Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p
Abstract: This study was conducted to investigate the effect of
the antioxidant activity of germinated African Yam Bean (AYB) on
oxidative stress markers in alloxan induced diabetic rat. Rats were
randomized into three groups; control, diabetic and germinated AYB
– treated diabetic rats. The Total phenol and flavonoid content and
DPPH radical scavenging activity before and after germination were
investigated. The glucose level, lipid peroxidation and reduced
glutathione of the animals were also determined using standard
technique for four weeks. Germination increased the total phenol,
flavonoid and antioxidant activity of AYB extract by 19.14%,
32.28% and 57.25% respectively. The diabetic rats placed on
germinated AYB diet had a significant decrease in the blood glucose
and lipid peroxidation with a corresponding increase in glutathione
(p
Abstract: Thin ZnO films are deposited on glass substrates via
sol–gel method and dip-coating. The films are prepared from zinc
acetate dehydrate as a starting reagent. After that the as-prepared
ZnO sol is aged for different periods (0, 1, 3, 5, 10, 15 and 30 days).
Nanocrystalline thin films are deposited from various sols. The
effect ZnO sols aging time on the structural and photocatalytic
properties of the films is studied. The films surface is studied by
Scanning Electron Microscopy. The effect of the aging time of the
starting solution is studied in the photocatalytic degradation of
Reactive Black 5 (RB5) by UV-vis spectroscopy. The experiments
are conducted upon UV-light illumination and in complete darkness.
The variation of the absorption spectra shows the degradation of RB5
dissolved in water, as a result of the reaction, occurring on the surface
of the films and promoted by UV irradiation. The initial
concentrations of dye (5, 10 and 20 ppm) and the effect of the aging
time are varied during the experiments. The results show, that the
increasing aging time of starting solution with respect to ZnO
generally promotes photocatalytic activity. The thin films obtained
from ZnO sol, which is aged 30 days have best photocatalytic
degradation of the dye (97,22%) in comparison with the freshly
prepared ones (65,92%). The samples and photocatalytic
experimental results are reproducible. Nevertheless, all films exhibit
a substantial activity in both UV light and darkness, which is
promising for the development of new ZnO photocatalysts by sol-gel
method.
Abstract: The concept of urban transformation came about
through interventions aimed at bringing socially and economically
problematic areas of cities into use. The issue of urban transformation
arose frequently during the post-2000 period in particular, and legal
regulations on this matter were also developed in Turkey. Urban
transformation project would be a focal point for the formation of the
city in the near future. Izmir, which is third largest city of Turkey, is
an important trade and port city. But, assessment of the current
situation shows that, the majority of existing residential areas was
formed with squatters and unplanned settlements in Izmir city center.
Therefore an important part of these areas have significant problems
in terms of the quality of life, safety and environmental quality. In
this study, the central policies in Turkey and local policies in Đzmir
about urban transformation will be considered. In addition, urban
renewal projects that are being implemented in Izmir were discussed
and suggestions will be developed in accordance with this policy.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: This review emphasizes the effectiveness of men’s
participation in preventing domestic violence, and whether nonviolent
(NV) boys’ and men’s perceptions of intimate partner
violence (IPV) prevention programs affect their involvement. The
main goals of this assessment were to investigate (1) how NV men
engaged in anti-violence prevention programs that empower women,
(2) what were the possible perceptions of NV men involved in
prevention programs (3) how to identify effective approaches and
strategies that encouraged NV men to become involved in prevention
programs. This critical review also included the overview of
prevention programs such as: The Mentors in Violence Prevention
Programs (MVP), The White Ribbon Campaign (WRC), and
Domestic Violence Prevention Enhancement and Leadership through
Alliances (DELTA). The review suggested that (1) the expanding
prevention programs need to reach more macro settings such as work
place, faith-based and other community based organizations, and (2)
territory prevention programs should expand through addressing the
long-term effects of violence.
Abstract: Currently, there is excessively growing information
about places on Facebook, which is the largest social network but
such information is not explicitly organized and ranked. Therefore
users cannot exploit such data to recommend places conveniently and
quickly. This paper proposes a Facebook application and an Android
application that recommend places based on the number of check-ins
of those places, the distance of those places from the current location,
the number of people who like Facebook page of those places, and
the number of talking about of those places. Related Facebook data is
gathered via Facebook API requests. The experimental results of the
developed applications show that the applications can recommend
places and rank interesting places from the most to the least. We have
found that the average satisfied score of the proposed Facebook
application is 4.8 out of 5. The users’ satisfaction can increase by
adding the app features that support personalization in terms of
interests and preferences.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: A compact UWB planar antenna fed with a
microstrip-line is proposed. The new design consist of a rectangular
patch with symmetric l-shaped slots and fed by 50 Ω microstrip
transmission line and a reduced ground-plane which have a periodic
slots with an overall size of 47 mm x 20 mm. It is intended to be used
in wireless applications that cover the ultra-wideband (UWB)
frequency band. A wider impedance bandwidth of around 116.5%
(1.875 – 7.115 GHz) with stable radiation pattern is achieved. The
proposed antenna has excellent characteristics, low profile and costeffective
compared to existing UWB antennas. The UWB antenna is
designed and analyzed using CST Microwave Studio in transient
mode to verify antenna parameters improvements.
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: The use of information tools is a common activity for
students of any educational stage when they encounter online
learning activities. Finding the relevant information for particular
learning tasks is the topic of this paper as it investigates the use of
information tools for a group of student participants. The paper
describes and discusses the results with particular implications for
use in higher education, and the findings suggest that improvement in
assessment design and subsequent student learning may be achieved
by structuring the purposefulness of information tools usage and
online reading behaviors of university students.
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: In this paper, the effect of grades 32.4 and 42.5
Portland-limestone cements generally used for concrete production in
Nigeria on concrete compressive strength is investigated.
Investigation revealed that the compressive strength of concrete
produced with Portland-limestone cement grade 42.5 is generally
higher than that produced with cement grade 32.5. The percentage
difference between the compressive strengths of the concrete cubes
produced with Portland-limestone cement grades 42.5 and 32.5 is
inversely proportional to the richness of the concrete with the highest
and the least percentage difference associated with the 1:2:4 and
1:1:2 mix ratios respectively. It is recommended that cement grade
42.5 be preferred for construction in Nigeria as this will lead to the
construction of stronger concrete structures, which will reduce the
incidence of failure of building and other concrete structures at no
additional cost since the cost of both cement grades are the same.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: The use OF adhesive anchors for wooden constructions is an efficient technology to connect and design timber members in new timber structures and to rehabilitate the damaged structural members of historical buildings. Due to the lack of standard regulation in this specific area of structural design, designers’ choices are still supported by test analysis that enables knowledge, and the prediction, of the structural behaviour of glued in rod joints. The paper outlines an experimental research activity aimed at identifying the tensile resistance capacity of several new adhesive joint prototypes made of epoxy resin, steel bar and timber, Oak and Douglas Fir species. The development of new adhesive connectors has been carried out by using epoxy to glue stainless steel bars into pre-drilled holes, characterised by smooth and rough internal surfaces, in timber samples. The realization of a threaded contact surface using a specific drill bit has led to an improved bond between wood and epoxy. The applied changes have also reduced the cost of the joints’ production. The paper presents the results of this parametric analysis and a Finite Element analysis that enables identification and study of the internal stress distribution in the proposed adhesive anchors.
Abstract: One image is worth more than thousand words.
Images if analyzed can reveal useful information. Low level image
processing deals with the extraction of specific feature from a single
image. Now the question arises: What technique should be used to
extract patterns of very large and detailed image database? The
answer of the question is: “Image Mining”. Image Mining deals with
the extraction of image data relationship, implicit knowledge, and
another pattern from the collection of images or image database. It is
nothing but the extension of Data Mining. In the following paper, not
only we are going to scrutinize the current techniques of image
mining but also present a new technique for mining images using
Genetic Algorithm.
Abstract: This paper presents an adaptive thermal comfort
model study in the tropical country of Malaysia. A number of
researchers have been interested in applying the adaptive thermal
comfort model to different climates throughout the world, but so far
no study has been performed in Malaysia. For the use as a thermal
comfort model, which better applies to hot and humid climates, the
adaptive thermal comfort model was developed as part of this
research by using the collected results from a large field study in six
lecture halls with 178 students. The relationship between the
operative temperature and behavioral adaptations was determined. In
the developed adaptive model, the acceptable indoor neutral
temperatures lay within the range of 23.9-26.0C, with outdoor
temperatures ranging between 27.0-34.6C. The most comfortable
temperature for students in lecture hall was 25.7C.
Abstract: In this letter, we explore exact solutions for the
Horava-Lifshitz gravity. We use of an extension of this theory with
first order dynamical lapse function. The equations of motion have
been derived in a fully consistent scenario. We assume that there
are some spherically symmetric families of exact solutions of this
extended theory of gravity. We obtain exact solutions and investigate
the singularity structures of these solutions. Specially, an exact
solution with the regular horizon is found.