Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: The success of an electronic system in a System-on- Chip is highly dependent on the efficiency of its interconnection network, which is constructed from routers and channels (the routers move data across the channels between nodes). Since neither classical bus based nor point to point architectures can provide scalable solutions and satisfy the tight power and performance requirements of future applications, the Network-on-Chip (NoC) approach has recently been proposed as a promising solution. Indeed, in contrast to the traditional solutions, the NoC approach can provide large bandwidth with moderate area overhead. The selected topology of the components interconnects plays prime rule in the performance of NoC architecture as well as routing and switching techniques that can be used. In this paper, we present two generic NoC architectures that can be customized to the specific communication needs of an application in order to reduce the area with minimal degradation of the latency of the system. An experimental study is performed to compare these structures with basic NoC topologies represented by 2D mesh, Butterfly-Fat Tree (BFT) and SPIN. It is shown that Cluster mesh (CMesh) and MinRoot schemes achieves significant improvements in network latency and energy consumption with only negligible area overhead and complexity over existing architectures. In fact, in the case of basic NoC topologies, CMesh and MinRoot schemes provides substantial savings in area as well, because they requires fewer routers. The simulation results show that CMesh and MinRoot networks outperforms MESH, BFT and SPIN in main performance metrics.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: This paper addresses the problem of trajectory
tracking control of an underactuated autonomous underwater vehicle
(AUV) in the horizontal plane. The underwater vehicle under
consideration is not actuated in the sway direction, and the system
matrices are not assumed to be diagonal and linear, as often found in
the literature. In addition, the effect of constant bias of environmental
disturbances is considered. Using backstepping techniques and the
tracking error dynamics, the system states are stabilized by forcing
the tracking errors to an arbitrarily small neighborhood of zero. The
effectiveness of the proposed control method is demonstrated through
numerical simulations. Simulations are carried out for an
experimental vehicle for smooth, inertial, two dimensional (2D)
reference trajectories such as constant velocity trajectory (a circle
maneuver – constant yaw rate), and time varying velocity trajectory
(a sinusoidal path – sinusoidal yaw rate).
Abstract: The aim of this study was to examine and identify the
type of Iranian financial market in terms of being symmetrical or
asymmetrical and to measure relationship between type of market
and the market's indices. In this study, daily information on the
market-s Share Price Index, Industrial Index and Top Fifty Most
Active Companies during the years 1999-2010 has been used. In
addition, to determine type of the financial market, rate of return on
Security is taken into account. In this research, by using logistic
regression analysis methods, relationship of the market type with the
above mentioned indices have been examined. The results showed
that the type of the financial market has a positive significant
association with market share price index and Industrial Index. Index
of Top Fifty Most Active Companies is significantly associated with
type of financial market, however this relationship is inverse.
Abstract: In order to evaluate the Effects of dual inoculation of
Azotobacter and Mycorrhiza with Nitrogen and Phosphorus levels on
yield and yield components of spring safflower, this study was
carried out in field of Farahan university in Markazi province in
2007. A factorial in a randomized complete block design with three
replications was used inoculation of Azotobacter (with inoculation
and without inoculation) and Mycorrhiza (with inoculation and
without inoculation ) with Nitrogen and Phosphorus levels [F0= N0+
P0 (kg.ha-1), F1= N50+ P25(kg.ha-1), F2= N100+ P50(kg.ha-1) and
F3= N150+ P75 (kg.ha-1)] on spring safflower (cultivar IL-111). In
this study characteristics such as: Harvest index, Hectolitre weight,
Root dry weight, Seed yield, Mycorrhizal Colonization Root,
Number of days to maturity were assessed. Results indicated that
treatment (A0M1F3) with grain yield (1556 kg.ha-1) and treatment
(A0M1F0) with grain yield (918 kg.ha-1) were significantly superior
to the other treatments and according to calculated, inoculation seeds
in plantig date with Azotobacter and Mycorrhiza to cause increase
grain yield about 5/38 percentage. we can by inoculation safflower
seeds with Azotobacter and Mycorrhiza too easily at the time sowing
date. The purpose of this research, study and evaluation the role of
biological fixation N and P, to provide for feeds plants.
Abstract: Deflocculation and gel characterization were
investigated for three different composition of porcelain slips at
specific gravity 1.8. The suspensions were dispersed with sodium
silicate (Na2SiO3) in under-deflocculated slips and fully deflocculated
slips. The rheology characterization of slips was conducted by the
deflocculation curves and the gel curves. The results showed that
decreasing the amount of the ball clay composition in the slips
consumed less dosages of the dispersants. The under-deflocculated
slips tended to have a gelation rate faster than the fully deflocculated
slips.
Abstract: In Geographic Information System, one of the sources
of obtaining needed geographic data is digitizing analog maps and
evaluation of aerial and satellite photos. In this study, a method will
be discussed which can be used to extract vectorial features and
creating vectorized drawing files for aerial photos. At the same time
a software developed for these purpose. Converting from raster to
vector is also known as vectorization and it is the most important step
when creating vectorized drawing files. In the developed algorithm,
first of all preprocessing on the aerial photo is done. These are;
converting to grayscale if necessary, reducing noise, applying some
filters and determining the edge of the objects etc. After these steps,
every pixel which constitutes the photo are followed from upper left
to right bottom by examining its neighborhood relationship and one
pixel wide lines or polylines obtained. The obtained lines have to be
erased for preventing confusion while continuing vectorization
because if not erased they can be perceived as new line, but if erased
it can cause discontinuity in vector drawing so the image converted
from 2 bit to 8 bit and the detected pixels are expressed as a different
bit. In conclusion, the aerial photo can be converted to vector form
which includes lines and polylines and can be opened in any CAD
application.
Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.
Abstract: The development of wearable sensing technologies is a great challenge which is being addressed by the Proetex FP6 project (www.proetex.org). Its main aim is the development of wearable sensors to improve the safety and efficiency of emergency personnel. This will be achieved by continuous, real-time monitoring of vital signs, posture, activity, and external hazards surrounding emergency workers. We report here the development of carbon dioxide (CO2) sensing boot by incorporating commercially available CO2 sensor with a wireless platform into the boot assembly. Carefully selected commercially available sensors have been tested. Some of the key characteristics of the selected sensors are high selectivity and sensitivity, robustness and the power demand. This paper discusses some of the results of CO2 sensor tests and sensor integration with wireless data transmission
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: The hybridization of artificial immune system with
cellular automata (CA-AIS) is a novel method. In this hybrid model,
the cellular automaton within each cell deploys the artificial immune
system algorithm under optimization context in order to increase its
fitness by using its neighbor-s efforts. The hybrid model CA-AIS is
introduced to fix the standard artificial immune system-s weaknesses.
The credibility of the proposed approach is evaluated by simulations
and it shows that the proposed approach achieves better results
compared to standard artificial immune system.
Abstract: In this paper, an Arabic letter recognition system based on Artificial Neural Networks (ANNs) and statistical analysis for feature extraction is presented. The ANN is trained using the Least Mean Squares (LMS) algorithm. In the proposed system, each typed Arabic letter is represented by a matrix of binary numbers that are used as input to a simple feature extraction system whose output, in addition to the input matrix, are fed to an ANN. Simulation results are provided and show that the proposed system always produces a lower Mean Squared Error (MSE) and higher success rates than the current ANN solutions.
Abstract: Frequently a group of people jointly decide and authorize
a specific person as a representative in some business/poitical
occasions, e.g., the board of a company authorizes the chief executive
officer to close a multi-billion acquisition deal. In this paper, an
integrated proxy multi-signature scheme that allows anonymously
vetoable delegation is proposed. This protocol integrates mechanisms
of private veto, distributed proxy key generation, secure transmission
of proxy key, and existentially unforgeable proxy multi-signature
scheme. First, a provably secure Guillou-Quisquater proxy signature
scheme is presented, then the “zero-sharing" protocol is extended
over a composite modulus multiplicative group, and finally the above
two are combined to realize the GQ proxy multi-signature with
anonymously vetoable delegation. As a proxy signature scheme, this
protocol protects both the original signers and the proxy signer.
The modular design allows simplified implementation with less
communication overheads and better computation performance than
a general secure multi-party protocol.
Abstract: Field experiments were carried out at Owo, southwest Nigeria to evaluate the effect of different tillage practices (zero tillage with mulch (ZTM), row tillage (RT) and conventional tillage (CT), and with or without oil palm bunch ash plus poultry manure (OBA+PM) on soil chemical properties, growth and yield of ginger. The experiment was laid out in a randomized complete plot design with three replications. Soil chemical properties, growth and fresh rhizome yield reduced with frequency/intensity of tillage imposed while application of OBA+PM increased them. Among the tillage practices, the highest fresh rhizome yield (15.0t ha-1) was produced by ZTM which was significantly different from other tillage practices. Among the tillage – OBA+PM combinations, the most satisfactorily yield (20.1t ha-1) was produced by ZTM+OBA+PM while the lowest yield (15.7t ha-1) was in CT+OBA+PM.
Abstract: In this study, a mathematical model was proposed and
the accuracy of this model was assessed to predict the growth of
Pseudomonas aeruginosa and rhamnolipid production under nitrogen
limiting (sodium nitrate) fed-batch fermentation. All of the
parameters used in this model were achieved individually without
using any data from the literature.
The overall growth kinetic of the strain was evaluated using a
dual-parallel substrate Monod equation which was described by
several batch experimental data. Fed-batch data under different
glycerol (as the sole carbon source, C/N=10) concentrations and feed
flow rates were used to describe the proposed fed-batch model and
other parameters. In order to verify the accuracy of the proposed
model several verification experiments were performed in a vast
range of initial glycerol concentrations. While the results showed an
acceptable prediction for rhamnolipid production (less than 10%
error), in case of biomass prediction the errors were less than 23%. It
was also found that the rhamnolipid production by P. aeruginosa was
more sensitive at low glycerol concentrations.
Based on the findings of this work, it was concluded that the
proposed model could effectively be employed for rhamnolipid
production by this strain under fed-batch fermentation on up to 80 g l-
1 glycerol.
Abstract: After the Terengganu state government decided to give a boost in teaching and learning through the allocation of free ebooks to all Primary five and six students; it was time to examine the presence of e-books in the classrooms. A survey was conducted on 101 students to determine how they felt about using the e-book and their experiences. It was discovered that a majority of these students liked using the e-book. However, although they had little problems using the e-book and the e-book helped to lighten the schoolbags, these new-age textbooks were not fully utilized. It is implied that perhaps the school administrators, teachers and students may not be able to overcome the unfamiliar characteristics of the e-book and its limitations.
Abstract: This paper describes a new method for affine parameter
estimation between image sequences. Usually, the parameter
estimation techniques can be done by least squares in a quadratic
way. However, this technique can be sensitive to the presence
of outliers. Therefore, parameter estimation techniques for various
image processing applications are robust enough to withstand the
influence of outliers. Progressively, some robust estimation functions
demanding non-quadratic and perhaps non-convex potentials adopted
from statistics literature have been used for solving these. Addressing
the optimization of the error function in a factual framework for
finding a global optimal solution, the minimization can begin with
the convex estimator at the coarser level and gradually introduce nonconvexity
i.e., from soft to hard redescending non-convex estimators
when the iteration reaches finer level of multiresolution pyramid.
Comparison has been made to find the performance of the results
of proposed method with the results found individually using two
different estimators.
Abstract: I/O workload is a critical and important factor to
analyze I/O pattern and file system performance. However tracing I/O
operations on the fly distributed parallel file system is non-trivial due
to collection overhead and a large volume of data. In this paper, we
design and implement a parallel file system logging method for high
performance computing using shared memory-based multi-layer
scheme. It minimizes the overhead with reduced logging operation
response time and provides efficient post-processing scheme through
shared memory. Separated logging server can collect sequential logs
from multiple clients in a cluster through packet communication.
Implementation and evaluation result shows low overhead and high
scalability of this architecture for high performance parallel logging
analysis.
Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.