Abstract: Counting people from a video stream in a noisy environment is a challenging task. This project aims at developing a counting system for transport vehicles, integrated in a video surveillance product. This article presents a method for the detection and tracking of multiple faces in a video by using a model of first and second order local moments. An iterative process is used to estimate the position and shape of multiple faces in images, and to track them. the trajectories are then processed to count people entering and leaving the vehicle.
Abstract: There are various kinds of medical equipment which
requires relatively accurate positional adjustments for successful
treatment. However, patients tend to move without notice during a
certain span of operations. Therefore, it is common practice that
accompanying operators adjust the focus of the equipment. In this
paper, tracking controllers for medical equipment are suggested to
replace the operators. The tracking controllers use AHRS sensor
information to recognize the movements of patients. Sensor fusion is
applied to reducing the error magnitudes through linear Kalman filters.
The image processing of optical markers is included to adjust the
accumulation errors of gyroscope sensor data especially for yaw
angles.
The tracking controller reduces the positional errors between the
current focus of a device and the target position on the body of a
patient. Since the sensing frequencies of AHRS sensors are very high
compared to the physical movements, the control performance is
satisfactory. The typical applications are, for example, ESWT or
rTMS, which have the error ranges of a few centimeters.
Abstract: Fuzzy logic approach is used in this study to predict
the tractive performance in terms of traction force, and motion
resistance for an intelligent air cushion track vehicle while it operates
in the swamp peat. The system is effective to control the intelligent
air –cushion system with measuring the vehicle traction force (TF),
motion resistance (MR), cushion clearance height (CH) and cushion
pressure (CP). Sinkage measuring sensor, magnetic switch, pressure
sensor, micro controller, control valves and battery are incorporated
with the Fuzzy logic system (FLS) to investigate experimentally the
TF, MR, CH, and CP. In this study, a comparison for tractive
performance of an intelligent air cushion track vehicle has been
performed with the results obtained from the predicted values of FLS
and experimental actual values. The mean relative error of actual and
predicted values from the FLS model on traction force, and total
motion resistance are found as 5.58 %, and 6.78 % respectively. For
all parameters, the relative error of predicted values are found to be
less than the acceptable limits. The goodness of fit of the prediction
values from the FLS model on TF, and MR are found as 0.90, and
0.98 respectively.
Abstract: In this paper, a solution is presented for a robotic
manipulation problem in industrial settings. The problem is sensing
objects on a conveyor belt, identifying the target, planning and
tracking an interception trajectory between end effector and the
target. Such a problem could be formulated as combining object
recognition, tracking and interception. For this purpose, we integrated
a vision system to the manipulation system and employed tracking
algorithms. The control approach is implemented on a real industrial
manipulation setting, which consists of a conveyor belt, objects
moving on it, a robotic manipulator, and a visual sensor above the
conveyor. The trjectory for robotic interception at a rendezvous point
on the conveyor belt is analytically calculated. Test results show that
tracking the raget along this trajectory results in interception and
grabbing of the target object.
Abstract: In the last years numerous applications of Human-
Computer Interaction have exploited the capabilities of Time-of-
Flight cameras for achieving more and more comfortable and precise
interactions. In particular, gesture recognition is one of the most active
fields. This work presents a new method for interacting with a virtual
object in a 3D space. Our approach is based on the fusion of depth
data, supplied by a ToF camera, with color information, supplied
by a HD webcam. The hand detection procedure does not require
any learning phase and is able to concurrently manage gestures of
two hands. The system is robust to the presence in the scene of
other objects or people, thanks to the use of the Kalman filter for
maintaining the tracking of the hands.
Abstract: A model to identify the lifetime of target tracking
wireless sensor network is proposed. The model is a static clusterbased
architecture and aims to provide two factors. First, it is to
increase the lifetime of target tracking wireless sensor network.
Secondly, it is to enable good localization result with low energy
consumption for each sensor in the network. The model consists of
heterogeneous sensors and each sensing member node in a cluster
uses two operation modes–active mode and sleep mode. The
performance results illustrate that the proposed architecture consumes
less energy and increases lifetime than centralized and dynamic
clustering architectures, for target tracking sensor network.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: The authors present optimization parameters of rotary
positioner controller in hard disk drive servo track writing process
using coefficient diagram method; CDM. Due to estimation
parameters in PI Positioning Control System by expected ratio
method cannot meet the required specification of response
effectively, we suggest coefficient diagram method for defining
controller parameters under the requirement of the system. Finally,
the simulation results show that our proposed method can improve
the problem in tuning parameter of rotary positioner controller. It is
satisfied specification of performance of control system. Furthermore,
it is very convenient as a fast adjustment damping ratio as well as a
high speed response.
Abstract: This paper presents a particle swarm optimization
(PSO) based approach for multiple object tracking based on histogram
matching. To start with, gray-level histograms are calculated to
establish a feature model for each of the target object. The difference
between the gray-level histogram corresponding to each particle in the
search space and the target object is used as the fitness value. Multiple
swarms are created depending on the number of the target objects
under tracking. Because of the efficiency and simplicity of the PSO
algorithm for global optimization, target objects can be tracked as
iterations continue. Experimental results confirm that the proposed
PSO algorithm can rapidly converge, allowing real-time tracking of
each target object. When the objects being tracked move outside the
tracking range, global search capability of the PSO resumes to re-trace
the target objects.
Abstract: This paper describes the application of a model predictive controller to the problem of batch reactor temperature control. Although a great deal of work has been done to improve reactor throughput using batch sequence control, the control of the actual reactor temperature remains a difficult problem for many operators of these processes. Temperature control is important as many chemical reactions are sensitive to temperature for formation of desired products. This controller consist of two part (1) a nonlinear control method GLC (Global Linearizing Control) to create a linear model of system and (2) a Model predictive controller used to obtain optimal input control sequence. The temperature of reactor is tuned to track a predetermined temperature trajectory that applied to the batch reactor. To do so two input signals, electrical powers and the flow of coolant in the coil are used. Simulation results show that the proposed controller has a remarkable performance for tracking reference trajectory while at the same time it is robust against noise imposed to system output.
Abstract: This paper deals with dynamic load balancing using PVM. In distributed environment Load Balancing and Heterogeneity are very critical issues and needed to drill down in order to achieve the optimal results and efficiency. Various techniques are being used in order to distribute the load dynamically among different nodes and to deal with heterogeneity. These techniques are using different approaches where Process Migration is basic concept with different optimal flavors. But Process Migration is not an easy job, it impose lot of burden and processing effort in order to track each process in nodes. We will propose a dynamic load balancing technique in which application will intelligently balance the load among different nodes, resulting in efficient use of system and have no overheads of process migration. It would also provide a simple solution to problem of load balancing in heterogeneous environment.
Abstract: The results show that the bridge equipped with seismic isolation bearing system shows a high amount of energy dissipation. The purpose of the present study is to analyze the overall performance of continuous curved highway viaducts with different bearing supports, with an emphasis on the effectiveness of seismic isolation based on lead rubber bearing and hedge reaction force bearing system consisted of friction sliding bearing and rubber bearing. The bridge seismic performance has been evaluated on six different cases with six bearing models. The effects of the different arrangement of bearing on the deck superstructure displacements, the seismic damage at the bottom of the piers, movement track at the pier-s top and the total and strain energies absorbed by the structure are evaluated. In conclusion, the results provide sufficient evidence of the effectiveness on the use of seismic isolation on steel curved highway bridges.
Abstract: Optical 1x12 fused-taper-twisted polymer optical fiber (POF) couplers has been fabricated by a perform technique. Characterization of the coupler which proposed to be used in passive night vision application to tracking a blind sport area was reported. During the development process of fused-taper-twisted POF couplers was carried out, red LED fully utilized to be injected into the couplers to test the quality of fabricated couplers. Some characterization parameters, such as optical output power, POFs attenuation characteristics and power losses on the network were observed. The maximum output power efficiency of the coupler is about 40%, but it can be improved gradually through experience and practice.
Abstract: One of the methods for detecting the target position
error in the laser tracking systems is using Four Quadrant (4Q)
detectors. If the coordinates of the target center is yielded through the
usual relations of the detector outputs, the results will be nonlinear,
dependent on the shape, target size and its position on the detector
screen. In this paper we have designed an algorithm with using
neural network that coordinates of the target center in laser tracking
systems is calculated by using detector outputs obtained from visual
modeling. With this method, the results except from the part related
to the detector intrinsic limitation, are linear and dependent from the
shape and target size.
Abstract: This paper shows the potential system benefits of
simple tracking solar system using a stepper motor and light sensor.
This method is increasing power collection efficiency by developing
a device that tracks the sun to keep the panel at a right angle to its
rays. A solar tracking system is designed, implemented and
experimentally tested. The design details and the experimental results
are shown.
Abstract: This study offers a new simple method for assessing
an axial part-through crack in a pipe wall. The method utilizes simple
approximate expressions for determining the fracture parameters K,
J, and employs these parameters to determine critical dimensions of a
crack on the basis of equality between the J-integral and the J-based
fracture toughness of the pipe steel. The crack tip constraint is taken
into account by the so-called plastic constraint factor C, by which the
uniaxial yield stress in the J-integral equation is multiplied. The
results of the prediction of the fracture condition are verified by burst
tests on test pipes.
Abstract: Protective coatings that resist oxide scale growth and
decrease chromium evaporation are necessary to make stainless steel
interconnect materials for long-term durable operation of solid oxide
fuel cells (SOFCs). In this study a layer of cobalt was electroplated
on the surface of AISI 441 ferritic stainless steel which is used in
solid oxide fuel cells for interconnect applications. The oxidation
behavior of coated substrates was studied as a function of time at
operating conditions of SOFCs. Cyclic oxidation has been also tested
at 800ºC for 100 cycles. Cobalt coating during isothermal oxidation
caused to the oxide growth resistance by limiting the outward
diffusion of Cr cation and the inward diffusion of oxygen anion.
Results of cyclic oxidation exhibited that coated substrates
demonstrate an excellent resistance against the spallation and
cracking.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: Opinion extraction about products from customer
reviews is becoming an interesting area of research. Customer
reviews about products are nowadays available from blogs and
review sites. Also tools are being developed for extraction of opinion
from these reviews to help the user as well merchants to track the
most suitable choice of product. Therefore efficient method and
techniques are needed to extract opinions from review and blogs. As
reviews of products mostly contains discussion about the features,
functions and services, therefore, efficient techniques are required to
extract user comments about the desired features, functions and
services. In this paper we have proposed a novel idea to find features
of product from user review in an efficient way. Our focus in this
paper is to get the features and opinion-oriented words about
products from text through auxiliary verbs (AV) {is, was, are, were,
has, have, had}. From the results of our experiments we found that
82% of features and 85% of opinion-oriented sentences include AVs.
Thus these AVs are good indicators of features and opinion
orientation in customer reviews.