Abstract: This paper present the experimental work of double
unit tunnel form building (TFB) subjected to in-plane lateral cyclic
loading. A one third scale of 3-storey double unit of TFB is tested
until its strength degradation. Then, the TFB is repaired and
retrofitted using additional shear wall, steel angle and CFRP sheet.
The crack patterns, lateral strength, stiffness, ductility and equivalent
viscous damping (EVD) were analyzed and compared before and
after repair and retrofit. The result indicates that the lateral strength
increases by 22% in pushing and 27% in pulling direction. Moreover,
the stiffness and ductility obtained before and after retrofit increase
tremendously by 87.87% and 39.66%, respectively. Meanwhile, the
energy absorption measured by equivalent viscous damping obtained
after retrofit increase by 12.34% in pulling direction. It can be
concluded that the proposed retrofit method is capable to increase the
lateral strength capacity, stiffness and energy absorption of double
unit TFB.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: One of the biggest challenges facing Theological/
Religious Education in Nigeria is access to quality learning materials.
For instance at the Trinity (Union) Theological College, Umuahia, it
was difficult for lecturers to access suitable and qualitative materials
for instruction especially the ones that would suit the African context
and stimulate a deep rooted interest among the students. Some
textbooks written by foreign authors were readily available in the
School Library, but were lacking in the College bookshops for
students to own copies. Even when the College was able to order
some of the books from abroad, it did not usher in the needed
enthusiasm expected from the students because they were either very
expensive or very difficult to understand during private studies. So it
became necessary to develop contextual materials which were
affordable and understandable, though with little success. The
National Open University of Nigeria (NOUN)’s innovation in the
development and sharing of learning resources through its Open
Courseware is a welcome development and of great assistance to
students. Apart from NOUN students who could easily access the
materials, many others from various theological/religious institutes
across the nation have benefited immensely. So, the thesis of this
paper is that the promotion of open educational resources in
theological/religious education in Nigeria would facilitate a better
informed/equipped religious leadership, which would in turn impact
its adherents for a healthier society and national development.
Adopting a narrative and historical approach within the context of
Nigeria’s educational system, the paper discusses: educational
traditions in Nigeria; challenges facing theological/religious
education in Nigeria; and benefits of open educational resources. The
study goes further to making recommendations on how OER could
positively influence theological/religious education in Nigeria. It is
expected that theologians, religious educators, and ODL practitioners
would find this work very useful.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Esterification of p-bromo-m-cresol led to formation of
2-(4-bromo-3-methylphenoxy)acetate (1). 2-(4-Bromo-3-methyl
phenoxy)acetohydrazide (2) is derived from Compound (1) by
hydrazination. Compound (2) was reacted with different aromatic
aldehydes to yield N-(substituted benzylidiene)-2-(4-bromo-3-methyl
phenoxy)acetamide(3a-c). Cyclization of compound (3a-c) with
thioglycolic acid yielded 2-(4-bromo-3-methylphenoxy)-N-(4-oxo-2-
arylthiazolidin-3-yl) acetamide (4a-c). The newly synthesized
compounds were characterized on the basis of spectral studies and
evaluated for antibacterial and antifungal activities.
Abstract: Due to the large amount of information in the World
Wide Web (WWW, web) and the lengthy and usually linearly
ordered result lists of web search engines that do not indicate
semantic relationships between their entries, the search for topically
similar and related documents can become a tedious task. Especially,
the process of formulating queries with proper terms representing
specific information needs requires much effort from the user. This
problem gets even bigger when the user's knowledge on a subject and
its technical terms is not sufficient enough to do so. This article
presents the new and interactive search application DocAnalyser that
addresses this problem by enabling users to find similar and related
web documents based on automatic query formulation and state-ofthe-
art search word extraction. Additionally, this tool can be used to
track topics across semantically connected web documents.
Abstract: In this paper, we have proposed a parallel IDS and
honeypot based approach to detect and analyze the unknown and
known attack taxonomy for improving the IDS performance and
protecting the network from intruders. The main theme of our
approach is to record and analyze the intruder activities by using both
the low and high interaction honeypots. Our architecture aims to
achieve the required goals by combing signature based IDS,
honeypots and generate the new signatures. The paper describes the
basic component, design and implementation of this approach and
also demonstrates the effectiveness of this approach to reduce the
probability of network attacks.
Abstract: Apps are today the most important possibility to adapt
mobile phones and computers to fulfill the special needs of their
users. Location- and context-sensitive programs are hereby the key to
support the interaction of the user with his/her environment and also
to avoid an overload with a plenty of dispensable information. The
contribution shows, how a trusted, secure and really bi-directional
communication and interaction among users and their environment
can be established and used, e.g. in the field of home automation.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: Nations are still finding it quite difficult to win mega
sport competitions despite the major contribution of sport to society
in terms of social and economic development, personal health, and in
education. Even though the world of sports has been transformed into
a huge global economy, it is important to note that the first step of
sport is usually its introduction to children at school through physical
education or PE. In other words, nations who do not win mega sport
competitions also suffer from a weak and neglected PE system. This
problem of the neglect of PE systems is the main motivation of this
research aimed at examining the factors affecting the perceived
awareness of physical education teachers on the ICTs that are
adoptable for the teaching and learning of physical education. Two
types of research objectives will materialize this aim: relevant
theories will be identified in relation to the analysis of the perceived
ICT awareness of PE teachers and subsequent models will be
compiled and designed from existing literature; the empirical testing
of such theories and models will also be achieved through the survey
of PE teachers from the Camperdown magisterial district of the
KwaZulu-Natal province of South Africa. The main hypothesis at the
heart of this study is the relationship between the demographics of PE
teachers, their behavior both as individuals and as social entities, and
their perceived awareness of the ICTs that are adoptable for PE, as
postulated by existing literature; except that this study categorizes
human behavior under performance expectancy, computer attitude,
and social influence. This hypothesis was partially confirmed by the
survey conducted by this research in the sense that performance
expectancy and teachers’ age, gender, computer usage, and class size
were found to be the only factors affecting their awareness of ICTs
for physical education.
Abstract: The world wide web network is a network with a
complex topology, the main properties of which are the distribution
of degrees in power law, A low clustering coefficient and a weak
average distance. Modeling the web as a graph allows locating the
information in little time and consequently offering a help in the
construction of the research engine. Here, we present a model based
on the already existing probabilistic graphs with all the aforesaid
characteristics. This work will consist in studying the web in order to
know its structuring thus it will enable us to modelize it more easily
and propose a possible algorithm for its exploration.
Abstract: In order to study the effect of drought stress on grain
yield, yield components and associated traits of durum wheat
cultivars, an experiment was done as split plot arrangement using
randomized complete block design with three replications in Ilam
province, Iran in 2009-2010 cropping season. Different levels of
irrigation (Full irrigation, drought stress at stem elongation,
Flowering and grain formation stages) were considered as a main plot
and three durum wheat cultivars (Yavaros, Seimareh and Karkheh)
were assigned as a sub plot. The results showed that drought stress
was significant on grain yield, spike.m-2, grain. Spike-1, 1000-grain
weight, biological yield, harvest index and protein content. Drought
stress at all stages caused a loss in grain yield and its components.
Full irrigation had the highest grain yield and yield components.
Drought stress at stem elongation, flowering and grain formation
stages caused a reduction in spike.m-2, grain.spike-1 and 1000-grain
weight, respectively. Protein content was significantly affected by
drought stress. The highest protein content was obtained from
drought stress at grain formation stage. Cultivars had an influence on
grain yield and yield components. Yavaros and Seimareh cultivars
had the highest and lowest grain yield, respectively. Interaction effect
between drought stress and cultivar had a significant effect on grain
and yield components. Full irrigation and Yavaros cultivar had the
highest grain yield and drought stress at grain formation stage and
Seimareh cultivar had the lowest grain yield, respectively.
Abstract: The development of the agricultural sector in Ghana
has been reliant on the use of irrigation systems to ensure food
security. However, the manual operation of these systems has not
facilitated their maximum efficiency due to human limitations.
This paper seeks to address this problem by designing and
implementing an efficient, cost effective automated system which
monitors and controls the water flow of irrigation through
communication with an authorized operator via text messages. The
automatic control component of the system is timer based with an
Atmega32 microcontroller and a real time clock from the SM5100B
cellular module. For monitoring purposes, the system sends periodic
notification of the system on the performance of duty via SMS to the
authorized person(s). Moreover, the GSM based Irrigation
Monitoring and Control System saves time and labour and reduces
cost of operating irrigation systems by saving electricity usage and
conserving water.
Field tests conducted have proven its operational efficiency and
ease of assessment of farm irrigation equipment due to its costeffectiveness
and data logging capabilities.
Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: In this paper a scheme is proposed for generating
a programmable current reference which can be implemented
in the CMOS technology. The current can be varied over a
wide range by changing an external voltage applied to one
of the control gates of FGMOS (Floating Gate MOSFET).
For a range of supply voltages and temperature, CMOS
current reference is found to be dependent, this dependence
is compensated by subtracting two current outputs with the
same dependencies on the supply voltage and temperature.
The system performance is found to improve with the
use of FGMOS. Mathematical analysis of the proposed
circuit is done to establish supply voltage and temperature
independence. Simulation and performance evaluation of the
proposed current reference circuit is done using TANNER
EDA Tools. The current reference shows the supply and
temperature dependencies of 520 ppm/V and 312 ppm/oC,
respectively. The proposed current reference can operate down
to 0.9 V supply.
Abstract: In this paper, numerical solution of system of
Fredholm and Volterra integral equations by means of the Spline
collocation method is considered. This approximation reduces the
system of integral equations to an explicit system of algebraic
equations. The solution is collocated by cubic B-spline and the
integrand is approximated by the Newton-Cotes formula. The error
analysis of proposed numerical method is studied theoretically. The
results are compared with the results obtained by other methods to
illustrate the accuracy and the implementation of our method.
Abstract: The main goal of this paper was evaluate the effect of
diets containing different levels of probiotic on performance and milk
composition of lactating cows.
Eight Holstein cows were distributed in two 4x4 Latin square. The
diets were based on corn silage, concentrate and the treatment (0, 3, 6
or 9 grams of probiotic/animal/day). It was evaluated the dry matter
intake of nutrients, milk yield and composition.
The use of probiotics did not affect the nutrient intake (p>0.05)
neither the daily milk production or corrected to 4% fat (p>0.05).
However, it was observed that there was a significant fall in milk
composition with higher levels of probiotics supplementation.
These results emphasize the need of further studies with different
experimental designs or improve the number of Latin square with
longer periods of adaptation.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.