Abstract: In this paper, an optimal design of linear phase digital
high pass finite impulse response (FIR) filter using Particle Swarm
Optimization with Constriction Factor and Inertia Weight Approach
(PSO-CFIWA) has been presented. In the design process, the filter
length, pass band and stop band frequencies, feasible pass band and
stop band ripple sizes are specified. FIR filter design is a multi-modal
optimization problem. The conventional gradient based optimization
techniques are not efficient for digital filter design. Given the filter
specifications to be realized, the PSO-CFIWA algorithm generates a
set of optimal filter coefficients and tries to meet the ideal frequency
response characteristic. In this paper, for the given problem, the
designs of the optimal FIR high pass filters of different orders have
been performed. The simulation results have been compared to those
obtained by the well accepted algorithms such as Parks and
McClellan algorithm (PM), genetic algorithm (GA). The results
justify that the proposed optimal filter design approach using PSOCFIWA
outperforms PM and GA, not only in the accuracy of the
designed filter but also in the convergence speed and solution
quality.
Abstract: In neural networks, when new patterns are learned by a network, the new information radically interferes with previously stored patterns. This drawback is called catastrophic forgetting or catastrophic interference. In this paper, we propose a biologically inspired neural network model which overcomes this problem. The proposed model consists of two distinct networks: one is a Hopfield type of chaotic associative memory and the other is a multilayer neural network. We consider that these networks correspond to the hippocampus and the neocortex of the brain, respectively. Information given is firstly stored in the hippocampal network with fast learning algorithm. Then the stored information is recalled by chaotic behavior of each neuron in the hippocampal network. Finally, it is consolidated in the neocortical network by using pseudopatterns. Computer simulation results show that the proposed model has much better ability to avoid catastrophic forgetting in comparison with conventional models.
Abstract: Accurate modeling of high speed RLC interconnects
has become a necessity to address signal integrity issues in current
VLSI design. To accurately model a dispersive system of interconnects
at higher frequencies; a full-wave analysis is required.
However, conventional circuit simulation of interconnects with full
wave models is extremely CPU expensive. We present an algorithm
for reducing large VLSI circuits to much smaller ones with similar
input-output behavior. A key feature of our method, called Frequency
Shift Technique, is that it is capable of reducing linear time-varying
systems. This enables it to capture frequency-translation and sampling
behavior, important in communication subsystems such as mixers,
RF components and switched-capacitor filters. Reduction is obtained
by projecting the original system described by linear differential
equations into a lower dimension. Experiments have been carried out
using Cadence Design Simulator cwhich indicates that the proposed
technique achieves more % reduction with less CPU time than the
other model order reduction techniques existing in literature. We
also present applications to RF circuit subsystems, obtaining size
reductions and evaluation speedups of orders of magnitude with
insignificant loss of accuracy.
Abstract: Multiple-input multiple-output (MIMO) systems are
widely in use to improve quality, reliability of wireless transmission
and increase the spectral efficiency. However in MIMO systems,
multiple copies of data are received after experiencing various
channel effects. The limitations on account of complexity due to
number of antennas in case of conventional decoding techniques have
been looked into. Accordingly we propose a modified sphere decoder
(MSD-1) algorithm with lower complexity and give rise to system
with high spectral efficiency. With the aim to increase signal
diversity we apply rotated quadrature amplitude modulation (QAM)
constellation in multi dimensional space. Finally, we propose a new
architecture involving space time trellis code (STTC) concatenated
with space time block code (STBC) using MSD-1 at the receiver for
improving system performance. The system gains have been verified
with channel state information (CSI) errors.
Abstract: The growth of open networks created the interest to
commercialise it. The establishment of an electronic business
mechanism must be accompanied by a digital – electronic payment
system to transfer the value of transactions. Financial organizations
are requested to offer a secure e-payment synthesis with equivalent
level of security served in conventional paper-based payment
transactions. PKI, which is functioning as a chain of trust in security
architecture, can enable security services of cryptography to epayments,
in order to take advantage of the wider base either of
customer or of trading partners and the reduction of cost transaction
achieved by the use of Internet channels. The paper addresses the
possibilities and the implementation suggestions of PKI in relevance
to electronic payments by suggesting a framework that should be
followed.
Abstract: This paper describes the use of artificial neural
networks (ANN) for predicting non-linear layer moduli of flexible
airfield pavements subjected to new generation aircraft (NGA)
loading, based on the deflection profiles obtained from Heavy
Weight Deflectometer (HWD) test data. The HWD test is one of the
most widely used tests for routinely assessing the structural integrity
of airport pavements in a non-destructive manner. The elastic moduli
of the individual pavement layers backcalculated from the HWD
deflection profiles are effective indicators of layer condition and are
used for estimating the pavement remaining life. HWD tests were
periodically conducted at the Federal Aviation Administration-s
(FAA-s) National Airport Pavement Test Facility (NAPTF) to
monitor the effect of Boeing 777 (B777) and Beoing 747 (B747) test
gear trafficking on the structural condition of flexible pavement
sections. In this study, a multi-layer, feed-forward network which
uses an error-backpropagation algorithm was trained to approximate
the HWD backcalculation function. The synthetic database generated
using an advanced non-linear pavement finite-element program was
used to train the ANN to overcome the limitations associated with
conventional pavement moduli backcalculation. The changes in
ANN-based backcalculated pavement moduli with trafficking were
used to compare the relative severity effects of the aircraft landing
gears on the NAPTF test pavements.
Abstract: This paper presents a SCR-based ESD protection devices for I/O clamp and power rail clamp, respectably. These devices have a low trigger voltage and high holding voltage characteristics than conventional SCR device. These devices are fabricated by using 0.35um BCD (Bipolar-CMOS-DMOS) processes. These devices were validated using a TLP system. From the experimental results, the device for I/O ESD clamp has a trigger voltage of 5.8V. Also, the device for power rail ESD clamp has a holding voltage of 7.7V.
Abstract: In this paper, we propose a fast and efficient method for drawing very large-scale graph data. The conventional force-directed method proposed by Fruchterman and Rheingold (FR method) is well-known. It defines repulsive forces between every pair of nodes and attractive forces between connected nodes on a edge and calculates corresponding potential energy. An optimal layout is obtained by iteratively updating node positions to minimize the potential energy. Here, the positions of the nodes are updated every global timestep at the same time. In the proposed method, each node has its own individual time and time step, and nodes are updated at different frequencies depending on the local situation. The proposed method is inspired by the hierarchical individual time step method used for the high accuracy calculations for dense particle fields such as star clusters in astrophysical dynamics. Experiments show that the proposed method outperforms the original FR method in both speed and accuracy. We implement the proposed method on the MDGRAPE-3 PCI-X special purpose parallel computer and realize a speed enhancement of several hundred times.
Abstract: The objective of this study was to develop vaginal
suppository containing lactobacillus. Four kinds of vaginal
suppositories containing Lactobacillus paracasei HL32 were
formulated: 1) a conventional suppository with Witepsol H-15 as a
base, 2) a conventional suppository with mixed polyethylene glycols
(PEGs) as a base, 3) a hollow-type suppository with Witepsol H-15
as a base and 4) a hollow-type suppository with mixed PEGs as a
base. The release studies demonstrated that the hollow-type
suppository with mixed PEGs as the base gave the highest release of
L. paracasei HL32 and was microbiological stable after storage at 2-
8°C over the period of 3 months.
Abstract: Optimal supplementary damping controller design for Thyristor Controlled Series Compensator (TCSC) is presented in this paper. For the proposed controller design, a multi-objective fitness function consisting of both damping factors and real part of system electromachanical eigenvalue is used and Real- Coded Genetic Algorithm (RCGA) is employed for the optimal supplementary controller parameters. The performance of the designed supplementary TCSC-based damping controller is tested on a weakly connected power system with different disturbances and loading conditions with parameter variations. Simulation results are presented and compared with a conventional power system stabilizer and also with the TCSC-based supplementary controller when the controller parameters are not optimized to show the effectiveness and robustness of the proposed approach over a wide range of loading conditions and disturbances.
Abstract: In order to enhance the contrast in the regions where the pixels have similar intensities, this paper presents a new histogram equalization scheme. Conventional global equalization schemes over-equalizes these regions so that too bright or dark pixels are resulted and local equalization schemes produce unexpected discontinuities at the boundaries of the blocks. The proposed algorithm segments the original histogram into sub-histograms with reference to brightness level and equalizes each sub-histogram with the limited extents of equalization considering its mean and variance. The final image is determined as the weighted sum of the equalized images obtained by using the sub-histogram equalizations. By limiting the maximum and minimum ranges of equalization operations on individual sub-histograms, the over-equalization effect is eliminated. Also the result image does not miss feature information in low density histogram region since the remaining these area is applied separating equalization. This paper includes how to determine the segmentation points in the histogram. The proposed algorithm has been tested with more than 100 images having various contrasts in the images and the results are compared to the conventional approaches to show its superiority.
Abstract: Iron in groundwater is one of the problems that render the water unsuitable for drinking. The concentration above 0.3 mg/L is common in groundwater. The conventional method of removal is by precipitation under oxic condition. In this study, iron removal under anaerobic conditions was examined by batch experiment as a main purpose. The process involved by purging of groundwater samples with H2S to form iron sulfide. Removal up to 83% for 1 mg/L iron solution was achieved. The removal efficiency dropped to 82% and 75% for the higher initial iron concentrations 3.55 and 5.01 mg/L, respectively. The average residual sulfide concentration in water after the process was 25*g/L. The Eh level during the process was -272 mV. The removal process was found to follow the first order reaction with average rate constant of 4.52 x 10-3. The half-life for the concentrations to reduce from initial values was 157 minutes.
Abstract: This paper introduces a novel design for boring bar with enhanced damping capability. The principle followed in the design phase was to enhance the damping capability minimizing the loss in static stiffness through implementation of composite material interfaces. The newly designed tool has been compared to a conventional tool. The evaluation criteria were the dynamic characteristics, frequency and damping ratio, of the machining system, as well as the surface roughness of the machined workpieces. The use of composite material in the design of damped tool has been demonstrated effective. Furthermore, the autoregressive moving average (ARMA) models presented in this paper take into consideration the interaction between the elastic structure of the machine tool and the cutting process and can therefore be used to characterize the machining system in operational conditions.
Abstract: Experiments were carried out at the Latvia State
Institute of Fruit-Growing in 2011. Fresh-cut minimally processed
apple and pear mixed salad were packed by passive modified
atmosphere (MAP) in PP containers, which were hermetically sealed
by breathable conventional BOPP PropafreshTM P2GAF, and Amcor
Agrifresh films. Biodegradable NatureFlexTM NVS INNOVIA Films
and VC999 BioPack PLA films coated with a barrier of pure silicon
oxide (SiOx) were used to compare the fresh-cut produce quality
with this packed in conventional packaging films. Samples were cold
stored at temperature +4.0±0.5 °C up to 10 days. The quality of salad
was evaluated by physicochemical properties – weight losses,
moisture, firmness, the effect of packaging modes on the colour,
dynamics in headspace atmosphere concentration (CO2 and O2),
titratable acidity values, as well as by microbiological contamination
(yeasts, moulds and total bacteria count) of salads, analyzing before
packaging and after 2, 4, 6, 8, and 10 storage days.
Abstract: Cytogenetic analysis still remains the gold standard method for prenatal diagnosis of trisomy 21 (Down syndrome, DS). Nevertheless, the conventional cytogenetic analysis needs live cultured cells and is too time-consuming for clinical application. In contrast, molecular methods such as FISH, QF-PCR, MLPA and quantitative Real-time PCR are rapid assays with results available in 24h. In the present study, we have successfully used a novel MGB TaqMan probe-based real time PCR assay for rapid diagnosis of trisomy 21 status in Down syndrome samples. We have also compared the results of this molecular method with corresponding results obtained by the cytogenetic analysis. Blood samples obtained from DS patients (n=25) and normal controls (n=20) were tested by quantitative Real-time PCR in parallel to standard G-banding analysis. Genomic DNA was extracted from peripheral blood lymphocytes. A high precision TaqMan probe quantitative Real-time PCR assay was developed to determine the gene dosage of DSCAM (target gene on 21q22.2) relative to PMP22 (reference gene on 17p11.2). The DSCAM/PMP22 ratio was calculated according to the formula; ratio=2 -ΔΔCT. The quantitative Real-time PCR was able to distinguish between trisomy 21 samples and normal controls with the gene ratios of 1.49±0.13 and 1.03±0.04 respectively (p value
Abstract: In this paper a new fast simplification method is
presented. Such method realizes Karnough map with large
number of variables. In order to accelerate the operation of the
proposed method, a new approach for fast detection of group
of ones is presented. Such approach implemented in the
frequency domain. The search operation relies on performing
cross correlation in the frequency domain rather than time one.
It is proved mathematically and practically that the number of
computation steps required for the presented method is less
than that needed by conventional cross correlation. Simulation
results using MATLAB confirm the theoretical computations.
Furthermore, a powerful solution for realization of complex
functions is given. The simplified functions are implemented
by using a new desigen for neural networks. Neural networks
are used because they are fault tolerance and as a result they
can recognize signals even with noise or distortion. This is
very useful for logic functions used in data and computer
communications. Moreover, the implemented functions are
realized with minimum amount of components. This is done
by using modular neural nets (MNNs) that divide the input
space into several homogenous regions. Such approach is
applied to implement XOR function, 16 logic functions on one
bit level, and 2-bit digital multiplier. Compared to previous
non- modular designs, a clear reduction in the order of
computations and hardware requirements is achieved.
Abstract: AAM has been successfully applied to face alignment,
but its performance is very sensitive to initial values. In case the initial
values are a little far distant from the global optimum values, there
exists a pretty good possibility that AAM-based face alignment may
converge to a local minimum. In this paper, we propose a progressive
AAM-based face alignment algorithm which first finds the feature
parameter vector fitting the inner facial feature points of the face and
later localize the feature points of the whole face using the first
information. The proposed progressive AAM-based face alignment
algorithm utilizes the fact that the feature points of the inner part of the
face are less variant and less affected by the background surrounding
the face than those of the outer part (like the chin contour). The
proposed algorithm consists of two stages: modeling and relation
derivation stage and fitting stage. Modeling and relation derivation
stage first needs to construct two AAM models: the inner face AAM
model and the whole face AAM model and then derive relation matrix
between the inner face AAM parameter vector and the whole face
AAM model parameter vector. In the fitting stage, the proposed
algorithm aligns face progressively through two phases. In the first
phase, the proposed algorithm will find the feature parameter vector
fitting the inner facial AAM model into a new input face image, and
then in the second phase it localizes the whole facial feature points of
the new input face image based on the whole face AAM model using
the initial parameter vector estimated from using the inner feature
parameter vector obtained in the first phase and the relation matrix
obtained in the first stage. Through experiments, it is verified that the
proposed progressive AAM-based face alignment algorithm is more
robust with respect to pose, illumination, and face background than the
conventional basic AAM-based face alignment algorithm.
Abstract: In this study, a fuzzy integrated logical forecasting method (FILF) is extended for multi-variate systems by using a vector autoregressive model. Fuzzy time series forecasting (FTSF) method was recently introduced by Song and Chissom [1]-[2] after that Chen improved the FTSF method. Rather than the existing literature, the proposed model is not only compared with the previous FTS models, but also with the conventional time series methods such as the classical vector autoregressive model. The cluster optimization is based on the C-means clustering method. An empirical study is performed for the prediction of the chartering rates of a group of dry bulk cargo ships. The root mean squared error (RMSE) metric is used for the comparing of results of methods and the proposed method has superiority than both traditional FTS methods and also the classical time series methods.
Abstract: The paper presents a space-vector pulse width modulation (SVPWM) inverter feeding a permanent-magnet synchronous motor (PMSM). The SVPWM inverter enables to feed the motor with a higher voltage with low harmonic distortions than the conventional sinusoidal PWM inverter. The control strategy of the inverter is the voltage / frequency control method, which is based on the space-vector modulation technique. The proposed PMSM drive system involving the field-oriented control scheme not only decouples the torque and flux which provides faster response but also makes the control task easy. The performance of the proposed drive is simulated. The advantages of the proposed drive are confirmed by the simulation results.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.