Abstract: Control of a semi-batch polymerization reactor using
an adaptive radial basis function (RBF) neural network method is
investigated in this paper. A neural network inverse model is used to
estimate the valve position of the reactor; this method can identify the
controlled system with the RBF neural network identifier. The
weights of the adaptive PID controller are timely adjusted based on
the identification of the plant and self-learning capability of RBFNN.
A PID controller is used in the feedback control to regulate the actual
temperature by compensating the neural network inverse model
output. Simulation results show that the proposed control has strong
adaptability, robustness and satisfactory control performance and the
nonlinear system is achieved.
Abstract: This paper deals with advanced state estimation algorithms for estimation of biomass concentration and specific growth rate in a typical fed-batch biotechnological process. This biotechnological process was represented by a nonlinear mass-balance based process model. Extended Kalman Filter (EKF) and Particle Filter (PF) was used to estimate the unmeasured state variables from oxygen uptake rate (OUR) and base consumption (BC) measurements. To obtain more general results, a simplified process model was involved in EKF and PF estimation algorithms. This model doesn’t require any special growth kinetic equations and could be applied for state estimation in various bioprocesses. The focus of this investigation was concentrated on the comparison of the estimation quality of the EKF and PF estimators by applying different measurement noises. The simulation results show that Particle Filter algorithm requires significantly more computation time for state estimation but gives lower estimation errors both for biomass concentration and specific growth rate. Also the tuning procedure for Particle Filter is simpler than for EKF. Consequently, Particle Filter should be preferred in real applications, especially for monitoring of industrial bioprocesses where the simplified implementation procedures are always desirable.
Abstract: A continuous time model of the interaction between
crop insect pests and naturally beneficial pest enemies is created
using a set of simultaneous, non-linear, ordinary differential
equations incorporating natural death rates based on the Weibull
distribution. The crop pest is present in all its life-cycle stages of:
egg, larva, pupa and adult. The beneficial insects, parasitoid wasps,
may be present in either or all parasitized: eggs, larva and pupa.
Population modelling is used to estimate the quantity of the natural
pest enemies that should be introduced into the pest infested
environment to suppress the pest population density to an
economically acceptable level within a prescribed number of days.
The results obtained illustrate the effect of different combinations of
parasitoid wasps, using the Pascal distribution to estimate their
success in parasitizing different pest developmental stages, to deliver
pest control to a sustainable level. Effective control, within a
prescribed number of days, is established by the deployment of two
or all three species of wasps, which partially destroy pest: egg, larvae
and pupae stages. The selected scenarios demonstrate effective
sustainable control of the pest in less than thirty days.
Abstract: Chaotic analysis has been performed on the river flow time series before and after applying the wavelet based de-noising techniques in order to investigate the noise content effects on chaotic nature of flow series. In this study, 38 years of monthly runoff data of three gauging stations were used. Gauging stations were located in Ghar-e-Aghaj river basin, Fars province, Iran. Noise level of time series was estimated with the aid of Gaussian kernel algorithm. This step was found to be crucial in preventing removal of the vital data such as memory, correlation and trend from the time series in addition to the noise during de-noising process.
Abstract: Photoacoustic imaging (PAI) is a non-invasive and
non-ionizing imaging modality that combines the absorption contrast
of light with ultrasound resolution. Laser is used to deposit optical
energy into a target (i.e., optical fluence). Consequently, the target
temperature rises, and then thermal expansion occurs that leads to
generating a PA signal. In general, most image reconstruction
algorithms for PAI assume uniform fluence within an imaging object.
However, it is known that optical fluence distribution within the
object is non-uniform. This could affect the reconstruction of PA
images. In this study, we have investigated the influence of optical
fluence distribution on PA back-propagation imaging using finite
element method. The uniform fluence was simulated as a triangular
waveform within the object of interest. The non-uniform fluence
distribution was estimated by solving light propagation within a
tissue model via Monte Carlo method. The results show that the PA
signal in the case of non-uniform fluence is wider than the uniform
case by 23%. The frequency spectrum of the PA signal due to the
non-uniform fluence has missed some high frequency components in
comparison to the uniform case. Consequently, the reconstructed
image with the non-uniform fluence exhibits a strong smoothing
effect.
Abstract: The effects of varying air temperature (full, ¾ full, ½ full aircon adjustment, no aircon) in polishing component of Single-Pass Mill on the quality of Philippine inbred rice variety, was investigated. Parameters measured were milling recovery (MR), headrice recovery (HR), and percentage with bran streaks. Cooling method (with aircon) increased MR, HR, and percentage with bran streaks of milled rice. Highest MR and HR (67.62%; 47.33%) were obtained from ¾ full adjustment whereas no aircon were lowest (66.27%; 39.76%). Temperature in polishing component at ¾ full adjustment was 33oC whereas no aircon was 45oC. There was increase of 1.35% in MR and 7.57% in HR. Additional cost of milling per kg due to aircon cooling was P0.04 at 300 tons/yr volume, with 0.15 yr payback period. Net income was estimated at ₱98,100.00. Percentage of kernels with bran streaks increased from 5%–14%, indicating more nutrients of milled rice.
Abstract: The sound pressure level (SPL) of the moving-coil
loudspeaker (MCL) is often simulated and analyzed using the lumped
parameter model. However, the SPL of a MCL cannot be simulated
precisely in the high frequency region, because the value of cone
effective area is changed due to the geometry variation in different
mode shapes, it is also related to affect the acoustic radiation mass and
resistance. Herein, the paper presents the inverse method which has a
high ability to measure the value of cone effective area in various
frequency points, also can estimate the MCL electroacoustic
parameters simultaneously. The proposed inverse method comprises
the direct problem, adjoint problem, and sensitivity problem in
collaboration with nonlinear conjugate gradient method. Estimated
values from the inverse method are validated experimentally which
compared with the measured SPL curve result. Results presented in
this paper not only improve the accuracy of lumped parameter model
but also provide the valuable information on loudspeaker cone design.
Abstract: A novel new vanadium (IV) complexes incorporating the chelating diamido cyclopentadienyl {ArN(CH2)3NAr)}2-((ηn-Cp)Cp)} (Ar = 2,6-Pri2C6H3)(Cp = C5H5 and n = 1,2,3,4 and 5) have been studied with calculation of the properties of species involved in various of cyclopentadienyl reaction. These were carried out under investigation of density functional theory (DFT) calculation, and comparing together. Other methods, explicitly including electron correlation, are necessary for more accurate calculations; MB3LYP (Becke) (Lee–Yang–Parr) level of theory often being used to obtain more exact results. These complexes were estimated of electronic energy for molecular system, because it accounts for all electron correlation interactions.
The optimised of [V(ArN(CH2)3NAr)2Cl(η5-Cp)] (Ar = 2,6-Pri2C6H3 and Cp= C5H5) was found to be thermally more stable than others of vanadium cyclopentadienyl. In the meantime the complex [V(ArN(CH2)3NAr)2Cl(η1-Cp)] (Ar = 2,6-Pri2C6H3 and Cp= C5H5) which is showed a low thermal stability in case of the just one carbon of cyclopentadienyl can be insertion with vanadium metal centre. By using Dewar-Chatt-Duncanson model, as a basis of the molecular orbital (MO) analysis and showed the highest occupied molecular orbital (HOMO) and lowest occupied molecular orbital LUMO.
Abstract: This investigation develops a revisable method for estimating the estimate value of equivalent 10 Hz voltage flicker (DV10) of a DC Electric Arc Furnace (EAF). This study also discusses three 161kV DC EAFs by field measurement, with those results indicating that the estimated DV10 value is significantly smaller than the survey value. The key point is that the conventional means of estimating DV10 is inappropriate. There is a main cause as the assumed Qmax is too small.
Although DC EAF is regularly operated in a constant MVA mode, the reactive power variation in the Main Transformer (MT) is more significant than that in the Furnace Transformer (FT). A substantial difference exists between estimated maximum reactive power fluctuation (DQmax) and the survey value from actual DC EAF operations. However, this study proposes a revisable method that can obtain a more accurate DV10 estimate than the conventional method.
Abstract: The scope of this paper is to evaluate and compare the potential of LS-PV(Large Scale Photovoltaic Power Plant) power generation systems in the southern region of Libya at Al-Kufra for both stationary and tracking systems. A Microsoft Excel-VBA program has been developed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency of the system for stationary system and for tracking system. The results for energy production show that the total energy output is 114GWh/year for stationary system and 148GWh/year for tracking system. The average module efficiency for the stationary system is 16.6% and 16.2% for the tracking system.
The values of electricity generation capacity factor (CF) and solar capacity factor (SCF) for stationary system were found to be 26% and 62.5% respectively and 34% and 82% for tracking system. The GCR (Ground Cover Ratio) for a stationary system is 0.7, which corresponds to a tilt angle of 24°. The GCR for tracking system was found to be 0.12. The estimated ground area needed to build a 50MW PV plant amounts to approx. 0.55km2 for a stationary PV field constituted by HIT PV arrays and approx. 91MW/ km2. In case of a tracker PV field, the required ground area amounts approx.2.4km2 and approx. 20.5MW/ km2.
Abstract: A meta-analysis may be performed using aggregate data (AD) or an individual patient data (IPD). In practice, studies may be available at both IPD and AD level. In this situation, both the IPD and AD should be utilised in order to maximize the available information. Statistical advantages of combining the studies from different level have not been fully explored. This study aims to quantify the statistical benefits of including available IPD when conducting a conventional summary-level meta-analysis. Simulated meta-analysis were used to assess the influence of the levels of data on overall meta-analysis estimates based on IPD-only, AD-only and the combination of IPD and AD (mixed data, MD), under different study scenario. The percentage relative bias (PRB), root mean-square-error (RMSE) and coverage probability were used to assess the efficiency of the overall estimates. The results demonstrate that available IPD should always be included in a conventional meta-analysis using summary level data as they would significantly increased the accuracy of the estimates.On the other hand, if more than 80% of the available data are at IPD level, including the AD does not provide significant differences in terms of accuracy of the estimates. Additionally, combining the IPD and AD has moderating effects on the biasness of the estimates of the treatment effects as the IPD tends to overestimate the treatment effects, while the AD has the tendency to produce underestimated effect estimates. These results may provide some guide in deciding if significant benefit is gained by pooling the two levels of data when conducting meta-analysis.
Abstract: Two new algorithms for nonparametric estimation of errors-in-variables models are proposed. The first algorithm is based on penalized regression spline. The spline is represented as a piecewise-linear function and for each linear portion orthogonal regression is estimated. This algorithm is iterative. The second algorithm involves locally weighted regression estimation. When the independent variable is measured with error such estimation is a complex nonlinear optimization problem. The simulation results have shown the advantage of the second algorithm under the assumption that true smoothing parameters values are known. Nevertheless the use of some indexes of fit to smoothing parameters selection gives the similar results and has an oversmoothing effect.
Abstract: Tidal power can play a vital role in integrating as new source of renewable energy to the off-grid power connection in isolated areas, namely Sandwip, in Bangladesh. It can reduce the present energy crisis and improve the social, environmental and economic perspective of Bangladesh. Tidal energy is becoming popular around the world due to its own facilities. The development of any country largely depends on energy sector improvement. Lack of energy sector is because of hampering progress of any country development, and the energy sector will be stable by only depend on sustainable energy sources. Renewable energy having environmental friendly is the only sustainable solution of secure energy system. Bangladesh has a huge potential of tidal power at different locations, but effective measures on this issue have not been considered sincerely. This paper summarizes the current energy scenario, and Bangladesh can produce power approximately 53.19 MW across the country to reduce the growing energy demand utilizing tidal energy as well as it is shown that Sandwip is highly potential place to produce tidal power, which is estimated approximately 16.49 MW by investing only US $10.37 million. Besides this, cost management for tidal power plant has been also discussed.
Abstract: In this paper, a fifth order propagator operators are proposed for estimating the Angles Of Arrival (AOA) of narrowband electromagnetic waves impinging on antenna array when its number of sensors is larger than the number of radiating sources.
The array response matrix is partitioned into five linearly dependent phases to construct the noise projector using five different propagators from non diagonal blocks of the spectral matrice of the received data; hence, five different estimators are proposed to estimate the angles of the sources. The simulation results proved the performance of the proposed estimators in the presence of white noise comparatively to high resolution eigen based spectra.
Abstract: In recent years, geographic information systems (GIS)
and remote sensing using has increased to estimate runoff catchment.
In this research, runoff curve number maps for captive catchment of
Tehran by helping GIS and also remote sensing which based on
factors such as vegetation, lands using, group of soil hydrology and
hydrological conditions were obtained. Runoff curve numbers map
was obtained by combining these maps in ARC GIS and SCS table.
To evaluate the accuracy of the results, the maximum flow rate of
flood which was obtained from curve numbers, was compared with
the measured maximum flood rate at the watershed outlet and
correctness of curve numbers were approved.
Abstract: Localization of mobile robots are important tasks for
developing autonomous mobile robots. This paper proposes a method
to estimate positions of a mobile robot using a omnidirectional
camera on the robot. Landmarks for points of references are set
up on a field where the robot works. The omnidirectional camera
which can obtain 360 [deg] around images takes photographs of
these landmarks. The positions of the robots are estimated from
directions of these landmarks that are extracted from the images
by image processing. This method can obtain the robot positions
without accumulative position errors. Accuracy of the estimated
robot positions by the proposed method are evaluated through some
experiments. The results show that it can obtain the positions with
small standard deviations. Therefore the method has possibilities of
more accurate localization by tuning of appropriate offset parameters.
Abstract: This paper proposes a GLMM with spatial and
temporal effects for malaria data in Thailand. A Bayesian method is
used for parameter estimation via Gibbs sampling MCMC. A
conditional autoregressive (CAR) model is assumed to present the
spatial effects. The temporal correlation is presented through the
covariance matrix of the random effects. The malaria quarterly data
have been extracted from the Bureau of Epidemiology, Ministry of
Public Health of Thailand. The factors considered are rainfall and
temperature. The result shows that rainfall and temperature are
positively related to the malaria morbidity rate. The posterior means
of the estimated morbidity rates are used to construct the malaria
maps. The top 5 highest morbidity rates (per 100,000 population) are
in Trat (Q3, 111.70), Chiang Mai (Q3, 104.70), Narathiwat (Q4,
97.69), Chiang Mai (Q2, 88.51), and Chanthaburi (Q3, 86.82).
According to the DIC criterion, the proposed model has a better
performance than the GLMM with spatial effects but without
temporal terms.
Abstract: This paper presents a comparative study between two
neural network models namely General Regression Neural Network
(GRNN) and Back Propagation Neural Network (BPNN) are used
to estimate radial overcut produced during Electrical Discharge
Machining (EDM). Four input parameters have been employed:
discharge current (Ip), pulse on time (Ton), Duty fraction (Tau) and
discharge voltage (V). Recently, artificial intelligence techniques, as
it is emerged as an effective tool that could be used to replace
time consuming procedures in various scientific or engineering
applications, explicitly in prediction and estimation of the complex
and nonlinear process. The both networks are trained, and the
prediction results are tested with the unseen validation set of the
experiment and analysed. It is found that the performance of both the
networks are found to be in good agreement with average percentage
error less than 11% and the correlation coefficient obtained for the
validation data set for GRNN and BPNN is more than 91%. However,
it is much faster to train GRNN network than a BPNN and GRNN is
often more accurate than BPNN. GRNN requires more memory space
to store the model, GRNN features fast learning that does not require
an iterative procedure, and highly parallel structure. GRNN networks
are slower than multilayer perceptron networks at classifying new
cases.
Abstract: This paper describes a blind algorithm, which is
compared with two another algorithms proposed in the literature,
for estimating of the minimum phase channel parameters. In order to
identify blindly the impulse response of these channels, we have used
Higher Order Statistics (HOS) to build our algorithm. The simulation
results in noisy environment, demonstrate that the proposed method
could estimate the phase and magnitude with high accuracy of these
channels blindly and without any information about the input, except
that the input excitation is identically and independent distribute
(i.i.d) and non-Gaussian.
Abstract: Regular exercise promotes reduction in blood pressure, reduction in body weight and it also helps to increase in insulin sensitivity. Participation in physical activity should always be linked to medical screening which can reveal serious medical problems. One of them is high blood pressure. Hypertension is risk factor for one billion people worldwide and the highest prevalence is found in Africa. Another component of hypertension is that people who suffer from hypertension have no symptoms. It is estimated that reduction of 3mm Hg in Systolic Blood Pressure decreases cardiac morbidity at least 5%. The most of the guidelines suggest aerobic exercise in a prevention of cardiovascular diseases. On the other hand, it is important to emphasize the impact of resistance training. Even, it was found higher effect for reduction on the level of systolic blood pressure than aerobic exercise.