Abstract: The MFCAV Riemann solver is practically used in many Lagrangian or ALE methods due to its merit of sharp shock profiles and rarefaction corners, though very often with numerical oscillations. By viewing it as a modification of the WWAM Riemann solver, we apply the MFCAV Riemann solver to the Lagrangian method recently developed by Maire. P. H et. al.. The numerical experiments show that the application is successful in that the shock profiles and rarefaction corners are sharpened compared with results obtained using other Riemann solvers. Though there are still numerical oscillations, they are within the range of the MFCAV applied in onther Lagrangian methods.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: Method of determining of moisture diffusivity on two types of autoclaved aerated concretes with different bulk density is represented in the paper. On the specimens were measured one dimensional water transport only on liquid phase. Ever evaluation was done from moisture profiles measured in specific times by capacitance moisture meter. All values from capacitance meter were recalculated to moisture content by mass. Moisture diffusivity was determined in dependence on both moisture and temperature. The experiment temperatures were set at values 55, 65, 75 and 85°C.
Abstract: Enterprise applications are complex systems that are hard to develop and deploy in organizations. Although software application development tools, frameworks, methodologies and patterns are rapidly developing; many projects fail by causing big costs. There are challenging issues that programmers and designers face with while working on enterprise applications. In this paper, we present the three of the significant issues: Architectural, technological and performance. The important subjects in each issue are pointed out and recommendations are given. In architectural issues the lifecycle, meta-architecture, guidelines are pointed out. .NET and Java EE platforms are presented in technological issues. The importance of performance, measuring performance and profilers are explained in performance issues.
Abstract: Rainbow trout homogametic males, (XX or YY sex genotype), can be obtained, respectively, through masculinisation of genetic females or induced androgenesis. Aim of this study was to compare reproductive potential of neo-males (XX) and super-males (YY) with heterogametic males (XY). We measured spermatozoa motility parameters, sperm concentration, osmolality and characterized protein profiles in samples of stripped and testicular sperm obtained from XY and YY males, and testicular sperm of XX males. The motile spermatozoa, as measured by both subjective method and CASA, showed no differences between testicular sperm of XX males and stripped sperm of XY and YY males whereas testicular sperm of XY and YY males had significantly lower sperm motility. Result of protein densitometry showed similarities in protein profile between seminal plasma of XY and YY males and testicular fluids of XX males. Testis of XX males showed specific histological structures of cysts consists hypertrophied Sertoli cells.
Abstract: A model of user behaviour based automated planning
is introduced in this work. The behaviour of users of web interactive
systems can be described in term of a planning domain encapsulating
the timed actions patterns representing the intended user profile. The
user behaviour recognition is then posed as a planning problem
where the goal is to parse a given sequence of user logs of the
observed activities while reaching a final state.
A general technique for transforming a timed finite state automata
description of the behaviour into a numerical parameter planning
model is introduced.
Experimental results show that the performance of a planning
based behaviour model is effective and scalable for real world
applications. A major advantage of the planning based approach is to
represent in a single automated reasoning framework problems of
plan recognitions, plan synthesis and plan optimisation.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: Using Dynamic Bayesian Networks (DBN) to model genetic regulatory networks from gene expression data is one of the major paradigms for inferring the interactions among genes. Averaging a collection of models for predicting network is desired, rather than relying on a single high scoring model. In this paper, two kinds of model searching approaches are compared, which are Greedy hill-climbing Search with Restarts (GSR) and Markov Chain Monte Carlo (MCMC) methods. The GSR is preferred in many papers, but there is no such comparison study about which one is better for DBN models. Different types of experiments have been carried out to try to give a benchmark test to these approaches. Our experimental results demonstrated that on average the MCMC methods outperform the GSR in accuracy of predicted network, and having the comparable performance in time efficiency. By proposing the different variations of MCMC and employing simulated annealing strategy, the MCMC methods become more efficient and stable. Apart from comparisons between these approaches, another objective of this study is to investigate the feasibility of using DBN modeling approaches for inferring gene networks from few snapshots of high dimensional gene profiles. Through synthetic data experiments as well as systematic data experiments, the experimental results revealed how the performances of these approaches can be influenced as the target gene network varies in the network size, data size, as well as system complexity.
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: The present microfluidic study is emphasizing the flow behavior within a Y shape micro-bifurcation in two similar flow configurations. We report here a numerical and experimental investigation on the velocity profiles evolution and secondary flows, manifested at different Reynolds numbers (Re) and for two different boundary conditions. The experiments are performed using special designed setup based on optical microscopic devices. With this setup, direct visualizations and quantitative measurements of the path-lines are obtained. A Micro-PIV measurement system is used to obtain velocity profiles distributions in a spatial evolution in the main flows domains. The experimental data is compared with numerical simulations performed with commercial computational code FLUENT in a 3D geometry with the same dimensions as the experimental one. The numerical flow patterns are found to be in good agreement with the experimental manifestations.
Abstract: Microarray data profiles gene expression on a whole
genome scale, therefore, it provides a good way to study associations
between gene expression and occurrence or progression of cancer.
More and more researchers realized that microarray data is helpful
to predict cancer sample. However, the high dimension of gene
expressions is much larger than the sample size, which makes this
task very difficult. Therefore, how to identify the significant genes
causing cancer becomes emergency and also a hot and hard research
topic. Many feature selection algorithms have been proposed in
the past focusing on improving cancer predictive accuracy at the
expense of ignoring the correlations between the features. In this
work, a novel framework (named by SGS) is presented for stable gene
selection and efficient cancer prediction . The proposed framework
first performs clustering algorithm to find the gene groups where
genes in each group have higher correlation coefficient, and then
selects the significant genes in each group with Bayesian Lasso and
important gene groups with group Lasso, and finally builds prediction
model based on the shrinkage gene space with efficient classification
algorithm (such as, SVM, 1NN, Regression and etc.). Experiment
results on real world data show that the proposed framework often
outperforms the existing feature selection and prediction methods,
say SAM, IG and Lasso-type prediction model.
Abstract: This paper reports our analysis of 163 ks observations
of PSR J0538+2817 with the Rossi X-Ray Timing Explorer
(RXTE).The pulse profiles, detected up to 60 keV, show a single
peak asin the case for radio frequency. The profile is well described
by one Gaussians function with full width at half maximum (FWHM)
0.04794. We compared the difference of arrival time between radio
and X-ray pulse profiles for the first time. It turns out that the phase
of radio emits precede the X-ray by 8.7 ± 4.5 ms. Furthermore we
obtained the pulse profiles in the energy ranges of 2.29-6.18 keV,
6.18-12.63 keV and 12.63-17.36 keV. The intensity of pulses
decreases with the increasing energy range. We discuss the emission
geometry in our work.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: To minimize power losses, it is important to
determine the location and size of local generators to be placed in
unbalanced power distribution systems. On account of some inherent
features of unbalanced distribution systems, such as radial structure,
large number of nodes, a wide range of X/R ratios, the conventional
techniques developed for the transmission systems generally fail on
the determination of optimum size and location of distributed
generators (DGs). This paper presents a simple method for
investigating the problem of contemporaneously choosing best
location and size of DG in three-phase unbalanced radial distribution
system (URDS) for power loss minimization and to improve the
voltage profile of the system. Best location of the DG is determined
by using voltage index analysis and size of DG is computed by
variational technique algorithm according to available standard size
of DGs. This paper presents the results of simulations for 25-bus and
IEEE 37- bus Unbalanced Radial Distribution system.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: The flow and heat transfer mechanism in convex
corrugated tubes have been investigated through numerical
simulations in this paper. Two kinds of tube types named as symmetric
corrugated tube (SCT) and asymmetric corrugated tube (ACT) are
modeled and studied numerically based on the RST model. The
predictive capability of RST model is examined in the corrugation wall
in order to check the reliability of RST model under the corrugation
wall condition. We propose a comparison between the RST modelling
the corrugation wall with existing direct numerical simulation of Maaß
C and Schumann U [14]. The numerical results pressure coefficient at
different profiles between RST and DNS are well matched. The
influences of large corrugation tough radii to heat transfer and flow
characteristic had been considered. Flow and heat transfer comparison
between SCT and ACT had been discussed. The numerical results
show that ACT exhibits higher overall heat transfer performance than
SCT.