Abstract: In this paper we develop an efficient numerical method for the finite-element model updating of damped gyroscopic systems based on incomplete complex modal measured data. It is assumed that the analytical mass and stiffness matrices are correct and only the damping and gyroscopic matrices need to be updated. By solving a constrained optimization problem, the optimal corrected symmetric damping matrix and skew-symmetric gyroscopic matrix complied with the required eigenvalue equation are found under a weighted Frobenius norm sense.
Abstract: Due to the three- dimensional flow pattern interacting with bed material, the process of local scour around bridge piers is complex. Modeling 3D flow field and scour hole evolution around a bridge pier is more feasible nowadays because the computational cost and computational time have significantly decreased. In order to evaluate local flow and scouring around a bridge pier, a completely three-dimensional numerical model, SSIIM program, was used. The model solves 3-D Navier-Stokes equations and a bed load conservation equation. The model was applied to simulate local flow and scouring around a bridge pier in a large natural river with four piers. Computation for 1 day of flood condition was carried out to predict the maximum local scour depth. The results show that the SSIIM program can be used efficiently for simulating the scouring in natural rivers. The results also showed that among the various turbulence models, the k-ω model gives more reasonable results.
Abstract: This experiment was carried out to study the effect of
AMF, drought stress and phosphorus on physiological growth indices of basil at Iran using by a split-plot design with three replications.
The main-plot factor included: two levels of irrigation regimes (control=no drought stress and irrigation after 80 evaporation=
drought stress condition) while the sub-plot factors included
phosphorus (0, 35 and 70 kg/ha) and application and non-application of Glomus fasciculatum. The results showed that total dry matter
(TDM), life area index (LAI), relative growth rate (RGR) and crop growth rate (CGR) were all highly significantly different among the
phosphorus, whereas drought stress had effect of practical
significance on TDM, LAI, RGR and CGR. The results also showed that the highest TDM, LAI, RGR and CGR were obtained from
application of Glomus fasciculatum under no-drought condition.
Abstract: This study proposes a basic molecular formula for all
proteins. A total of 10,739 proteins belonging to 9 different protein
groups classified on the basis of their functions were selected
randomly. They included enzymes, storage proteins, hormones,
signalling proteins, structural proteins, transport proteins,
immunoglobulins or antibodies, motor proteins and receptor proteins.
After obtaining the protein molecular formula using the ProtParam
tool, the H/C, N/C, O/C, and S/C ratios were determined for each
randomly selected sample. In this case, H, N, O, and S coefficients
were specified per carbon atom. Surprisingly, the results
demonstrated that H, N, O, and S coefficients for all 10,739 proteins
are similar and highly correlated. This study demonstrates that
despite differences in the structure and function, all known proteins
have a similar basic molecular formula CnH1.58 ± 0.015nN0.28 ± 0.005nO0.30
± 0.007nS0.01 ± 0.002n. The total correlation between all coefficients was
found to be 0.9999.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.
Abstract: This paper presents the solution of power economic dispatch (PED) problem of generating units with valve point effects and multiple fuel options using Self-Adaptive Differential Evolution (SDE) algorithm. The global optimal solution by mathematical approaches becomes difficult for the realistic PED problem in power systems. The Differential Evolution (DE) algorithm is found to be a powerful evolutionary algorithm for global optimization in many real problems. In this paper the key parameters of control in DE algorithm such as the crossover constant CR and weight applied to random differential F are self-adapted. The PED problem formulation takes into consideration of nonsmooth fuel cost function due to valve point effects and multi fuel options of generator. The proposed approach has been examined and tested with the numerical results of PED problems with thirteen-generation units including valve-point effects, ten-generation units with multiple fuel options neglecting valve-point effects and ten-generation units including valve-point effects and multiple fuel options. The test results are promising and show the effectiveness of proposed approach for solving PED problems.
Abstract: The main aim is to perform mutational analysis of CTLA4 gene Exon 1 in SLE patients. A total of 61 SLE patients fulfilling “American College of Rheumatology (ACR) criteria" and 61 controls were enrolled in this study. The region of CTLA4 gene exon 1 was amplified by using Step-down PCR technique. Extracted DNA of band 354 bp was sequenced to analyze mutations in the exon-1 of CTLA-4 gene. Further, protein sequences were identified from nucleotide sequences of CTLA4 Exon 1 by using Expasy software and through Blast P software it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. No variations were found after patients sequences were compared with that of the control sequence. Furthermore it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. Thus CTLA4 gene may not be responsible for an autoimmune disease SLE.
Abstract: The study investigated the hydrophilic to hydrophobic
transition of modified polyacrylamide hydrogel with the inclusion of
N-isopropylacrylamide (NIAM). The modification was done by
mimicking micellar polymerization, which resulted in better
arrangement of NIAM chains in the polyacrylamide network. The
degree of NIAM arrangement is described by NH number. The
hydrophilic to hydrophobic transition was measured through the
partition coefficient, K, of Orange II and Methylene Blue in hydrogel
and in water. These dyes were chosen as a model for solutes with
different degree of hydrophobicity. The study showed that the
hydrogel with higher NH values resulted in better solubility of both
dyes. Moreover, in temperature above the lower critical solution
temperature (LCST) of Poly(N-isopropylacrylamide) (PNIAM)also
caused the collapse of NIPAM chains which results in a more
hydrophobic environment that increases the solubility of Methylene
Blue and decreases the solubility of Orange II in the hydrogels with
NIPAM present.
Abstract: A techno-economic evaluation for efficient use of
energy in a large scale industrial plant of methanol is carried out.
This assessment is based on integration of a gas turbine with an
existing plant of methanol in which the outlet gas products of
exothermic reactor is expanded to power generation. Also, it is
decided that methanol production rate is constant through addition of
power generation system to the existing methanol plant. Having
incorporated a gas turbine with the existing plant, the economic
results showed total investment of MUSD 16.9, energy saving of 3.6
MUSD/yr with payback period of approximately 4.7 years.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.
Abstract: We measured the major and trace element contents
and Rb-Sr isotopic compositions of 12 tektites from the Maoming
area, Guandong province (south China). All the samples studied are
splash-form tektites which show pitted or grooved surfaces with
schlieren structures on some surfaces. The trace element ratios Ba/Rb
(avg. 4.33), Th/Sm (avg. 2.31), Sm/Sc (avg. 0.44), Th/Sc (avg. 1.01) ,
La/Sc (avg. 2.86), Th/U (avg. 7.47), Zr/Hf (avg. 46.01) and the rare
earth elements (REE) contents of tektites of this study are similar to the
average upper continental crust. From the chemical composition, it is
suggested that tektites in this study are derived from similar parental
terrestrial sedimentary deposit which may be related to post-Archean
upper crustal rocks. The tektites from the Maoming area have high
positive εSr(0) values-ranging from 176.9~190.5 which indicate that
the parental material for these tektites have similar Sr isotopic
compositions to old terrestrial sedimentary rocks and they were not
dominantly derived from recent young sediments (such as soil or
loess). The Sr isotopic data obtained by the present study support the
conclusion proposed by Blum et al. (1992)[1] that the depositional age
of sedimentary target materials is close to 170Ma (Jurassic). Mixing
calculations based on the model proposed by Ho and Chen (1996)[2]
for various amounts and combinations of target rocks indicate that the
best fit for tektites from the Maoming area is a mixture of 40% shale,
30% greywacke, 30% quartzite.
Abstract: This article is devoted to the analysis of results of
sociological researches carried out by authors directed on studying of
opinion of representatives of small, medium and big business on
formation of the Customs Union, Common Free Market Zone with
participation of Kazakhstan, Russia and Belarus.
It-s forecasted that companies, their branches will interpenetrate
with registration and moving their businesses to regions with more
beneficial conditions. They say that in Kazakhstan there are more
profitable geo-strategic operating environment for business and lower
taxes. Russia using this opportunity will create new conditions for
expansion into other countries of Central Asia and China. Opinions
of participants of questionnaire and expert poll different in estimation
of value of these two integration mechanisms since market segments
on the one hand extend, but also on the other hand - loss of exclusive
influence in certain fields of activity.
Abstract: In this paper, a study on the modes of collapse of
compress- expand members are presented. Compress- expand member
is a compact, multiple-combined cylinders, to be proposed as energy
absorbers. Previous studies on the compress- expand member have
clarified its energy absorption efficiency, proposed an approximate
equation to describe its deformation characteristics and also
highlighted the improvement that it has brought. However, for the
member to be practical, the actual range of geometrical dimension that
it can maintain its applicability must be investigated. In this study,
using a virtualized materials that comply the bilinear hardening law,
Finite element Method (FEM) analysis on the collapse modes of
compress- expand member have been conducted. Deformation maps
that plotted the member's collapse modes with regards to the member's
geometric and material parameters were then presented in order to
determine the dimensional range of each collapse modes.
Abstract: In this paper, based on a novel synthesis, a set of new simplified circuit design to implement the linguistic-hedge operations for adjusting the fuzzy membership function set is presented. The circuits work in current-mode and employ floating-gate MOS (FGMOS) transistors that operate in weak inversion region. Compared to the other proposed circuits, these circuits feature severe reduction of the elements number, low supply voltage (0.7V), low power consumption (60dB). In this paper, a set of fuzzy linguistic hedge circuits, including absolutely, very, much more, more, plus minus, more or less and slightly, has been implemented in 0.18 mm CMOS process. Simulation results by Hspice confirm the validity of the proposed design technique and show high performance of the circuits.
Abstract: The effect of porous medium on the capillary instability of a cylindrical interface in the presence of axial electric field has been investigated using viscous potential flow theory. In viscous potential flow, the viscous term in Navier-Stokes equation vanishes as
vorticity is zero but viscosity is not zero. Viscosity enters through normal stress balance in the viscous potential flow theory and tangential stresses are not considered. A dispersion relation that accounts for the growth of axisymmetric waves is derived and stability is discussed theoretically as well as numerically. Stability criterion is given by critical value of applied electric field as well as critical wave number. Various graphs have been drawn to show the effect of various physical parameters such as electric field, viscosity ratio, permittivity ratio on the stability of the system. It has been observed that the axial electric field and porous medium both have stabilizing effect on the stability of the system.
Abstract: This paper presents the analysis of duct design using
static and dynamic approaches. The static approach is used to find
out applicability between the design and material applied. The
material used in this paper is Thermoplastic Olefins (TPO). For the
dynamic approach, the focusing is only on the CFD simulations. The
fatigue life in this design and material applied also covered.
Abstract: Nowadays, biometrical characterizations of Artemia
cysts are used as one of the most important factors in the study of
Artemia populations and intraspecific particularity; meanwhile these
characters can be used as economical indices. For example, typically
high hatching efficiency is possible due to the small diameter of
cysts (high number per gram); therefore small diameter of cysts
show someway high quality of cysts. This study was performed
during a ten year period, including two different ecological
conditions: rainy and drought. It is important from two different
aspects because it covers alteration of A. urmiana during ten years
also its variation in the best and worst environmental situations in
which salinity increased from 173.8 ppt in 1994 to 280.8 ppt in
2003/4. In this study the biometrical raw data of Artemia urmiana
cysts at seven stations from the Urmia Lake in 1994 and their seven
identical locations at 26 studied stations in 2003/4 were reanalyzed
again and compared together. Biometrical comparison of untreated
and decapsulated cysts in each of the seven similar stations showed a
highly significant variation between 1994 and 2003/4. Based on this
study, in whole stations the untreated and decapsulated cysts from
1994 were larger than cysts of 2003/4 without any exception. But
there was no logical relationship between salinity and chorion
thickness in the Urmia Lake. With regard to PCA analyses the
stations of two different studied years certainly have been separated
with factor 1 from each other. In conclusion, the interaction between
genetic and environmental factors can determine and explain
variation in the range of cysts diameter in Artemia.
Abstract: The method of modeling is the key technology for
digital mockup (DMU). Based upon the developing for mechanical
product DMU, the theory, method and approach for virtual
environment (VE) and virtual object (VO) were studied. This paper
has expounded the design goal and architecture of DMU system,
analyzed the method of DMU application, and researched the general
process of physics modeling and behavior modeling.
Abstract: Computerized lip reading has been one of the most
actively researched areas of computer vision in recent past because
of its crime fighting potential and invariance to acoustic environment.
However, several factors like fast speech, bad pronunciation,
poor illumination, movement of face, moustaches and beards make
lip reading difficult. In present work, we propose a solution for
automatic lip contour tracking and recognizing letters of English
language spoken by speakers using the information available from
lip movements. Level set method is used for tracking lip contour
using a contour velocity model and a feature vector of lip movements
is then obtained. Character recognition is performed using modified
k nearest neighbor algorithm which assigns more weight to nearer
neighbors. The proposed system has been found to have accuracy
of 73.3% for character recognition with speaker lip movements as
the only input and without using any speech recognition system in
parallel. The approach used in this work is found to significantly
solve the purpose of lip reading when size of database is small.