Abstract: Multiple Sclerosis (MS) is a disease which affects the
central nervous system and causes balance problem. In clinical, this
disorder is usually evaluated using static posturography. Some linear
or nonlinear measures, extracted from the posturographic data (i.e.
center of pressure, COP) recorded during a balance test, has been
used to analyze postural control of MS patients. In this study, the
trend (TREND) and the sample entropy (SampEn), two nonlinear
parameters were chosen to investigate their relationships with the
expanded disability status scale (EDSS) score. 40 volunteers with
different EDSS scores participated in our experiments with eyes open
(EO) and closed (EC). TREND and 2 types of SampEn (SampEn1
and SampEn2) were calculated for each combined COP’s position
signal. The results have shown that TREND had a weak negative
correlation to EDSS while SampEn2 had a strong positive correlation
to EDSS. Compared to TREND and SampEn1, SampEn2 showed a
better significant correlation to EDSS and an ability to discriminate
the MS patients in the EC case. In addition, the outcome of the study
suggests that the multi-dimensional nonlinear analysis could provide
some information about the impact of disability progression in MS on
dynamics of the COP data.
Abstract: The paper focuses on the distance laboratory
organisation for training the electrical engineering staff and students
in the fields of electrical drive and power electronics. To support
online knowledge acquisition and professional enhancement, new
challenges in remote education based on an active learning approach
with self-assessment have been emerged by the authors. Following
the literature review and explanation of the improved assessment
methodology, the concept and technological basis of the labs
arrangement are presented. To decrease the gap between the distance
study of the up-to-date equipment and other educational activities in
electrical engineering, the improvements in the following-up the
learners’ progress and feedback composition are introduced. An
authoring methodology that helps to personalise knowledge
acquisition and enlarge Web-based possibilities is described.
Educational management based on self-assessment is discussed.
Abstract: Holistic methods covering the development process as
a whole – e.g. systems engineering – have established themselves in
product design. However, technical product optimization,
representing improvements in efficiency and/or minimization of loss,
usually applies to single components of a system. A holistic approach
is being defined based on a hierarchical point of view of systems
engineering. This is subsequently presented using the example of an
electromechanical flywheel energy storage system for automotive
applications.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: Maintenance and design engineers have great concern
for the functioning of rotating machineries due to the vibration
phenomenon. Improper functioning in rotating machinery originates
from the damage to rolling element bearings. The status of rolling
element bearings require advanced technologies to monitor their
health status efficiently and effectively. Avoiding vibration during
machine running conditions is a complicated process. Vibration
simulation should be carried out using suitable sensors/ transducers to
recognize the level of damage on bearing during machine operating
conditions. Various issues arising in rotating systems are interlinked
with bearing faults. This paper presents an approach for fault
diagnosis of bearings using neural networks and time/frequencydomain
vibration analysis.
Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: Rapid developments in technology in the present age
have made it necessary for communities to follow technological
developments and adapt themselves to these developments. One of
the fields that are most rapidly affected by these developments is
undoubtedly education. Determination of the attitudes of preservice
teachers, who live in an age of technology and get ready to raise
future individuals, is of paramount importance both educationally and
professionally. The purpose of this study was to analyze attitudes of
preservice teachers towards technology and some variables that
predict these attitudes (gender, daily duration of internet use, and the
number of technical devices owned). 329 preservice teachers
attending the education faculty of a large university in central Turkey
participated, on a volunteer basis, in this study, where relational
survey model was used as the research method. Research findings
reveal that preservice teachers’ attitudes towards technology are
positive and at the same time, the attitudes of male preservice
teachers towards technology are more positive than their female
counterparts. As a result of the stepwise multiple regression analysis
where factors predicting preservice teachers’ attitudes towards
technology, it was found that duration of daily internet use was the
strongest predictor of attitudes towards technology.
Abstract: The aim of this work is to study the numerical
implementation of the Hilbert Uniqueness Method for the exact
boundary controllability of Euler-Bernoulli beam equation. This study
may be difficult. This will depend on the problem under consideration
(geometry, control and dimension) and the numerical method used.
Knowledge of the asymptotic behaviour of the control governing the
system at time T may be useful for its calculation. This idea will
be developed in this study. We have characterized as a first step, the
solution by a minimization principle and proposed secondly a method
for its resolution to approximate the control steering the considered
system to rest at time T.
Abstract: Over the last two decades, externally bonded fiber
reinforced polymer (FRP) composites bonded to concrete substrates
has become a popular method for strengthening reinforced concrete
(RC) highway and railway bridges. Such structures are exposed to
severe cyclic loading throughout their lifetime often resulting in
fatigue damage to structural components and a reduction in the
service life of the structure. Since experimental and numerical results
on the fatigue performance of FRP-to-concrete joints are still limited,
the current research focuses on assessing the fatigue performance of
externally bonded FRP-to-concrete joints using a direct shear test.
Some early results indicate that the stress ratio and the applied cyclic
stress level have a direct influence on the fatigue life of the externally
bonded FRP. In addition, a calibrated finite element model is
developed to provide further insight into the influence of certain
parameters such as: concrete strength, FRP thickness, number of
cycles, frequency, and stiffness on the fatigue life of the FRP-toconcrete
joints.
Abstract: Green and renewable energy is getting extraordinary
consideration today, because of ecological concerns made by blazing
of fossil powers. Photovoltaic and wind power generation are the
basic decisions for delivering power in this respects. Producing
power by the sun based photovoltaic systems is known to the world,
yet control makers may get confounded to pick between on-grid and
off-grid systems. In this exploration work, an endeavor is made to
compare the off-grid (stand-alone) and on-grid (grid-connected)
frameworks. The work presents relative examination, between two
distinctive PV frameworks situated at V.V.P. Engineering College,
Rajkot. The first framework is 100 kW remain solitary and the
second is 60 kW network joined. The real-time parameters compared
are; output voltage, load current, power in-flow, power output,
performance ratio, yield factor, and capacity factor. The voltage
changes and the power variances in both frameworks are given
exceptional consideration and the examination is made between the
two frameworks to judge the focal points and confinements of both
the frameworks.
Abstract: Cadmium oxide (CdO) nanoparticles have been
prepared by chemical coprecipitation method. The synthesized
nanoparticles were characterized by X-ray diffraction analysis
(XRD), scanning electron microscopy (SEM), transmission electron
microscopy (TEM), UV analysis, and dielectric studies. The
crystalline nature and particle size of the CdO nanoparticles were
characterized by Powder X-ray diffraction analysis (XRD). The
morphology of prepared CdO nanoparticles was studied by scanning
electron microscopy. The particle size was studied using the
transmission electron microscopy (TEM).The optical properties were
obtained from UV-Vis absorption spectrum. The dielectric properties
of CdO nanoparticles were studied in the frequency range of 50 Hz–5
MHz at different temperatures. The frequency dependence of the
dielectric constant and dielectric loss is found to decrease with an
increase in the frequency at different temperatures. The ac
conductivity of CdO nanoparticle has been studied.
Abstract: Inspired by the Formula-1 competition, IMechE
(Institute of Mechanical Engineers) and Formula SAE (Society of
Mechanical Engineers) organize annual competitions for University
and College students worldwide to compete with a single-seat racecar
they have designed and built. Design of the chassis or the frame is a
key component of the competition because the weight and stiffness
properties are directly related with the performance of the car and the
safety of the driver. In addition, a reduced weight of the chassis has
direct influence on the design of other components in the car. Among
others, it improves the power to weight ratio and the aerodynamic
performance. As the power output of the engine or the battery
installed in the car is limited to 80 kW, increasing the power to
weight ratio demands reduction of the weight of the chassis, which
represents the major part of the weight of the car. In order to reduce
the weight of the car, ION Racing team from University of
Stavanger, Norway, opted for a monocoque design. To ensure
fulfilment of the competition requirements of the chassis, the
monocoque design should provide sufficient torsional stiffness and
absorb the impact energy in case of possible collision. The study reported in this article is based on the requirements for
Formula Student competition. As part of this study, diverse
mechanical tests were conducted to determine the mechanical
properties and performances of the monocoque design. Upon a
comprehensive theoretical study of the mechanical properties of
sandwich composite materials and the requirements of monocoque
design in the competition rules, diverse tests were conducted
including 3-point bending test, perimeter shear test and test for
absorbed energy. The test panels were homemade and prepared with
equivalent size of the side impact zone of the monocoque, i.e. 275
mm x 500 mm, so that the obtained results from the tests can be
representative. Different layups of the test panels with identical core
material and the same number of layers of carbon fibre were tested
and compared. Influence of the core material thickness was also
studied. Furthermore, analytical calculations and numerical analysis
were conducted to check compliance to the stated rules for Structural
Equivalency with steel grade SAE/AISI 1010. The test results were
also compared with calculated results with respect to bending and
torsional stiffness, energy absorption, buckling, etc. The obtained results demonstrate that the material composition
and strength of the composite material selected for the monocoque
design has equivalent structural properties as a welded frame and thus
comply with the competition requirements. The developed analytical
calculation algorithms and relations will be useful for future
monocoque designs with different lay-ups and compositions.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: Common Platform for Automated Programming
(CPAP) is defined in details. Two versions of CPAP are described:
Cloud based (including set of components for classic programming,
and set of components for combined programming); and Knowledge
Based Automated Software Engineering (KBASE) based (including
set of components for automated programming, and set of
components for ontology programming). Four KBASE products
(Module for Automated Programming of Robots, Intelligent Product
Manual, Intelligent Document Display, and Intelligent Form
Generator) are analyzed and CPAP contributions to automated
programming are presented.
Abstract: In the past years electric mobility became part of a
public discussion. The trend to fully electrified vehicles instead of
vehicles fueled with fossil energy has notably gained momentum.
Today nearly every big car manufacturer produces and sells fully
electrified vehicles, but electrified vehicles are still not as competitive
as conventional powered vehicles. As the traction battery states the
largest cost driver, lowering its price is a crucial objective. In
addition to improvements in product and production processes a nonnegligible,
but widely underestimated cost driver of production can
be found in logistics, since the production technology is not
continuous yet and neither are the logistics systems. This paper presents an approach to evaluate cost factors on
different designs of load carrier systems. Due to numerous
interdependencies, the combination of costs factors for a particular
scenario is not transparent. This is effecting actions for cost reduction
negatively, but still cost reduction is one of the major goals for
simultaneous engineering processes. Therefore a concurrent and
phase appropriate cost valuation method is necessary to serve cost
transparency. In this paper the four phases of this cost valuation
method are defined and explained, which based upon a new approach
integrating the logistics development process in to the integrated
product and process development.
Abstract: Response Surface Methods (RSM) provide
statistically validated predictive models that can then be manipulated
for finding optimal process configurations. Variation transmitted to
responses from poorly controlled process factors can be accounted
for by the mathematical technique of propagation of error (POE),
which facilitates ‘finding the flats’ on the surfaces generated by
RSM. The dual response approach to RSM captures the standard
deviation of the output as well as the average. It accounts for
unknown sources of variation. Dual response plus propagation of
error (POE) provides a more useful model of overall response
variation. In our case, we implemented this technique in predicting
compressive strength of concrete of 28 days in age. Since 28 days is
quite time consuming, while it is important to ensure the quality
control process. This paper investigates the potential of using design
of experiments (DOE-RSM) to predict the compressive strength of
concrete at 28th day. Data used for this study was carried out from
experiment schemes at university of Benghazi, civil engineering
department. A total of 114 sets of data were implemented. ACI mix
design method was utilized for the mix design. No admixtures were
used, only the main concrete mix constituents such as cement, coarseaggregate,
fine aggregate and water were utilized in all mixes.
Different mix proportions of the ingredients and different water
cement ratio were used. The proposed mathematical models are
capable of predicting the required concrete compressive strength of
concrete from early ages.
Abstract: Job satisfaction and motivation have been given an
important attention in psychology because they are seen as main
instruments in maintaining organizational growth and development;
they are also used to accomplish organizational aims and objectives.
However, it has been observed that some institutions failed in
motivating and stimulating their workers; in contrast, workers may be
motivated but not satisfied with the job and failed to perform
efficiently and effectively. It is hoped that the study of this nature
would be of significance value to all stakeholders in education
specifically, lecturers in higher institutions in Nigeria. Also, it is
hoped that the findings of this study will enhance lecturers’
effectiveness and performance in discharging their duties. In the light
of the above statements, this study investigated whether job
satisfaction and motivation predict lecturers’ effectiveness in Nigeria
Police Academy, Wudil, Kano State. Correlational research method
was adopted for the study, while purposive sampling technique was
used to choose the institution and the sampled lectures (70). Simple
random sampling technique was used to select one hundred cadets
across the academy. Two instruments were used to elicit information
from both lecturers and cadets. These were job satisfaction and
motivation; and lecturers’ effectiveness Questionnaires. The
instruments were subjected to pilot testing and found to have
reliability coefficient of 0.69 and 0.71 respectively. The results of the
study revealed that there was a significance relationship among job
satisfaction, motivation and lecturers effectiveness in Nigeria Police
Academy. There was a significance relationship between job
satisfaction and lecturers’ effectiveness in Nigeria Police Academy
the cal r is 0.21 while the crt r is 0.19. at p
Abstract: This paper introduces a signal monitoring program
developed with a view to helping electrical engineering students get
familiar with sensors with digital output. Because the output of digital
sensors cannot be simply monitored by a measuring instrument such as
an oscilloscope, students tend to have a hard time dealing with digital
sensors. The monitoring program runs on a PC and communicates with
an MCU that reads the output of digital sensors via an asynchronous
communication interface. Receiving the sensor data from the MCU,
the monitoring program shows time and/or frequency domain plots of
the data in real time. In addition, the monitoring program provides a
serial terminal that enables the user to exchange text information with
the MCU while the received data is plotted. The user can easily
observe the output of digital sensors and configure the digital sensors
in real time, which helps students who do not have enough experiences
with digital sensors. Though the monitoring program was programmed
in the Matlab programming language, it runs without the Matlab since
it was compiled as a standalone executable.