Abstract: Gilaburu (Viburnum opulus L.) grown naturally in
Anatolia. In this study, some physico-chemical (sugar, acid, protein,
crude fat, crude fiber, ash etc.) characteristics and mineral
composition of Gilaburu fruit have been investigated. The length,
width, thickness, weight, total soluble solid, protein, crude ash, crude
fiber and crude oil of fruit were found to be 1.12 cm, 1.58 cm, 1.87
cm, 0.87 g, 14.73 %, 0.2 %, 0.11 %, 6.56 % and 0.4 %, respectively.
The seed of fruit mean weight, length, width and thickness were
determinated as 0.08 g, 7.76 cm, 7.67 cm and 1.66, respectively. In
addition 27 mineral elements (Al, Mg, Na, Ba, Ca, Ni, Cd, P, Cr, Pb,
S, Cu, Se, Fe, K, Sr, Li, Z, V, Ag, Bi, Co, Mn, B, Ga, In, Ti) were
analyzed. Gilaburu (Viburnum opulus L.) fruit was richest in
potassium (10764.764 ppm), Mg (1289.088 ppm) and P (1304.169
ppm).
Abstract: A Cable-Driven Locomotion Interface provides a low
inertia haptic interface and is used as a way of enabling the user
to walk and interact with virtual surfaces. These surfaces generate
Cartesian wrenches which must be optimized for each motorized
reel in order to reproduce a haptic sensation in both feet. However,
the use of wrench control requires a measure of the cable tensions
applied to the moving platform. The latter measure may be inaccurate
if it is based on sensors located near the reel. Moreover, friction
hysteresis from the reel moving parts needs to be compensated
for with an evaluation of low angular velocity of the motor shaft.
Also, the pose of the platform is not known precisely due to cable
sagging and mechanical deformation. This paper presents a non-ideal
motorized reel design with its corresponding control strategy that
aims at overcoming the aforementioned issues. A transfert function
of the reel based on frequency responses in function of cable tension
and cable length is presented with an optimal adaptative PIDF
controller. Finally, an hybrid position/tension control is discussed with
an analysis of the stability for achieving a complete functionnality of
the haptic platform.
Abstract: Hydrogen sulfide (H2S) is a very toxic gas that is produced in very large quantities in the oil and gas industry. It cannot be flared to the atmosphere and Claus process based gas plants are used to recover the sulfur and convert the hydrogen to water. In this paper, we present optical characterization of an atmospheric pressure microwave plasma torch for H2S dissociation into hydrogen and sulfur. The torch is operated at 2.45 GHz with power up to 2 kW. Three different gases can simultaneously be injected in the plasma torch. Visual imaging and optical emission spectroscopy are used to characterize the plasma for varying gas flow rates and microwave power. The plasma length, emission spectra and temperature are presented. The obtained experimental results validate our earlier published simulation results of plasma torch.
Abstract: Horizontal wells are proven to be better producers
because they can be extended for a long distance in the pay zone.
Engineers have the technical means to forecast the well productivity
for a given horizontal length. However, experiences have shown that
the actual production rate is often significantly less than that of
forecasted. It is a difficult task, if not impossible to identify the real
reason why a horizontal well is not producing what was forecasted.
Often the source of problem lies in the drilling of horizontal section
such as permeability reduction in the pay zone due to mud invasion
or snaky well patterns created during drilling. Although drillers aim
to drill a constant inclination hole in the pay zone, the more frequent
outcome is a sinusoidal wellbore trajectory. The two factors, which
play an important role in wellbore tortuosity, are the inclination and
side force at bit. A constant inclination horizontal well can only be
drilled if the bit face is maintained perpendicular to longitudinal axis
of bottom hole assembly (BHA) while keeping the side force nil at
the bit. This approach assumes that there exists no formation force at
bit. Hence, an appropriate BHA can be designed if bit side force and
bit tilt are determined accurately. The Artificial Neural Network
(ANN) is superior to existing analytical techniques. In this study, the
neural networks have been employed as a general approximation tool
for estimation of the bit side forces. A number of samples are
analyzed with ANN for parameters of bit side force and the results
are compared with exact analysis. Back Propagation Neural network
(BPN) is used to approximation of bit side forces. Resultant low
relative error value of the test indicates the usability of the BPN in
this area.
Abstract: Experiments were carried out on the survival and growth of Rasbora daniconius, Puntius ticto and Puntius conchonius. The motivation of the study was to obtain information for growing the fish on a commercial scale for their use as biological control agents against mosquito larvae. The effects of temperature, total hardness, DO, pH and feed on the growth of fish were also investigated. Excessive value of total hardness was found because very rich calcium ion is present in Chitrakoot area. There was significant increases in growth rates of fish as temperature was increased from 280C to 300C. Further increases in temperature up to 320C, did not further affect growth. The positive and highly significant correlations 0.991488, 0.9581 and 0.9935 were found between length and weight of P. ticto, P. conchonius and R. daniconius respectively. The regression was significant at 5% level of probability.
Abstract: This paper proposes an efficient finite precision block floating point (BFP) treatment to the fixed coefficient finite impulse response (FIR) digital filter. The treatment includes effective implementation of all the three forms of the conventional FIR filters, namely, direct form, cascaded and par- allel, and a roundoff error analysis of them in the BFP format. An effective block formatting algorithm together with an adaptive scaling factor is pro- posed to make the realizations more simple from hardware view point. To this end, a generic relation between the tap weight vector length and the input block length is deduced. The implementation scheme also emphasises on a simple block exponent update technique to prevent overflow even during the block to block transition phase. The roundoff noise is also investigated along the analogous lines, taking into consideration these implementational issues. The simulation results show that the BFP roundoff errors depend on the sig- nal level almost in the same way as floating point roundoff noise, resulting in approximately constant signal to noise ratio over a relatively large dynamic range.
Abstract: High building constructions are increasing in south
beaches of the Caspian Sea because of tourist attractions and limitation of residential areas. According to saturated alluvial fields transfer of load from high structures to the soil by piles is inevitable.
In spite of most of these piles are under compression forces, tension piles are used in special conditions. Few studies have been conducted
because of the limited use of these piles. Tension capacity of openended pipe piles in full scale was tested in this study. The length of the bored piles was 420 up to 480 cm and all were in 120 cm
diameter. The results of testing 7 piles were compared with the results of relations given by researches.
Abstract: Both image steganography and image encryption have
advantages and disadvantages. Steganograhy allows us to hide a
desired image containing confidential information in a covered or
host image while image encryption is decomposing the desired image
to a non-readable, non-comprehended manner. The encryption
methods are usually much more robust than the steganographic ones.
However, they have a high visibility and would provoke the attackers
easily since it usually is obvious from an encrypted image that
something is hidden! The combination of steganography and
encryption will cover both of their weaknesses and therefore, it
increases the security. In this paper an image encryption method
based on sinc-convolution along with using an encryption key of 128
bit length is introduced. Then, the encrypted image is covered by a
host image using a modified version of JSteg steganography
algorithm. This method could be applied to almost all image formats
including TIF, BMP, GIF and JPEG. The experiment results show
that our method is able to hide a desired image with high security and
low visibility.
Abstract: Plant tissue culture is an important in vitro technology applied for agricultural and industrial production. A sterile condition of culture medium is one of the main aspects. The alternative technique for medium sterilization to replace autoclaving was carried out. For sterilization of plant tissue culture medium without autoclaving, ten commercial pure essential oils and 5 disinfectants were tested. Each essential oil or disinfectant was added to a 20-mL Murashige and Skoog (MS) medium before medium was solidified in a 120-mL container, kept for 2 weeks before evaluating sterile conditions. Treated media, supplemented with essential oils or disinfectants, were compared to control medium, autoclaved at 121 degree Celsius for 15 min. Sterile conditions of MS medium were found 100% from betel oil or clove oil (18 mL/20 mL medium), cinnamon oil (36 mL/20 mL medium), lavender oil or holy basil oil (108 mL/20 mL medium), and lemon oil or tea tree oil or turmeric oil (252 mL/20 mL medium), compared to 100% sterile condition from autoclaved medium. For disinfectants, 2% iodine + 2.4% potassium iodide, 2% merbromine solution, 10% povidone-iodine, 6% sodium hypochlorite or 0.1% thimerosal at 36 mL/20 mL medium provided 100% sterile conditions. Furthermore, growth of new shoots from chrysanthemum node explants on treated media (fresh weight, shoot length, root length and number of node) were also reported and discussed in the comparison of those on autoclaved medium.
Abstract: The InAlGaN alloy has only recently began receiving
serious attention into its growth and application. High quality InGaN
films have led to the development of light emitting diodes (LEDs) and
blue laser diodes (LDs). The quaternary InAlGaN however, represents
a more versatile material since the bandgap and lattice constant can be
independently varied. We report an ultraviolet (UV) quaternary
InAlGaN multi-quantum wells (MQWs) LD study by using the
simulation program of Integrated System Engineering (ISE TCAD).
Advanced physical models of semiconductor properties were used in
order to obtain an optimized structure. The device performance which
is affected by piezoelectric and thermal effects was studied via
drift-diffusion model for carrier transport, optical gain and loss. The
optical performance of the UV LD with different numbers of quantum
wells was numerically investigated. The main peak of the emission
wavelength for double quantum wells (DQWs) was shifted from 358
to 355.8 nm when the forward current was increased. Preliminary
simulated results indicated that better output performance and lower
threshold current could be obtained when the quantum number is four,
with output power of 130 mW and threshold current of 140 mA.
Abstract: In the context of spectrum surveillance, a new method
to recover the code of spread spectrum signal is presented, while the
receiver has no knowledge of the transmitter-s spreading sequence. In
our previous paper, we used Genetic algorithm (GA), to recover
spreading code. Although genetic algorithms (GAs) are well known
for their robustness in solving complex optimization problems, but
nonetheless, by increasing the length of the code, we will often lead
to an unacceptable slow convergence speed. To solve this problem we
introduce Particle Swarm Optimization (PSO) into code estimation in
spread spectrum communication system. In searching process for
code estimation, the PSO algorithm has the merits of rapid
convergence to the global optimum, without being trapped in local
suboptimum, and good robustness to noise. In this paper we describe
how to implement PSO as a component of a searching algorithm in
code estimation. Swarm intelligence boasts a number of advantages
due to the use of mobile agents. Some of them are: Scalability, Fault
tolerance, Adaptation, Speed, Modularity, Autonomy, and
Parallelism. These properties make swarm intelligence very attractive
for spread spectrum code estimation. They also make swarm
intelligence suitable for a variety of other kinds of channels. Our
results compare between swarm-based algorithms and Genetic
algorithms, and also show PSO algorithm performance in code
estimation process.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: In this paper a special kind of buffer management policy is studied where the packet are preempted even when sufficient space is available in the buffer for incoming packets. This is done to congestion for future incoming packets to improve QoS for certain type of packets. This type of study has been done in past for ATM type of scenario. We extend the same for heterogeneous traffic where data rate and size of the packets are very versatile in nature. Typical example of this scenario is the buffer management in Differentiated Service Router. There are two aspects that are of interest. First is the packet size: whether all packets have same or different sizes. Second aspect is the value or space priority of the packets, do all packets have the same space priority or different packets have different space priorities. We present two types of policies to achieve QoS goals for packets with different priorities: the push out scheme and the expelling scheme. For this work the scenario of packets of variable length is considered with two space priorities and main goal is to minimize the total weighted packet loss. Simulation and analytical studies show that, expelling policies can outperform the push out policies when it comes to offering variable QoS for packets of two different priorities and expelling policies also help improve the amount of admissible load. Some other comparisons of push out and expelling policies are also presented using simulations.
Abstract: This paper presents unified theory for local (Savitzky-
Golay) and global polynomial smoothing. The algebraic framework
can represent any polynomial approximation and is seamless from
low degree local, to high degree global approximations. The representation
of the smoothing operator as a projection onto orthonormal
basis functions enables the computation of: the covariance matrix
for noise propagation through the filter; the noise gain and; the
frequency response of the polynomial filters. A virtually perfect Gram
polynomial basis is synthesized, whereby polynomials of degree
d = 1000 can be synthesized without significant errors. The perfect
basis ensures that the filters are strictly polynomial preserving. Given
n points and a support length ls = 2m + 1 then the smoothing
operator is strictly linear phase for the points xi, i = m+1. . . n-m.
The method is demonstrated on geometric surfaces data lying on an
invariant 2D lattice.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: Recent research on seeds of bio-diesel plants like
Jatropha curcas, constituting 40-50% bio-crude oil indicates its
potential as one of the most promising alternatives to conventional
sources of energy. Also, limited studies on utilization of de-oiled cake
have revealed that Jatropha bio-waste has good potential to be used as
organic fertilizers produced via aerobic and anaerobic treatment.
However, their commercial exploitation has not yet been possible. The
present study aims at developing appropriate bio-processes and
formulations utilizing Jatropha seed cake as organic fertilizer, for
improving the growth of Polianthes tuberose L. (Tuberose). Pot
experiments were carried out by growing tuberose plants on soil
treated with composted formulations of Jatropha de-oiled cake, Farm
Yard Manure (FYM) and inorganic fertilizers were also blended in
soil. The treatment was carried out through soil amendment as well as
foliar spray. The growth and morphological parameters were
monitored for entire crop cycle.
The growth Length and number of leaves, spike length, rachis
length, number of bulb per plant and earliness of sprouting of bulb and
yield enhancement were comparable to that achieved under inorganic
fertilizer. Furthermore, performance of inorganic fertilizer also showed
an improvement when blended with composted bio-waste. These
findings would open new avenues for Jatropha based bio-wastes to be
composted and used as organic fertilizers for commercial floriculture.
Abstract: We present a novel construction of 16-QAM codewords of length n = 2k . The number of constructed codewords is 162×[4k-1×k-k+1] . When these constructed codewords are utilized as a code in OFDM systems, their peak-to-mean envelope power ratios (PMEPR) are bounded above by 3.6 . The principle of our scheme is illustrated with a four subcarrier example.
Abstract: The influence of twist arrangement on the temperature
distribution in an annular diffuser fitted with twisted rectangular hub
is investigated. Different pitches (Y = 120 mm, 100 mm, 80 mm, and
60 mm) for the twist arrangements are simulated to be compared. The
geometry of the annular diffuser and the inlet condition for the hub
arrangements are kept constant. The result reveals that using twisted
rectangular hub insert with different pitches will force the
temperature to distribute in a circular direction. However,
temperature distribution will be enhanced with the length pitch
increases.