Abstract: Ventilation is a fundamental requirement for
occupant health and indoor air quality in buildings. Natural
ventilation can be used as a design strategy in free-running
buildings to:
• Renew indoor air with fresh outside air and lower room
temperatures at times when the outdoor air is cooler.
• Promote air flow to cool down the building structure
(structural cooling).
• Promote occupant physiological cooling processes
(comfort cooling).
This paper focuses on ways in which ventilation can
provide the mechanism for heat dissipation and cooling of the
building structure..It also discusses use of ventilation as a
means of increasing air movement to improve comfort when
indoor air temperatures are too high. The main influencing
factors and design considerations and quantitative guidelines
to help meet the design objectives are also discussed.
Abstract: This paper develops an unscented grid-based filter
and a smoother for accurate nonlinear modeling and analysis
of time series. The filter uses unscented deterministic sampling
during both the time and measurement updating phases, to approximate
directly the distributions of the latent state variable. A
complementary grid smoother is also made to enable computing
of the likelihood. This helps us to formulate an expectation
maximisation algorithm for maximum likelihood estimation of
the state noise and the observation noise. Empirical investigations
show that the proposed unscented grid filter/smoother compares
favourably to other similar filters on nonlinear estimation tasks.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.
Abstract: The localized corrosion behavior of laser surface
melted 304L austenitic stainless steel was studied by
potentiodynamic polarization test. The extent of improvement in
corrosion resistance was governed by the preferred orientation and
the percentage of delta ferrite present on the surface of the laser
melted sample. It was established by orientation imaging microscopy
that the highest pitting potential value was obtained when grains were
oriented in the most close- packed [101] direction compared to the
random distribution of the base metal and other laser surface melted
samples oriented in [001] direction. The sample with lower
percentage of ferrite had good pitting resistance.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: We propose a decoy-pulse protocol for frequency-coded implementation of B92 quantum key distribution protocol. A direct extension of decoy-pulse method to frequency-coding scheme results in security loss as an eavesdropper can distinguish between signal and decoy pulses by measuring the carrier photon number without affecting other statistics. We overcome this problem by optimizing the ratio of carrier photon number of decoy-to-signal pulse to be as close to unity as possible. In our method the switching between signal and decoy pulses is achieved by changing the amplitude of RF signal as opposed to modulating the intensity of optical signal thus reducing system cost. We find an improvement by a factor of 100 approximately in the key generation rate using decoy-state protocol. We also study the effect of source fluctuation on key rate. Our simulation results show a key generation rate of 1.5×10-4/pulse for link lengths up to 70km. Finally, we discuss the optimum value of average photon number of signal pulse for a given key rate while also optimizing the carrier ratio.
Abstract: As the Computed Tomography(CT) requires normally
hundreds of projections to reconstruct the image, patients are exposed
to more X-ray energy, which may cause side effects such as cancer.
Even when the variability of the particles in the object is very less,
Computed Tomography requires many projections for good quality
reconstruction. In this paper, less variability of the particles in an
object has been exploited to obtain good quality reconstruction.
Though the reconstructed image and the original image have same
projections, in general, they need not be the same. In addition
to projections, if a priori information about the image is known,
it is possible to obtain good quality reconstructed image. In this
paper, it has been shown by experimental results why conventional
algorithms fail to reconstruct from a few projections, and an efficient
polynomial time algorithm has been given to reconstruct a bi-level
image from its projections along row and column, and a known sub
image of unknown image with smoothness constraints by reducing the
reconstruction problem to integral max flow problem. This paper also
discusses the necessary and sufficient conditions for uniqueness and
extension of 2D-bi-level image reconstruction to 3D-bi-level image
reconstruction.
Abstract: Wireless Mesh Networking is a promising proposal
for broadband data transmission in a large area with low cost and
acceptable QoS. These features- trade offs in WMNs is a hot research
field nowadays. In this paper a mathematical optimization framework
has been developed to maximize throughput according to upper
bound delay constraints. IEEE 802.11 based infrastructure
backhauling mode of WMNs has been considered to formulate the
MINLP optimization problem. Proposed method gives the full
routing and scheduling procedure in WMN in order to obtain
mentioned goals.
Abstract: A great deal of research works in the field information
systems security has been based on a positivist paradigm. Applying
the reductionism concept of the positivist paradigm for information
security means missing the bigger picture and thus, the lack of holism
which could be one of the reasons why security is still overlooked,
comes as an afterthought or perceived from a purely technical
dimension. We need to reshape our thinking and attitudes towards
security especially in a complex and dynamic environment such as e-
Business to develop a holistic understanding of e-Business security in
relation to its context as well as considering all the stakeholders in
the problem area. In this paper we argue the suitability and need for
more inductive interpretive approach and qualitative research method
to investigate e-Business security. Our discussion is based on a
holistic framework of enquiry, nature of the research problem, the
underling theoretical lens and the complexity of e-Business
environment. At the end we present a research strategy for
developing a holistic framework for understanding of e-Business
security problems in the context of developing countries based on an
interdisciplinary inquiry which considers their needs and
requirements.
Abstract: The objective of this research is parameters optimized
of the stair shape workpiece which is cut by CNC Wire-Cut EDM
(WEDW). The experiment material is SKD-11 steel of stair-shaped
with variable height workpiece 10, 20, 30 and 40 mm. with the same
10 mm. thickness are cut by Sodick's CNC Wire-Cut EDM model
AD325L.
The experiments are designed by 3k full factorial experimental
design at 3 level 2 factors and 9 experiments with 2 replicate. The
selected two factor are servo voltage (SV) and servo feed rate (SF)
and the response is cutting thickness error. The experiment is divided
in two experiments. The first experiment determines the significant
effective factor at confidential interval 95%. The SV factor is the
significant effective factor from first result. In order to result smallest
cutting thickness error of workpieces is 17 micron with the SV value
is 46 volt. Also show that the lower SV value, the smaller different
thickness error of workpiece. Then the second experiment is done to
reduce different cutting thickness error of workpiece as small as
possible by lower SV. The second experiment result show the
significant effective factor at confidential interval 95% is the SV
factor and the smallest cutting thickness error of workpieces reduce
to 11 micron with the experiment SV value is 36 volt.
Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: The great majority of the electric installations belong
to the first and second category. In order to ensure a high level of
reliability of their electric system feeder, two power supply sources
are envisaged, one principal, the other of reserve, generally a cold
reserve (electric diesel group).
The principal source being under operation, its control can be ideal
and sure, however for the reserve source being in stop, a preventive
maintenance-s which proceeds on time intervals (periodicity) and
for well defined lengths of time are envisaged, so that this source will
always available in case of the principal source failure.
The choice of the periodicity of preventive maintenance of the
source of reserve influences directly the reliability of the electric
feeder system. On the basis of the semi-markovians processes, the
influence of the periodicity of the preventive maintenance of the
source of reserve is studied and is given the optimal periodicity.
Abstract: In this work, we present for the first time in our
perception an efficient digital watermarking scheme for mpeg audio
layer 3 files that operates directly in the compressed data domain,
while manipulating the time and subband/channel domain. In
addition, it does not need the original signal to detect the watermark.
Our scheme was implemented taking special care for the efficient
usage of the two limited resources of computer systems: time and
space. It offers to the industrial user the capability of watermark
embedding and detection in time immediately comparable to the real
music time of the original audio file that depends on the mpeg
compression, while the end user/audience does not face any artifacts
or delays hearing the watermarked audio file. Furthermore, it
overcomes the disadvantage of algorithms operating in the PCMData
domain to be vulnerable to compression/recompression attacks,
as it places the watermark in the scale factors domain and not in the
digitized sound audio data. The strength of our scheme, that allows it
to be used with success in both authentication and copyright
protection, relies on the fact that it gives to the users the enhanced
capability their ownership of the audio file not to be accomplished
simply by detecting the bit pattern that comprises the watermark
itself, but by showing that the legal owner knows a hard to compute
property of the watermark.
Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.
Abstract: In this paper, we propose an advanced ILQ control for the buck-converter via two-degrees of freedom servo-system. Our presented strategy is based on Inverse Linear Quadratic (ILQ) servo-system controller without solving Riccati-s equation directly. The optimal controller of the current and voltage control system is designed. The stability and robust control are analyzed. A conscious and persistent effort has been made to improve ILQ control via two-degrees of freedom guarantees the optimal gains on the basis of polynomial pole assignment, which our results of the proposed strategy shows that the advanced ILQ control can be controlled independently the step response and the disturbance response by appending a feed-forward compensator.
Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.