance metrics namely, the outage probability and the symbol error probability (SEP) for the fixed decode-and-forward (FDF) protocol with MUD.
Abstract: Ice cover County has a significant impact on rivers as it affects with the ice melting capacity which results in flooding, restrict navigation, modify the ecosystem and microclimate. River ices are made up of different ice types with varying ice thickness, so surveillance of river ice plays an important role. River ice types are captured using infrared imaging camera which captures the images even during the night times. In this paper the river ice infrared texture images are analysed using first-order statistical methods and secondorder statistical methods. The second order statistical methods considered are spatial gray level dependence method, gray level run length method and gray level difference method. The performance of the feature extraction methods are evaluated by using Probabilistic Neural Network classifier and it is found that the first-order statistical method and second-order statistical method yields low accuracy. So the features extracted from the first-order statistical method and second-order statistical method are combined and it is observed that the result of these combined features (First order statistical method + gray level run length method) provides higher accuracy when compared with the features from the first-order statistical method and second-order statistical method alone.
Abstract: Nowadays pharmaceutical care departments located in
hospitals are amongst the important pillars of the healthcare system.
The aim of this study was to evaluate quality of hospital drugstores
affiliated with Kermanshah University of Medical Sciences.
In this cross-sectional study a validated questionnaire was used.
The questionnaire was filled in by the one of the researchers in all
seventeen hospital drugstores located in the teaching and nonteaching
hospitals affiliated with Kermanshah University of Medical
Sciences. The results shows that in observed hospitals,24% of
pharmacy environments, 25% of pharmacy store and storage
conditions, 49% of storage procedure, 25% of ordering drugs and
supplies, 73% of receiving supplies (proper procedure are fallowed
for receiving supplies), 35% of receiving supplies (prompt action
taken if deterioration of drugs received is suspected), 23.35% of
drugs delivery to patients and finally 0% of stock cards are used for
proper inventory control have full compliance with standards.