Abstract: In the present work, the finite element formulation for
the investigation of the effects of a localized interfacial degeneration
on the dynamic behavior of the [90°/0°] laminated composite plate
employing the state-space technique is performed. The stiffness of
the laminate is determined by assembling the stiffnesses of subelements.
This includes an introduction of an interface layer adopting
the virtually zero-thickness formulation to model the interfacial
degeneration. Also, the kinematically consistent mass matrix and
proportional damping have been formulated to complete the free
vibration governing expression. To simulate the interfacial
degeneration of the laminate, the degenerated areas are defined from
the center propagating outwards in a localized manner. It is found
that the natural frequency, damped frequency and damping ratio of
the plate decreases as the degenerated area of the interface increases.
On the contrary, the loss factor increases correspondingly.
Abstract: Drying behavior of blanched sweet potato in a cabinet
dryer using different five air temperatures (40-80°C) and ten sweet
potato varieties sliced to 5mm thickness were investigated. The
drying data were fitted to eight models. The Modified Henderson and
Pabis model gave the best fit to the experimental moisture ratio data
obtained during the drying of all the varieties while Newton (Lewis)
and Wang and Singh models gave the least fit. The values of Deff
obtained for Bophelo variety (1.27 x 10-9 to 1.77 x 10-9 m2/s) was
the least while that of S191 (1.93 x 10-9 to 2.47 x 10-9 m2/s) was the
highest which indicates that moisture diffusivity in sweet potato is
affected by the genetic factor. Activation energy values ranged from
0.27-6.54 kJ/mol. The lower activation energy indicates that drying
of sweet potato slices requires less energy and is hence a cost and
energy saving method. The drying behavior of blanched sweet potato
was investigated in a cabinet dryer. Drying time decreased
considerably with increase in hot air temperature. Out of the eight
models fitted, the Modified Henderson and Pabis model gave the best
fit to the experimental moisture ratio data on all the varieties while
Newton, Wang and Singh models gave the least. The lower activation
energy (0.27 - 6.54 kJ/mol) obtained indicates that drying of sweet
potato slices requires less energy and is hence a cost and energy
saving method.
Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value
Abstract: We introduced an all-optical multicasting
characteristics with wavelength conversion based on a novel
all-optical triode using negative feedback semiconductor optical
amplifier. This study was demonstrated with a transfer speed of 10
Gb/s to a non-return zero 231-1 pseudorandom bit sequence system.
This multi-wavelength converter device can simultaneously provide
three channels of output signal with the support of non-inverted and
inverted conversion. We studied that an all-optical multicasting and
wavelength conversion accomplishing cross gain modulation is
effective in a semiconductor optical amplifier which is effective to
provide an inverted conversion thus negative feedback. The
relationship of received power of back to back signal and output
signals with wavelength 1535 nm, 1540 nm, 1545 nm, 1550 nm, and
1555 nm with bit error rate was investigated. It was reported that the
output signal wavelengths were successfully converted and modulated
with a power penalty of less than 8.7 dB, which the highest is 8.6 dB
while the lowest is 4.4 dB. It was proved that all-optical multicasting
and wavelength conversion using an optical triode with a negative
feedback by three channels at the same time at a speed of 10 Gb/s is a
promising device for the new wavelength conversion technology.
Abstract: GRF, Growth regulating factor, genes encode a novel
class of plant-specific transcription factors. The GRF proteins play a
role in the regulation of cell numbers in young and growing tissues
and may act as transcription activations in growth and development
of plants. Identification of GRF genes and their expression are
important in plants to performance of the growth and development of
various organs. In this study, to better understanding the structural
and functional differences of GRFs family, 45 GRF proteins
sequences in A. thaliana, Z. mays, O. sativa, B. napus, B. rapa, H.
vulgare and S. bicolor, have been collected and analyzed through
bioinformatics data mining. As a result, in secondary structure of
GRFs, the number of alpha helices was more than beta sheets and in
all of them QLQ domains were completely in the biggest alpha helix.
In all GRFs, QLQ and WRC domains were completely protected
except in AtGRF9. These proteins have no trans-membrane domain
and due to have nuclear localization signals act in nuclear and they
are component of unstable proteins in the test tube.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.
Abstract: This study is purposed to develop an efficient fault
detection method for Global Navigation Satellite Systems (GNSS)
applications based on adaptive noise covariance estimation. Due to the
dependence on radio frequency signals, GNSS measurements are
dominated by systematic errors in receiver’s operating environment.
In the proposed method, the pseudorange and carrier-phase
measurement noise covariances are obtained at time propagations and
measurement updates in process of Carrier-Smoothed Code (CSC)
filtering, respectively. The test statistics for fault detection are
generated by the estimated measurement noise covariances. To
evaluate the fault detection capability, intentional faults were added to
the filed-collected measurements. The experiment result shows that
the proposed method is efficient in detecting unhealthy measurements
and improves GNSS positioning accuracy against fault occurrences.
Abstract: One of the most important tasks in the risk
management is the correct determination of probability of default
(PD) of particular financial subjects. In this paper a possibility of
determination of financial institution’s PD according to the creditscoring
models is discussed. The paper is divided into the two parts.
The first part is devoted to the estimation of the three different
models (based on the linear discriminant analysis, logit regression
and probit regression) from the sample of almost three hundred US
commercial banks. Afterwards these models are compared and
verified on the control sample with the view to choose the best one.
The second part of the paper is aimed at the application of the chosen
model on the portfolio of three key Czech banks to estimate their
present financial stability. However, it is not less important to be able
to estimate the evolution of PD in the future. For this reason, the
second task in this paper is to estimate the probability distribution of
the future PD for the Czech banks. So, there are sampled randomly
the values of particular indicators and estimated the PDs’ distribution,
while it’s assumed that the indicators are distributed according to the
multidimensional subordinated Lévy model (Variance Gamma model
and Normal Inverse Gaussian model, particularly). Although the
obtained results show that all banks are relatively healthy, there is
still high chance that “a financial crisis” will occur, at least in terms
of probability. This is indicated by estimation of the various quantiles
in the estimated distributions. Finally, it should be noted that the
applicability of the estimated model (with respect to the used data) is
limited to the recessionary phase of the financial market.
Abstract: In the second decade of the XXI century the role of
tourism destination attractiveness is becoming increasingly important
for destination management. Competition in tourism market moves
from ordinary service quality to provision of unforgettable emotional
experience for tourists. The main purpose of the present study is to
identify the perception of the tourism destinations based on the
number of factors related to its tourist attractiveness.
The content analysis method was used to analyze the on-line
tourist feedback data immensely available in Social Media and in
travel related sites. The collected data made it possible to procure the
information which is necessary to understand the perceived
attractiveness of the destinations and key destination appeal factors
that are important for Russian leisure travelers.
Results of the present study demonstrate key attractiveness factors
or destination ‘properties’ that were unveiled as the most important
for Russian leisure tourists. The study targeted five main Spanish
tourism destinations that initially were determined by in-depth
interview with a number of Russian nationals who had visited Spain
at least once.
The research results can be useful for Spanish Tourism
Organization Representation office in Russia as well as for the other
national tourism organizations in order to promote their respective
destinations for Russian travelers focusing on main attractiveness
factors identified in this study.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: Climate change will affect the hydrological cycle in
many different ways such as increase in evaporation and rainfalls.
There have been growing interests among researchers to identify the
nature of trends in historical rainfall data in many different parts of
the world. This paper examines the trends in annual maximum
rainfall data from 30 stations in New South Wales, Australia by using
two non-parametric tests, Mann-Kendall (MK) and Spearman’s Rho
(SR). Rainfall data were analyzed for fifteen different durations
ranging from 6 min to 3 days. It is found that the sub-hourly
durations (6, 12, 18, 24, 30 and 48 minutes) show statistically
significant positive (upward) trends whereas longer duration (subdaily
and daily) events generally show a statistically significant
negative (downward) trend. It is also found that the MK test and SR
test provide notably different results for some rainfall event durations
considered in this study. Since shorter duration sub-hourly rainfall
events show positive trends at many stations, the design rainfall data
based on stationary frequency analysis for these durations need to be
adjusted to account for the impact of climate change. These shorter
durations are more relevant to many urban development projects
based on smaller catchments having a much shorter response time.
Abstract: Aluminium and its alloys have excellent corrosion
resistant properties, ease of fabrication and high specific strength to
weight ratio. In this investigation an attempt has been made to study
the effect of different post weld heat treatment methods on the
mechanical and metallurgical properties of TIG welded joints of the
commercial aluminium alloy. Three different methods of post weld
heat treatments are solution heat treatment, artificial ageing and
combination of solution heat treatment and artificial aging are given
to TIG welded aluminium joints. Mechanical and metallurgical
properties of As welded joints of the aluminium alloys and post weld
heat treated joints of the aluminium alloys were examined.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: Esterification of p-bromo-m-cresol led to formation of
2-(4-bromo-3-methylphenoxy)acetate (1). 2-(4-Bromo-3-methyl
phenoxy)acetohydrazide (2) is derived from Compound (1) by
hydrazination. Compound (2) was reacted with different aromatic
aldehydes to yield N-(substituted benzylidiene)-2-(4-bromo-3-methyl
phenoxy)acetamide(3a-c). Cyclization of compound (3a-c) with
thioglycolic acid yielded 2-(4-bromo-3-methylphenoxy)-N-(4-oxo-2-
arylthiazolidin-3-yl) acetamide (4a-c). The newly synthesized
compounds were characterized on the basis of spectral studies and
evaluated for antibacterial and antifungal activities.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.