Abstract: In this paper, a comparative performance analysis of
mostly used four nonlinearity cancellation techniques used to realize
the passive resistor by MOS transistors, is presented. The comparison
is done by using an integrator circuit which is employing sequentially
Op-amp, OTRA and ICCII as active element. All of the circuits are
implemented by MOS-C realization and simulated by PSPICE
program using 0.35μm process TSMC MOSIS model parameters.
With MOS-C realization, the circuits became electronically tunable
and fully integrable which is very important in IC design. The output
waveforms, frequency responses, THD analysis results and features
of the nonlinearity cancellation techniques are also given.
Abstract: CuO thin films were deposited by spray ultrasonic
pyrolysis with different precursor solution. Two staring solution slats
were used namely: copper acetate and copper chloride. The influence
of these solutions on CuO thin films proprieties of is instigated. The
X rays diffraction (XDR) analysis indicated that the films deposed
with copper acetate are amorphous however the films elaborated with
copper chloride have monoclinic structure. UV- Visible transmission
spectra showed a strong absorbance of the deposited CuO thin films
in the visible region. Electrical characterization has shown that CuO
thin films prepared with copper acetate have a higher electrical
conductivity.
Abstract: The measurement of organ radiation exposure dose is
one of the most important steps to be taken initially, for developing a
new radiopharmaceutical. In this study, the dosimetric studies of a
novel agent for SPECT-imaging of the bone metastasis, 111In-
1,4,7,10-tetraazacyclododecane-1,4,7,10 tetraethylene phosphonic
acid (111In-DOTMP) complex, have been carried out to estimate the
dose in human organs based on the data derived from rats. The
radiolabeled complex was prepared with high radiochemical purity in
the optimal conditions. Biodistribution studies of the complex was
investigated in the male Syrian rats at selected times after injection
(2, 4, 24 and 48 h). The human absorbed dose estimation of the
complex was made based on data derived from the rats by the
radiation absorbed dose assessment resource (RADAR) method.
111In-DOTMP complex was prepared with high radiochemical purity
of >99% (ITLC). Total body effective absorbed dose for 111In-
DOTMP was 0.061 mSv/MBq. This value is comparable to the other
111In clinically used complexes. The results show that the dose with
respect to the critical organs is satisfactory within the acceptable
range for diagnostic nuclear medicine procedures. Generally, 111In-
DOTMP has interesting characteristics and can be considered as a
viable agent for SPECT-imaging of the bone metastasis in the near
future.
Abstract: The subject of this paper is to review, comparative
analysis and simulation of selected components of power electronic
systems (PES), consistent with the concept of a more electric aircraft
(MEA). Comparative analysis and simulation in software
environment MATLAB / Simulink were carried out on the base of a
group of representatives of civil aircraft (B-787, A-380) and military
(F-22 Raptor, F-35) in the context of multi-pulse converters used in
them (6- and 12-pulse, and 18- and 24-pulse), which are key
components of high-tech electronics on-board power systems of
autonomous power systems (ASE) of modern aircraft (airplanes of
the future).
Abstract: Here, we have shown the reaction of [Cr(ArN(CH2)3NAr)2Cl2] (1) where (Ar = 2,6-Pri
2C6H3) and in presence of NaCp (2) (Cp= C5H5 = cyclopentadien), with a center
coordination η5 interaction between Cp as co-ligand and chromium
metal center, for optimization we used density functional theory
(DFT), under methods, explicitly including electrons correlations, for
the final calculations as MB3LYP (Becke) (Lee–Yang–Parr) level of
theory we used to obtain more exact results. This complex was
calculated as electronic energy for molecular system, because the
calculation accounting all electrons correlations interactions. The
optimised of [Cr(ArN(CH2)3NAr)2(η5-Cp)] (Ar = 2,6-Pri2C6H3 and Cp = C5H5) was found to be thermally stable. By using Dewar-Chatt-Duncanson model, as a basis of the molecular orbital (MO) analysis
and showed the highest occupied molecular orbital (HOMO) and
lowest occupied molecular orbital LUMO.
Abstract: The aim of the study is to compare behavioral and
EEG reactions in Turkic-speaking inhabitants of Siberia (Tuvinians
and Yakuts) and Russians during the recognition of syntax errors in
native and foreign languages. Sixty-three healthy aboriginals of the
Tyva Republic, 29 inhabitants of the Sakha (Yakutia) Republic, and
55 Russians from Novosibirsk participated in the study. EEG were
recorded during execution of error-recognition task in Russian and
English language (in all participants) and in native languages
(Tuvinian or Yakut Turkic-speaking inhabitants). Reaction time (RT)
and quality of task execution were chosen as behavioral measures.
Amplitude and cortical distribution of P300 and P600 peaks of ERP
were used as a measure of speech-related brain activity. In Tuvinians,
there were no differences in the P300 and P600 amplitudes as well as
in cortical topology for Russian and Tuvinian languages, but there
was a difference for English. In Yakuts, the P300 and P600
amplitudes and topology of ERP for Russian language were the same
as Russians had for native language. In Yakuts, brain reactions during
Yakut and English language comprehension had no difference, while
the Russian language comprehension was differed from both Yakut
and English. We found out that the Tuvinians recognized both Russian and
Tuvinian as native languages, and English as a foreign language. The
Yakuts recognized both English and Yakut as foreign languages, but
Russian as a native language. According to the inquirer, both
Tuvinians and Yakuts use the national language as a spoken
language, whereas they do not use it for writing. It can well be a
reason that Yakuts perceive the Yakut writing language as a foreign
language while writing Russian as their native.
Abstract: Evolutionary Algorithms (EAs) have been used
widely through evolution theory to discover acceptable solutions that
corresponds to challenges such as natural resources management.
EAs are also used to solve varied problems in the real world. EAs
have been rapidly identified for its ease in handling multiple
objective problems. Reservoir operations is a vital and researchable
area which has been studied in the last few decades due to the limited
nature of water resources that is found mostly in the semi-arid
regions of the world. The state of some developing economy that
depends on electricity for overall development through hydropower
production, a renewable form of energy, is appalling due to water
scarcity. This paper presents a review of the applications of
evolutionary algorithms to reservoir operation for hydropower
production. This review includes the discussion on areas such as
genetic algorithm, differential evolution, and reservoir operation. It
also identified the research gaps discovered in these areas. The results
of this study will be an eye opener for researchers and decision
makers to think deeply of the adverse effect of water scarcity and
drought towards economic development of a nation. Hence, it
becomes imperative to identify evolutionary algorithms that can
address this issue which can hamper effective hydropower
generation.
Abstract: A numerical study is made in a parallel-plate porous
channel subjected to an oscillating flow and an exothermic chemical
reaction on its walls. The flow field in the porous region is modeled
by the Darcy–Brinkman–Forchheimer model and the finite volume
method is used to solve the governing equations. The effects of the
modified Frank-Kamenetskii (FKm) and Damköhler (Dm) numbers,
the amplitude of oscillation (A), and the Strouhal number (St) are
examined. The main results show an increase of heat and mass
transfer rates with A and St, and their decrease with FKm and Dm.
Abstract: Parboiled rice was developed to produce rice, which
has a low glycemic index for diabetics. However, diabetics also have
a chromium (Cr) deficiency. Thus, it is important to fortify rice with
Cr to increase the Cr content. Moreover, parboiled rice becomes
rancid easily and has a musty odor, rendering the rice unfavorable.
Natural herbs such as pandan leaves (Pandanus amaryllifolius
Roxb.), bay leaves (Syzygium polyanthum [Wigh] Walp) and
cinnamon bark powder (Cinnamomon cassia) are commonly added to
food as aroma enhancers. Previous research has shown that these
herbs could improve insulin sensitivity. The purpose of this study
was to evaluate the effect of herbal extract coatings on the cooking
quality and the preference level of chromium fortified - parboiled rice
(CFPR). The rice grain variety used for this experiment was Ciherang
and the fortificant was CrCl3. The three herbal extracts used for
coating the CFPR were cinnamon, pandan and bay leaf, with
concentration variations of 3%, 6%, and 9% (w/w) for each of the
extracts. The samples were analyzed for their alkali spreading value,
cooking time, elongation, water uptake ratio, solid loss, colour and
lightness; and their sensory properties were determined by means of
an organoleptic test. The research showed that coating the CFPR with
pandan and cinnamon extracts at a concentration of 3% each
produced a preferred CFPR. When coated with those herbal extracts
the CFPR had the following cooking quality properties: alkali
spreading value 5 (intermediate gelatinization temperature), cooking
time, 26-27 min, color value, 14.95-15.00, lightness, 42.30 – 44.06,
elongation, 1.53 – 1.54, water uptake ratio , 4.05-4.06, and solid loss,
0.09/100 g – 0.13 g/100 g.
Abstract: People, throughout the history, have made estimates
and inferences about the future by using their past experiences.
Developing information technologies and the improvements in the
database management systems make it possible to extract useful
information from knowledge in hand for the strategic decisions.
Therefore, different methods have been developed. Data mining by
association rules learning is one of such methods. Apriori algorithm,
one of the well-known association rules learning algorithms, is not
commonly used in spatio-temporal data sets. However, it is possible
to embed time and space features into the data sets and make Apriori
algorithm a suitable data mining technique for learning spatiotemporal
association rules. Lake Van, the largest lake of Turkey, is a
closed basin. This feature causes the volume of the lake to increase or
decrease as a result of change in water amount it holds. In this study,
evaporation, humidity, lake altitude, amount of rainfall and
temperature parameters recorded in Lake Van region throughout the
years are used by the Apriori algorithm and a spatio-temporal data
mining application is developed to identify overflows and newlyformed
soil regions (underflows) occurring in the coastal parts of
Lake Van. Identifying possible reasons of overflows and underflows
may be used to alert the experts to take precautions and make the
necessary investments.
Abstract: The critical concern of satellite operations is to ensure
the health and safety of satellites. The worst case in this perspective
is probably the loss of a mission, but the more common interruption
of satellite functionality can result in compromised mission
objectives. All the data acquiring from the spacecraft are known as
Telemetry (TM), which contains the wealth information related to the
health of all its subsystems. Each single item of information is
contained in a telemetry parameter, which represents a time-variant
property (i.e. a status or a measurement) to be checked. As a
consequence, there is a continuous improvement of TM monitoring
systems to reduce the time required to respond to changes in a
satellite's state of health. A fast conception of the current state of the
satellite is thus very important to respond to occurring failures.
Statistical multivariate latent techniques are one of the vital learning
tools that are used to tackle the problem above coherently.
Information extraction from such rich data sources using advanced
statistical methodologies is a challenging task due to the massive
volume of data. To solve this problem, in this paper, we present a
proposed unsupervised learning algorithm based on Principle
Component Analysis (PCA) technique. The algorithm is particularly
applied on an actual remote sensing spacecraft. Data from the
Attitude Determination and Control System (ADCS) was acquired
under two operation conditions: normal and faulty states. The models
were built and tested under these conditions, and the results show that
the algorithm could successfully differentiate between these
operations conditions. Furthermore, the algorithm provides
competent information in prediction as well as adding more insight
and physical interpretation to the ADCS operation.
Abstract: In this study, the commercial finite element software
ABAQUS was used to develop a three-dimensional nonlinear finite
element model capable of simulating the pull-out test of reinforcing
bars from underwater concrete. The results of thirty-two pull-out tests
that have different parameters were implemented in the software to
study the effect of the concrete cover, the bar size, the use of stirrups,
and the compressive strength of concrete. The interaction properties used in the model provided accurate
results in comparison with the experimental bond-slip results, thus
the model has successfully simulated the pull-out test. The results of
the finite element model are used to better understand and visualize
the distribution of stresses in each component of the model, and to
study the effect of the various parameters used in this study including
the role of the stirrups in preventing the stress from reaching to the
sides of the specimens.
Abstract: Electronic mediums such as websites, feeds, blogs and
social media sites are on a daily basis influencing our decision
making, are improving our productivity and are shaping futures of
many consumers and service/product providers. This research
identifies that both customers and business providers heavily rely on
smart phone applications. Based on this, mobile applications
available on iTunes store were studied. It was identified that fruit and
vegetable related applications used by consumers can broadly be
categorized into purchase applications, diaries, tracking health
applications, trip farm location and cooking applications. On the
other hand, applications used by farmers can broadly be classified as:
weather tracking, pests / fertilizer applications and general social
media applications such as Facebook. To blur this farmer-consumer
application divide, our research utilizes Context Specific
eTransformation Framework and based on it identifies characteristic
future consumer-farmer applications will need to have so that the
current divide can be narrowed and consequently better farmerconsumer
supply chain link established.
Abstract: During machining process, chatter is an unavoidable
phenomenon. Boring bars possess the cantilever shape and due to
this, it is subjected to chatter. The adverse effect of chatter includes
the increase in temperature which will leads to excess tool wear. To
overcome these problems, in this investigation, Cartridge brass (Cu –
70% and Zn – 30%) is passively fixed on the boring bar and also
clearance is provided in order to reduce the displacement, tool wear
and cutting temperature. A conventional all geared lathe is attached
with vibrometer and pyrometer is used to measure the displacement
and temperature. The influence of input parameters such as cutting
speed, depth of cut and clearance on temperature, tool wear and
displacement are investigated for various cutting conditions. From
the result, the optimum conditions to obtain better damping in boring
process for chatter reduction is identified.
Abstract: Hydrogels are three-dimensional, hydrophilic,
polymeric networks composed of homopolymers or copolymers and
are insoluble in water due to the presence of chemical or physical
cross-links. When hydrogels come in contact with aqueous solutions,
they can effectively sorb and retain the dissolved substances,
depending on the nature of the monomeric units comprising the
hydrogel. For this reason, hydrogels have been proposed in several
studies as water purification agents. At the present work anionic
hydrogels bearing negatively charged –COO- groups were prepared
and investigated. These gels are based on sodium acrylate (ANa),
either homopolymerized (poly(sodiumacrylate), PANa) or
copolymerized (P(DMAM-co-ANa)) with N,N Dimethylacrylamide
(DMAM). The hydrogels were used to extract some model organic
dyes from water. It is found that cationic dyes are strongly sorbed and
retained by the hydrogels, while sorption of anionic dyes was
negligible. In all cases it was found that both maximum sorption
capacity and equilibrium binding constant varied from one dye to the
other depending on the chemical structure of the dye, the presence of
functional chemical groups and the hydrophobic-hydrophilic balance.
Finally, the nonionic hydrogel of the homopolymer poly(N,Ndimethylacrylamide),
PDMAM, was also used for reasons of
comparison.
Abstract: This paper presents the advantages of fuzzy control use in technological processes control. The paper presents a real application of the Linguistic Fuzzy-Logic Control, developed at the University of Ostrava for the control of physical models in the Intelligent Systems Laboratory. The paper presents an example of a sensitive non-linear model, such as a magnetic levitation model and obtained results which show how modern information technologies can help to solve actual technical problems. A special method based on the LFLC controller with partial components is presented in this paper followed by the method of automatic context change, which is very helpful to achieve more accurate control results. The main advantage of the used system is its robustness in changing conditions demonstrated by comparing with conventional PID controller. This technology and real models are also used as a background for problem-oriented teaching, realized at the department for master students and their collaborative as well as individual final projects.
Abstract: This paper evaluates the accrual based scheduling for
cloud in single and multi-resource system. Numerous organizations
benefit from Cloud computing by hosting their applications. The
cloud model provides needed access to computing with potentially
unlimited resources. Scheduling is tasks and resources mapping to a
certain optimal goal principle. Scheduling, schedules tasks to virtual
machines in accordance with adaptable time, in sequence under
transaction logic constraints. A good scheduling algorithm improves
CPU use, turnaround time, and throughput. In this paper, three realtime
cloud services scheduling algorithm for single resources and
multiple resources are investigated. Experimental results show
Resource matching algorithm performance to be superior for both
single and multi-resource scheduling when compared to benefit first
scheduling, Migration, Checkpoint algorithms.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive three phase inverter (TPI) for a photovoltaic
(PV) system at commercial level. The proposed model uses phase
locked loop (PLL) to synchronize the TPI with the power electric
grid (PEG) and performs MPC control in a dq reference frame. TPI
model consists of a boost converter (BC), maximum power point
tracking (MPPT) control, and a three-leg voltage source inverter
(VSI). The operational model of VSI is used to synthesize the
sinusoidal current and track the reference. The model is validated
using a 35.7 kW PV system in Matlab/Simulink. Implementation
results show simplicity and accuracy, as well as reliability of the
model.
Abstract: Wheat is the first and the most important grain of the
world and its bakery property is due to glutenin and gliadin qualities.
Wheat seed proteins were divided into four groups according to
solubility including albumin, globulin, glutenin and prolamin or
gliadin. Gliadins are major components of the storage proteins in
wheat endosperm. It seems that little information is available about
gliadin genes in Iranian wild relatives of wheat. Thus, the aim of this
study was the evaluation of the wheat wild relatives collected from
different origins of Zagros Mountains in Iran, in terms of coding
gliadin genes using specific primers. For this, forty accessions of
Triticum boeoticum and Triticum urartu were selected for this study.
For each accession, genomic DNA was extracted and PCRs were
performed in total volumes of 15 μl. The amplification products were
separated on 1.5% agarose gels. In results, for Gli-2A locus three
allelic variants were detected by Gli-2As primer pairs. The sizes of
PCR products for these alleles were 210, 490 and 700 bp. Only five
(13%) and two accessions (5%) produced 700 and 490 bp fragments
when their DNA was amplified with the Gli.As.2 primer pairs.
However, 93% of the accessions carried allele 210 bp, and only 8%
did not any product for this marker. Therefore, these germplasm
could be used as rich gene pool to broaden the genetic base of bread
wheat.
Abstract: Imperialist Competitive Algorithm (ICA) is a recent
meta-heuristic method that is inspired by the social evolutions for
solving NP-Hard problems. The ICA is a population-based algorithm
which has achieved a great performance in comparison to other metaheuristics.
This study is about developing enhanced ICA approach to
solve the Cell Formation Problem (CFP) using sequence data. In
addition to the conventional ICA, an enhanced version of ICA,
namely EICA, applies local search techniques to add more
intensification aptitude and embed the features of exploration and
intensification more successfully. Suitable performance measures are
used to compare the proposed algorithms with some other powerful
solution approaches in the literature. In the same way, for checking
the proficiency of algorithms, forty test problems are presented. Five
benchmark problems have sequence data, and other ones are based on
0-1 matrices modified to sequence based problems. Computational
results elucidate the efficiency of the EICA in solving CFP problems.