Abstract: The seismic risk mitigation from the perspective of
the old buildings stock is truly essential in Algerian urban areas,
particularly those located in seismic prone regions, such as Annaba
city, and which the old buildings present high levels of degradation
associated with no seismic strengthening and/or rehabilitation
concerns. In this sense, the present paper approaches the issue of the
seismic vulnerability assessment of old masonry building stocks
through the adaptation of a simplified methodology developed for a
European context area similar to that of Annaba city, Algeria.
Therefore, this method is used for the first level of seismic
vulnerability assessment of the masonry buildings stock of the old
city center of Annaba. This methodology is based on a vulnerability
index that is suitable for the evaluation of damage and for the
creation of large-scale loss scenarios. Over 380 buildings were
evaluated in accordance with the referred methodology and the
results obtained were then integrated into a Geographical Information
System (GIS) tool. Such results can be used by the Annaba city
council for supporting management decisions, based on a global view
of the site under analysis, which led to more accurate and faster
decisions for the risk mitigation strategies and rehabilitation plans.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: One of the key aspects of power quality improvement
in power system is the mitigation of voltage sags/swells and flicker.
Custom power devices have been known as the best tools for voltage
disturbances mitigation as well as reactive power compensation.
Dynamic Voltage Restorer (DVR) which is the most efficient and
effective modern custom power device can provide the most
commercial solution to solve several problems of power quality in
distribution networks. This paper deals with analysis and simulation
technique of DVR based on instantaneous power theory which is a
quick control to detect signals. The main purpose of this work is to
remove three important disturbances including voltage sags/swells
and flicker. Simulation of the proposed method was carried out on
two sample systems by using Matlab software environment and the
results of simulation show that the proposed method is able to
provide desirable power quality in the presence of wide range of
disturbances.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Mangosteen (Garcinia mangostana) pericarp is
considered as agricultural waste and not fully utilized in food
products. It is widely reported that mangosteen pericarp contains high
antioxidant properties. The objective of this study is to develop novel
yellow alkaline noodle (YAN) substituted with different levels of
mangosteen pericarp powder (MPP). YAN formulation was
substituted with different levels of MPP (0%, 5%, 10% and 15%).
The effect on nutritional and antioxidant properties was evaluated.
Higher substitution levels of MPP resulted in significant increase
(p
Abstract: In order to avoid self-collision of space manipulators
during operation process, a real-time detection method is proposed in
this paper. The manipulator is fitted into a cylinder-enveloping
surface, and then, a kind of detection algorithm of collision between
cylinders is analyzed. The collision model of space manipulator
self-links can be detected by using this algorithm in real-time detection
during the operation process. To ensure security of the operation, a
safety threshold is designed. The simulation and experiment results
verify the effectiveness of the proposed algorithm for a 7-DOF space
manipulator.
Abstract: Design concepts of real-time embedded system can be
realized initially by introducing novel design approaches. In this
literature, model based design approach and in-the-loop testing were
employed early in the conceptual and preliminary phase to formulate
design requirements and perform quick real-time verification. The
design and analysis methodology includes simulation analysis, model
based testing, and in-the-loop testing. The design of conceptual driveby-
wire, or DBW, algorithm for electronic control unit, or ECU, was
presented to demonstrate the conceptual design process, analysis, and
functionality evaluation. The concepts of DBW ECU function can be
implemented in the vehicle system to improve electric vehicle, or EV,
conversion drivability. However, within a new development process,
conceptual ECU functions and parameters are needed to be evaluated.
As a result, the testing system was employed to support conceptual
DBW ECU functions evaluation. For the current setup, the system
components were consisted of actual DBW ECU hardware, electric
vehicle models, and control area network or CAN protocol. The
vehicle models and CAN bus interface were both implemented as
real-time applications where ECU and CAN protocol functionality
were verified according to the design requirements. The proposed
system could potentially benefit in performing rapid real-time
analysis of design parameters for conceptual system or software
algorithm development.
Abstract: The aim of this research is to identify the key factors in shipping company’s port selection in order to providing their requirement. To identify and rank factors that play the main role in selecting port for providing the ship requirement, at the first step, data were collected via Semi-structured interviews, the aim was to generate knowledge on how shipping company select the port and suppliers for providing their needs. 37 port selection factors were chosen from the previous researches and field interviews and have been categorized into two groups of port's factor and the factors of services of suppliers companies. The current study adopts a questionnaire survey to the main shipping companies' operators in Iran. Their responses reveal that level of services of supplying companies and customs rules play the important role in selecting the ports. Our findings could affect decisions made by port authorities to consider that supporting the privet sections for ship chandelling business could have the best result in attracting ships.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: Corrosion of concrete sewer pipes induced by
sulphuric acid attack is a recognised problem worldwide, which is not
only an attribute of countries with hot climate conditions as thought
before. The significance of this problem is by far only realised when
the pipe collapses causing surface flooding and other severe
consequences. To change the existing post-reactive attitude of
managing companies, easy to use and robust models are required to
be developed which currently lack reliable data to be correctly
calibrated. This paper focuses on laboratory experiments of
establishing concrete pipe corrosion rate by submerging samples in to
0.5pH sulphuric acid solution for 56 days under 10ºC, 20ºC and 30ºC
temperature regimes. The result showed that at very early stage of the
corrosion process the samples gained overall mass, at 30ºC the
corrosion progressed quicker than for other temperature regimes,
however with time the corrosion level for 10ºC and 20ºC regimes
tended towards those at 30ºC. Overall, at these conditions the
corrosion rates of 10 mm/year, 13,5 mm/year and 17 mm/year were
observed.
Abstract: Rehabilitation of dam components such as foundations, buttresses, spillways and overtopping protection require a wide range of construction and design methodologies. Geotechnical Engineering considerations play an important role in the design and construction of foundations of new dams. Much investigation is required to assess and evaluate the existing dams. The application of roller compacting concrete (RCC) has been accepted as a new method for constructing new dams or rehabilitating old ones. In the past 40 years there have been so many changes in the usage of RCC and now it is one of most satisfactory solutions of water and hydropower resource throughout the world. The considerations of rehabilitation and construction of dams might differ due to upstream reservoir and its influence on penetrating and dewatering of downstream, operations requirements and plant layout. One of the advantages of RCC is its rapid placement which allows the dam to be operated quickly. Unlike ordinary concrete it is a drier mix, and stiffs enough for compacting by vibratory rollers. This paper evaluates some different aspects of RCC and focuses on its preparation progress.
Abstract: Testamentary succession rules in the Russian
Federation have been developing intensively since the collapse of the
Soviet Union. The article analyzes specific aspects of the closed will
in Russian civil law. It discusses advantages and drawbacks of the
closed will. In addition to that, the paper focuses on the will drafting
and attestation procedures. The research provides ways to improve
and enhance Russian legislation governing the closed will.
Abstract: Roadway planning and design is a very complex
process involving five key phases before a project is completed;
planning, project development, final design, right-of-way, and
construction. The planning phase for a new roadway transportation
project is a very critical phase as it greatly affects all latter phases of
the project. A location study is usually performed during the
preliminary planning phase in a new roadway project. The objective
of the location study is to develop alignment alternatives that are cost
efficient considering land acquisition and construction costs. This
paper describes a methodology to develop optimal preliminary
roadway alignments utilizing spatial-data. Four optimization criteria
are taken into consideration; roadway length, land cost, land slope,
and environmental impacts. The basic concept of the methodology is
to convert the proposed project area into a grid, which represents the
search space for an optimal alignment. The aforementioned
optimization criteria are represented in each of the grid’s cells. A
spatial-data optimization technique is utilized to find the optimal
alignment in the search space based on the four optimization criteria.
Two case studies for new roadway projects in Duval County in the
State of Florida are presented to illustrate the methodology. The
optimization output alignments are compared to the proposed Florida
Department of Transportation (FDOT) alignments. The comparison is
based on right-of-way costs for the alignments. For both case studies,
the right-of-way costs for the developed optimal alignments were
found to be significantly lower than the FDOT alignments.
Abstract: The structures obtained with the use of sandwich
technologies combine low weight with high energy absorbing
capacity and load carrying capacity. Hence, there is a growing and
markedly interest in the use of sandwiches with aluminum foam core
because of very good properties such as flexural rigidity and energy
absorption capability. In the current investigation, the static threepoint
bending tests were carried out on the sandwiches with
aluminum foam core and glass fiber reinforced polymer (GFRP)
skins at different values of support span distances aiming the analyses
of their flexural performance. The influence of the core thickness and
the GFRP skin type was reported in terms of peak load and energy
absorption capacity. For this purpose, the skins with two different
types of fabrics which have same thickness value and the aluminum
foam core with two different thicknesses were bonded with a
commercial polyurethane based flexible adhesive in order to combine
the composite sandwich panels. The main results of the bending tests
are: force-displacement curves, peak force values, absorbed energy,
collapse mechanisms and the effect of the support span length and
core thickness. The results of the experimental study showed that the
sandwich with the skins made of S-Glass Woven fabrics and with the
thicker foam core presented higher mechanical values such as load
carrying and energy absorption capacities. The increment of the
support span distance generated the decrease of the mechanical
values for each type of panels, as expected, because of the inverse
proportion between the force and span length. The most common
failure types of the sandwiches are debonding of the lower skin and
the core shear. The obtained results have particular importance for
applications that require lightweight structures with a high capacity
of energy dissipation, such as the transport industry (automotive,
aerospace, shipbuilding and marine industry), where the problems of
collision and crash have increased in the last years.
Abstract: A field study was conducted to evaluate the efficacy
of lavender for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. The
concentrations of Pb, Zn and Cd in lavender (roots, stems, leaves and
inflorescences) and in the essential oils of lavender were determined.
Lavender is a plant which is tolerant to heavy metals and can be
grown on contaminated soils, and which can be referred to the
hyperaccumulators of lead and the accumulators of cadmium and
zinc, and can be successfully used in the phytoremediation of heavy
metal contaminated soils. Favorable is also the fact that heavy metals
do not influence the development of the lavender, as well as on the
quality and quantity of the essential oil. The possibility of further
industrial processing will make lavender economically interesting
crops for farmers of phytoextraction technology.
Abstract: The article presents two mathematical models of the
interaction between a rotating shaft and an incompressible fluid. The
mathematical model includes both the journal bearings and the
axially traversed hydrodynamic sealing gaps of hydraulic machines.
A method is shown for the identification of additional effects of the
fluid acting on the rotor of the machine, both for a linear and a nonlinear
model. The interaction is expressed by matrices of mass,
stiffness and damping.
Abstract: The potential neuroprotective effect of Phyllantus
nuriri against Fe2+ and sodium nitroprusside (SNP) induced oxidative
stress in mitochondria of rats brain was evaluated. Cellular viability
was assessed by MTT reduction, reactive oxygen species (ROS)
generation was measured using the probe 2,7-dichlorofluoresce
indiacetate (DCFH-DA). Glutathione content was measured using
dithionitrobenzoic acid (DTNB). Fe2+ (10μM) and SNP (5μM)
significantly decreased mitochondrial activity, assessed by MTT
reduction assay, in a dose-dependent manner, this occurred in parallel
with increased glutathione oxidation, ROS production and lipid
peroxidation end-products (thiobarbituric acid reactive substances,
TBARS). The co-incubation with methanolic extract of Phyllantus
nuriri (10-200 μg/ml) reduced the disruption of mitochondrial
activity, gluthathione oxidation, ROS production as well as the
increase in TBARS levels caused by both Fe2+ and SNP in a dose
dependent manner. HPLC analysis of the extract revealed the
presence of gallic acid (20.540.01), caffeic acid (7.930.02), rutin
(25.310.05), quercetin (31.280.03) and kaemferol (14.360.01).
This result suggests that these phytochemicals account for the
protective actions of P. niruri against Fe2+ and SNP -induced
oxidative stress. Our results show that P. nuriri consist important
bioactive molecules in the search for an improved therapy against the
deleterious effects of Fe2+, an intrinsic producer of reactive oxygen
species (ROS), that leads to neuronal oxidative stress and
neurodegeneration.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: One of the main challenges in using the Discrete
Element Method (DEM) is to specify the correct input parameter
values. In general, the models are sensitive to the input parameter
values and accurate results can only be achieved if the correct values
are specified. For the linear contact model, micro-parameters such as
the particle density, stiffness, coefficient of friction, as well as the
particle size and shape distributions are required. There is a need for
a procedure to accurately calibrate these parameters before any
attempt can be made to accurately model a complete bulk materials
handling system. Since DEM is often used to model applications in
the mining and quarrying industries, a calibration procedure was
developed for materials that consist of relatively large (up to 40 mm
in size) particles. A coarse crushed aggregate was used as the test
material. Using a specially designed large shear box with a diameter
of 590 mm, the confined Young’s modulus (bulk stiffness) and
internal friction angle of the material were measured by means of the
confined compression test and the direct shear test respectively. DEM
models of the experimental setup were developed and the input
parameter values were varied iteratively until a close correlation
between the experimental and numerical results was achieved. The
calibration process was validated by modelling the pull-out of an
anchor from a bed of material. The model results compared well with
experimental measurement.
Abstract: Icons, or pictorial and graphical objects, are
commonly used in human-computer interaction (HCI) fields as the
mediator in order to communicate information to users. Yet there has
been little studies focusing on a majority of the world’s population –
semi-literate communities – in terms of the fundamental knowhow
for designing icons for such population. In this study, two sets of
icons belonging in different icon taxonomy – abstract and concrete –
are designed for a mobile application for semi-literate agricultural
communities. In this paper, we propose a triadic relationship of an
icon, namely meaning, task and mental image, which inherits the
triadic relationship of a sign. User testing with the application and a
post-pilot questionnaire are conducted as the experimental approach
in two rural villages in India. Icons belonging to concrete taxonomy
perform better than abstract icons on the premise that the design of
the icon fulfills the underlying rules of the proposed triadic
relationship.