Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: Two commercial proteases from Bacillus
licheniformis (Alcalase 2.4 L FG and Alcalase 2.5 L, Type DX) were
screened for the production of Z-Ala-Phe-NH2 in batch reaction.
Alcalase 2.4 L FG was the most efficient enzyme for the C-terminal
amidation of Z-Ala-Phe-OMe using ammonium carbamate as
ammonium source. Immobilization of protease has been achieved by
the sol-gel method, using dimethyldimethoxysilane (DMDMOS) and
tetramethoxysilane (TMOS) as precursors (unpublished results). In
batch production, about 95% of Z-Ala-Phe-NH2 was obtained at
30°C after 24 hours of incubation. Reproducibility of different
batches of commercial Alcalase 2.4 L FG preparations was also
investigated by evaluating the amidation activity and the entrapment
yields in the case of immobilization. A packed-bed reactor (0.68 cm
ID, 15.0 cm long) was operated successfully for the continuous
synthesis of peptide amides. The immobilized enzyme retained the
initial activity over 10 cycles of repeated use in continuous reactor at
ambient temperature. At 0.75 mL/min flow rate of the substrate
mixture, the total conversion of Z-Ala-Phe-OMe was achieved after 5
hours of substrate recycling. The product contained about 90%
peptide amide and 10% hydrolysis byproduct.
Abstract: In this paper, the direct AnsAz method is used for constructing the multi-wave solutions to the (2+1)-dimensional extension of the Korteweg de-Vries (shortly EKdV) equation. A new breather type of three-wave solutions including periodic breather type soliton solution, breather type of two-solitary solution are obtained. Some cases with specific values of the involved parameters are plotted for each of the three-wave solutions. Mechanical features of resonance interaction among the multi-wave are discussed. These results enrich the variety of the dynamics of higher-dimensional nonlinear wave field.
Abstract: The current study begins with an awareness that
today-s media environment is characterized by technological
development and a new way of reading caused by the introduction of
the Internet. The researcher conducted a meta analysis framed within
Technological Determinism to investigate the process of hypertext
reading, its differences from linear reading and the effects such
differences can have on people-s ways of mentally structuring their
world. The relationship between literacy and the comprehension
achieved by reading hypertexts is also investigated. The results show
hypertexts are not always user friendly. People experience hyperlinks
as interruptions that distract their attention generating comprehension
and disorientation. On one hand hypertextual jumping reading
generates interruptions that finally make people lose their
concentration. On the other hand hypertexts fascinate people who
would rather read a document in such a format even though the
outcome is often frustrating and affects their ability to elaborate and
retain information.
Abstract: The background estimation approach using a small
window median filter is presented on the bases of analyzing IR point
target, noise and clutter model. After simplifying the two-dimensional
filter, a simple method of adopting one-dimensional median filter is
illustrated to make estimations of background according to the
characteristics of IR scanning system. The adaptive threshold is used
to segment canceled image in the background. Experimental results
show that the algorithm achieved good performance and satisfy the
requirement of big size image-s real-time processing.
Abstract: Many methods exist for either measuring or estimating
evaporation from free water surfaces. Evaporation pans provide one
of the simplest, inexpensive, and most widely used methods of
estimating evaporative losses. In this study, the rate of evaporation
starting from a water surface was calculated by modeling with
application to dams in wet, arid and semi arid areas in Algeria.
We calculate the evaporation rate from the pan using the energy
budget equation, which offers the advantage of an ease of use, but
our results do not agree completely with the measurements taken by
the National Agency of areas carried out using dams located in areas
of different climates. For that, we develop a mathematical model to
simulate evaporation. This simulation uses an energy budget on the
level of a vat of measurement and a Computational Fluid Dynamics
(Fluent). Our calculation of evaporation rate is compared then by the
two methods and with the measures of areas in situ.
Abstract: The problem of frequent pattern discovery is defined
as the process of searching for patterns such as sets of features or items that appear in data frequently. Finding such frequent patterns
has become an important data mining task because it reveals associations, correlations, and many other interesting relationships
hidden in a database. Most of the proposed frequent pattern mining
algorithms have been implemented with imperative programming
languages. Such paradigm is inefficient when set of patterns is large
and the frequent pattern is long. We suggest a high-level declarative
style of programming apply to the problem of frequent pattern
discovery. We consider two languages: Haskell and Prolog. Our
intuitive idea is that the problem of finding frequent patterns should
be efficiently and concisely implemented via a declarative paradigm
since pattern matching is a fundamental feature supported by most
functional languages and Prolog. Our frequent pattern mining
implementation using the Haskell and Prolog languages confirms our
hypothesis about conciseness of the program. The comparative
performance studies on line-of-code, speed and memory usage of
declarative versus imperative programming have been reported in the
paper.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.
Abstract: The availability of water in adequate quantity and
quality is imperative for sustainable development. Worldwide,
significant imbalance exists with regards to sustainable development
particularly from a water and sanitation perspective. Water is a
critical component of public health, and failure to supply safe water
will place a heavy burden on the entire population. Although the 21st
century has witnessed wealth and advanced development, it has not
been realized everywhere. Billions of people are still striving to
access the most basic human needs which are food, shelter, safe
drinking water and adequate sanitation. The global picture conceals
various inequalities particularly with regards to sanitation coverage in
rural and urban areas. Currently, water scarcity and in particular
water governance is the main challenge which will cause a threat to
sustainable development goals. Within the context of water,
sanitation and health, sustainable development is a confusing concept
primarily when examined from the viewpoint of policy options for
developing countries. This perspective paper aims to summarize and
critically evaluate evidence of published studies in relation to water,
sanitation and health and to identify relevant solutions to reduce
public health impacts. Evidently, improving water and sanitation
services will result in significant and lasting gains in health and
economic development.
Abstract: We present design, fabrication, and characterization of
a small (12 mm × 12 mm × 8 mm) movable railway vehicle for sensor
carrying. The miniature railway vehicle (MRV) was mainly composed
of a vibrational structure and three legs. A railway was designed and
fabricated to power and guide the MRV. It also transmits the sensed
data from the MRV to the signal processing unit. The MRV with legs
on the railway was moving due to its high-frequency vibration. A
model was derived to describe the motion. Besides, FEM simulations
were performed to design the legs. Then, the MRV and the railway
were fabricated by precision machining. Finally, an infrared sensor
was carried and tested. The result shows that the MRV without loading
was moving along the railway and its maximum speed was 12.2 mm/s.
Moreover, the testing signal was sensed by the MRV.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: Generator of hypotheses is a new method for data mining. It makes possible to classify the source data automatically and produces a particular enumeration of patterns. Pattern is an expression (in a certain language) describing facts in a subset of facts. The goal is to describe the source data via patterns and/or IF...THEN rules. Used evaluation criteria are deterministic (not probabilistic). The search results are trees - form that is easy to comprehend and interpret. Generator of hypotheses uses very effective algorithm based on the theory of monotone systems (MS) named MONSA (MONotone System Algorithm).
Abstract: Cu-mesoporous TiO2 is developed for removal acid
odor cooperated with ozone assistance and online- regeneration
system with/without UV irradiation (all weather) in study. The results
showed that Cu-mesoporous TiO2 present the desirable adsorption
efficiency of acid odor without UV irradiation, due to the larger
surface area, pore sizeand the additional absorption ability provided by
Cu. In the photocatalysis process, the material structure also benefits
Cu-mesoporous TiO2 to perform the more outstanding efficiency on
degrading acid odor. Cu also postponed the recombination of
electron-hole pairs excited from TiO2 to enhance photodegradation
ability. Cu-mesoporous TiO2 could gain the conspicuous increase on
photocatalysis ability from ozone assistance, but without any benefit
on adsorption. In addition, the online regeneration procedure could
process the used Cu-mesoporous TiO2 to reinstate the adsorption
ability and maintain the photodegradtion performance, depended on
scrubbing, desorping acid odor and reducing Cu to metal state.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: Sophorolipids (SLs) production by the yeast Candida
bombicola was studied in batch shake flasks using synthetic dairy
wastewaters (SDWW) with or without any added external carbon and
nitrogen sources. A maximum SLs production of 38.76 g/l was
observed with the SDWW supplemented with low cost substrate of
sugarcane molasses at 50 g/l and soybean oil at 50 g/l. When the
SDWW was supplemented with more costly glucose, yeast extract,
urea and soybean oil, the production, however, got lowered to only
29.49 g/l, but with a maximum biomass production of 17.38 g/l
together with a complete utilization of the carbon sources.
Abstract: Shear walls are used in most of the tall buildings for
carrying the lateral load. When openings for doors or windows are
necessary to be existed in the shear walls, a special type of the shear
walls is used called "coupled shear walls" which in some cases is
stiffened by specific beams and so, called "stiffened coupled shear
walls".
In this paper, a mathematical method for geometrically nonlinear
analysis of the stiffened coupled shear walls has been presented.
Then, a suitable formulation for determining the critical load of the
stiffened coupled shear walls under gravity force has been proposed.
The governing differential equations for equilibrium and deformation
of the stiffened coupled shear walls have been obtained by setting up
the equilibrium equations and the moment-curvature relationships for
each wall. Because of the complexity of the differential equation, the
energy method has been adopted for approximate solution of the
equations.
Abstract: Encrypted messages sending frequently draws the attention
of third parties, perhaps causing attempts to break and
reveal the original messages. Steganography is introduced to hide
the existence of the communication by concealing a secret message
in an appropriate carrier like text, image, audio or video. Quantum
steganography where the sender (Alice) embeds her steganographic
information into the cover and sends it to the receiver (Bob) over a
communication channel. Alice and Bob share an algorithm and hide
quantum information in the cover. An eavesdropper (Eve) without
access to the algorithm can-t find out the existence of the quantum
message. In this paper, a text quantum steganography technique based
on the use of indefinite articles (a) or (an) in conjunction with the nonspecific
or non-particular nouns in English language and quantum
gate truth table have been proposed. The authors also introduced a
new code representation technique (SSCE - Secret Steganography
Code for Embedding) at both ends in order to achieve high level of
security. Before the embedding operation each character of the secret
message has been converted to SSCE Value and then embeds to cover
text. Finally stego text is formed and transmits to the receiver side.
At the receiver side different reverse operation has been carried out
to get back the original information.
Abstract: The stilling basins are commonly used to dissipate the
energy and protect the downstream floor from erosion. The aim of
the present experimental work is to improve the roughened stilling
basin using T-shape roughness instead of the regular cubic one and
design this new shape. As a result of the present work the best
intensity and the best roughness length are identified. Also, it is
found that the T-shape roughness save materials and reduce the jump
length compared to the cubic one. Sensitivity analysis was performed
and it was noticed that the change in the length of jump is more
sensitive to the change in roughness length than the change in
intensity.
Abstract: Cryptography provides the secure manner of
information transmission over the insecure channel. It authenticates
messages based on the key but not on the user. It requires a lengthy
key to encrypt and decrypt the sending and receiving the messages,
respectively. But these keys can be guessed or cracked. Moreover,
Maintaining and sharing lengthy, random keys in enciphering and
deciphering process is the critical problem in the cryptography
system. A new approach is described for generating a crypto key,
which is acquired from a person-s iris pattern. In the biometric field,
template created by the biometric algorithm can only be
authenticated with the same person. Among the biometric templates,
iris features can efficiently be distinguished with individuals and
produces less false positives in the larger population. This type of iris
code distribution provides merely less intra-class variability that aids
the cryptosystem to confidently decrypt messages with an exact
matching of iris pattern. In this proposed approach, the iris features
are extracted using multi resolution wavelets. It produces 135-bit iris
codes from each subject and is used for encrypting/decrypting the
messages. The autocorrelators are used to recall original messages
from the partially corrupted data produced by the decryption process.
It intends to resolve the repudiation and key management problems.
Results were analyzed in both conventional iris cryptography system
(CIC) and non-repudiation iris cryptography system (NRIC). It
shows that this new approach provides considerably high
authentication in enciphering and deciphering processes.
Abstract: This paper presents a threshold voltage model of pocket implanted sub-100 nm n-MOSFETs incorporating the drain and substrate bias effects using two linear pocket profiles. Two linear equations are used to simulate the pocket profiles along the channel at the surface from the source and drain edges towards the center of the n-MOSFET. Then the effective doping concentration is derived and is used in the threshold voltage equation that is obtained by solving the Poisson-s equation in the depletion region at the surface. Simulated threshold voltages for various gate lengths fit well with the experimental data already published in the literature. The simulated result is compared with the two other pocket profiles used to derive the threshold voltage models of n-MOSFETs. The comparison shows that the linear model has a simple compact form that can be utilized to study and characterize the pocket implanted advanced ULSI devices.