Abstract: In this paper, we propose a routing scheme that guarantees
the residual lifetime of wireless sensor networks where each
sensor node operates with a limited budget of battery energy. The
scheme maximizes the communications QoS while sustaining the
residual battery lifetime of the network for a specified duration.
Communication paths of wireless nodes are translated into a directed
acyclic graph(DAG) and the maximum-flow algorithm is applied to
the graph. The found maximum flow are assigned to sender nodes, so
as to maximize their communication QoS. Based on assigned flows,
the scheme determines the routing path and the transmission rate of
data packet so that any sensor node on the path would not exhaust
its battery energy before a specified duration.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: The number of users supported in a DS-CDMA
cellular system is typically less than spreading factor (N), and the
system is said to be underloaded. Overloading is a technique to
accommodate more number of users than the spreading factor N. In
O/O overloading scheme, the first set is assigned to the N
synchronous users and the second set is assigned to the additional
synchronous users. An iterative multistage soft decision interference
cancellation (SDIC) receiver is used to remove high level of
interference between the two sets. Performance is evaluated in terms
of the maximum number acceptable users so that the system
performance is degraded slightly compared to the single user
performance at a specified BER. In this paper, the capacity of CDMA
based O/O overloading scheme is evaluated with SDIC receiver. It is
observed that O/O scheme using orthogonal Gold codes provides
25% channel overloading (N=64) for synchronous DS-CDMA
system on an AWGN channel in the uplink at a BER of 1e-5.For a
Rayleigh faded channel, the critical capacity is 40% at a BER of 5e-5
assuming synchronous users. But in practical systems, perfect chip
timing is very difficult to maintain in the uplink.. We have shown that
the overloading performance reduces to 11% for a timing
synchronization error of 0.02Tc for a BER of 1e-5.
Abstract: For the sensor network to operate successfully, the active nodes should maintain both sensing coverage and network connectivity. Furthermore, scheduling sleep intervals plays critical role for energy efficiency of wireless sensor networks. Traditional methods for sensor scheduling use either sensing coverage or network connectivity, but rarely both. In this paper, we use random scheduling for sensing coverage and then turn on extra sensor nodes, if necessary, for network connectivity. Simulation results have demonstrated that the number of extra nodes that is on with upper bound of around 9%, is small compared to the total number of deployed sensor nodes. Thus energy consumption for switching on extra sensor node is small.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.
Abstract: In general dynamic analyses, lower mode response is
of interest, however the higher modes of spatially discretized
equations generally do not represent the real behavior and not affects
to global response much. Some implicit algorithms, therefore, are
introduced to filter out the high-frequency modes using intended
numerical error. The objective of this study is to introduce the
P-method and PC α-method to compare that with dissipation method
and Newmark method through the stability analysis and numerical
example. PC α-method gives more accuracy than other methods
because it based on the α-method inherits the superior properties of the
implicit α-method. In finite element analysis, the PC α-method is more
useful than other methods because it is the explicit scheme and it
achieves the second order accuracy and numerical damping
simultaneously.
Abstract: In order to meet environmental norms, Indian fuel
policy aims at producing ultra low sulphur diesel (ULSD) in near
future. A catalyst for meeting such requirements has been developed
and kinetics of this catalytic process is being looked into. In the
present investigations, effect of mass transfer on kinetics of ultra deep
hydrodesulphurization (UDHDS) to produce ULSD has been studied
to determine intrinsic kinetics over a pre-sulphided catalyst.
Experiments have been carried out in a continuous flow micro reactor
operated in the temperature range of 330 to 3600C, whsv of 1 hr-1 at a
pressure of 35 bar, and its parameters estimated. Based on the derived
rate expression and estimated parameters optimum operation range
has been determined for this UDHDS catalyst to obtain ULSD
product.
Abstract: The aim of this paper is to investigate the
performance of the developed two point block method designed for
two processors for solving directly non stiff large systems of higher
order ordinary differential equations (ODEs). The method calculates
the numerical solution at two points simultaneously and produces
two new equally spaced solution values within a block and it is
possible to assign the computational tasks at each time step to a
single processor. The algorithm of the method was developed in C
language and the parallel computation was done on a parallel shared
memory environment. Numerical results are given to compare the
efficiency of the developed method to the sequential timing. For
large problems, the parallel implementation produced 1.95 speed-up
and 98% efficiency for the two processors.
Abstract: In this paper, we investigate a blind channel estimation method for Multi-carrier CDMA systems that use a subspace decomposition technique. This technique exploits the orthogonality property between the noise subspace and the received user codes to obtain channel of each user. In the past we used Singular Value Decomposition (SVD) technique but SVD have most computational complexity so in this paper use a new algorithm called URV Decomposition, which serve as an intermediary between the QR decomposition and SVD, replaced in SVD technique to track the noise space of the received data. Because of the URV decomposition has almost the same estimation performance as the SVD, but has less computational complexity.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: Wireless Sensor Network (WSN) comprises of sensor
nodes which are designed to sense the environment, transmit sensed
data back to the base station via multi-hop routing to reconstruct
physical phenomena. Since physical phenomena exists significant
overlaps between temporal redundancy and spatial redundancy, it is
necessary to use Redundancy Suppression Algorithms (RSA) for sensor
node to lower energy consumption by reducing the transmission
of redundancy. A conventional algorithm of RSAs is threshold-based
RSA, which sets threshold to suppress redundant data. Although
many temporal and spatial RSAs are proposed, temporal-spatial RSA
are seldom to be proposed because it is difficult to determine when
to utilize temporal or spatial RSAs. In this paper, we proposed a
novel temporal-spatial redundancy suppression algorithm, Codebookbase
Redundancy Suppression Mechanism (CRSM). CRSM adopts
vector quantization to generate a codebook, which is easily used to
implement temporal-spatial RSA. CRSM not only achieves power
saving and reliability for WSN, but also provides the predictability
of network lifetime. Simulation result shows that the network lifetime
of CRSM outperforms at least 23% of that of other RSAs.
Abstract: The entomopathogenic nematodes Steinernema
feltiaeare are components of many biological pesticides. The
biological pesticides are applicated by means a spraying machines.
The influence of high pressure operating time on viability of
nematodes has been experimentally investigated in order to explain if
static pressure inside of the sprayers installation was able to destroy
nematodes. The value of pressure was 55 MPa and its maximum
operating time was 3 hours. Changes were found in viability of
pressurized samples of nematodes, mixed with water.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: Wireless sensor networks (WSN) consists of many
sensor nodes that are placed on unattended environments such as
military sites in order to collect important information.
Implementing a secure protocol that can prevent forwarding forged
data and modifying content of aggregated data and has low delay
and overhead of communication, computing and storage is very
important. This paper presents a new protocol for concealed data
aggregation (CDA). In this protocol, the network is divided to
virtual cells, nodes within each cell produce a shared key to send
and receive of concealed data with each other. Considering to data
aggregation in each cell is locally and implementing a secure
authentication mechanism, data aggregation delay is very low and
producing false data in the network by malicious nodes is not
possible. To evaluate the performance of our proposed protocol, we
have presented computational models that show the performance
and low overhead in our protocol.
Abstract: The psychological well-being of a family is a subjective matter for evaluation, all the more when it involves the element of religions, whether Islam, Christianity, Buddhism or Hinduism. Each of these religions emphasises similar values and morals on family psychological well-being. This comparative study is specifically to determine the role of religion on family psychological well-being in Pekan district, Pahang, Malaysia. The study adopts a quantitative and qualitative mixed method design and considers a total of 412 samples of parents and children for the quantitative study, and 21 samples for the qualitative study. The quantitative study uses simple random sampling, whereas the qualitative sampling is purposive. The instrument for quantitative study is Ryff’s Psychological Well-being Scale and the qualitative study involves the construction of a guidelines protocol for in-depth interviews of respondents. The quantitative study uses the SPSS version .19 with One Way Anova, and the qualitative analysis is manual based on transcripts with specific codes and themes. The results show nonsignificance, that is, no significant difference among religions in all family psychological well-being constructs in the comparison of Islam, Christianity, Buddhism and Hinduism, thereby accepting a null hypothesis and rejecting an alternative hypothesis. The qualitative study supports the quantitative study, that is, all 21 respondents explain that no difference exists in psychological wellbeing in the comparison of teachings in all the religious mentioned. These implications may be used as guidelines for government and non-government bodies in considering religion as an important element in family psychological well-being in the long run.
Abstract: We present a visualization technique for radial drawing of trees consisting of two slightly different algorithms. Both of them make use of node-link diagrams for visual encoding. This visualization creates clear drawings without edge crossing. One of the algorithms is suitable for real-time visualization of large trees, as it requires minimal recalculation of the layout if leaves are inserted or removed from the tree; while the other algorithm makes better utilization of the drawing space. The algorithms are very similar and follow almost the same procedure but with different parameters. Both algorithms assign angular coordinates for all nodes which are then converted into 2D Cartesian coordinates for visualization. We present both algorithms and discuss how they compare to each other.
Abstract: In this paper, the application of the Mode Matching
(MM) method in the case of photonic crystal waveguide
discontinuities is presented. The structure under consideration is
divided into a number of cells, which supports a number of guided
and evanescent modes. These modes can be calculated numerically
by an alternative formulation of the plane wave expansion method
for each frequency. A matrix equation is then formed relating the
modal amplitudes at the beginning and at the end of the structure.
The theory is highly efficient and accurate and can be applied to
study the transmission sensitivity of photonic crystal devices due to
fabrication tolerances. The accuracy of the MM method is compared
to the Finite Difference Frequency Domain (FDFD) and the Adjoint
Variable Method (AVM) and good agreement is observed.