Abstract: The large and small-scale shaking table tests, which
was conducted for investigating damage evolution of piles inside
liquefied soil, are numerically simulated and experimental verified by the3D nonlinear finite element analysis. Damage evolution of
elasto-plastic circular steel piles and reinforced concrete (RC) one with cracking and yield of reinforcement are focused on, and the failure patterns and residual damages are captured by the proposed constitutive models. The superstructure excitation behind quay wall is
reproduced as well.
Abstract: Without uncertainty by applying external loads on
beams, bending is created. The created bending in I-beams, puts one
of the flanges in tension and the other one in compression. With increasing of bending, compression flange buckled and beam in out
of its plane direction twisted, this twisting well-known as Lateral Torsional Buckling. Providing bending moment varieties along the
beam, the critical moment is greater than the case its under pure bending. In other words, the value of bending gradient coefficient is
always greater than unite. In this article by the use of " ANSYS 10.0" software near 80 3-D finite element models developed for the
propose of analyzing beams` lateral torsional buckling and surveying influence of slenderness on beams' bending gradient coefficient.
Results show that, presented Cb coefficient via AISC is not correct for some of beams and value of this coefficient is smaller than what proposed by AISC. Therefore instead of using a constant Cb for each
case of loading , a function with two criterion for calculation of Cb coefficient for some cases is proposed.
Abstract: In this paper, the steady-state temperature of a sample 500 KW two rotor one stator Non-slotted axial flux permanent magnet motor is calculated using the finite element simulator software package. Due to the high temperature in various parts of the machine, especially at stator winding, a cooling system is designed for the motor and the temperature is recalculated. The results show that the temperature obtained for the parts is within the permissible range.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: Having considered tactile sensing and palpation of a
surgeon in order to detect kidney stone during open surgery; we
present the 2D model of nephrolithiasis (two dimensional model of
kidney containing a simulated stone). The effects of stone existence
that appear on the surface of kidney (because of exerting mechanical
load) are determined. Using Finite element method, it is illustrated
that the created stress patterns on the surface of kidney and stress
graphs not only show existence of stone inside kidney, but also show
its exact location.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.
Abstract: Manufacturing components of fiber-reinforced
thermoplastics requires three steps: heating the matrix, forming and
consolidation of the composite and terminal cooling the matrix. For
the heating process a pre-determined temperature distribution through
the layers and the thickness of the pre-consolidated sheets is
recommended to enable forming mechanism. Thus, a design for the
heating process for forming composites with thermoplastic matrices
is necessary. To obtain a constant temperature through thickness and
width of the sheet, the heating process was analyzed by the help of
the finite element method. The simulation models were validated by
experiments with resistance thermometers as well as with an infrared
camera. Based on the finite element simulation, heating methods for
infrared radiators have been developed. Using the numeric
simulation many iteration loops are required to determine the process
parameters. Hence, the initiation of a model for calculating relevant
process parameters started applying regression functions.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.
Abstract: Arc welding is an important joining process widely used in many industrial applications including production of automobile, ships structures and metal tanks. In welding process, the moving electrode causes highly non-uniform temperature distribution that leads to residual stresses and different deviations, especially buckling distortions in thin plates. In order to control the deviations and increase the quality of welded plates, a fixture can be used as a practical and low cost method with high efficiency. In this study, a coupled thermo-mechanical finite element model is coded in the software ANSYS to simulate the behavior of thin plates located by a 3-2-1 positioning system during the welding process. Computational results are compared with recent similar works to validate the finite element models. The agreement between the result of proposed model and other reported data proves that finite element modeling can accurately predict the behavior of welded thin plates.
Abstract: The aim of this paper is the analysis and preservation of lime kilns, focusing on the structure, construction, and functionality of vertical shaft lime kilns of the Cap Corse in Corsica. Plans and sections of two lime kilns are presented in detail, providing an overall picture of this specific industrial heritage. The potential damage areas are identified performing structural analysis of a lime kiln using the finite element method. A restoration and strengthening technique that satisfies the directions of the Charter of Venice is presented using post-tensioning tendons. Recommendations are given to preserve and promote these important historical structures integrating them into the custom footpath.
Abstract: We present new finite element methods for Helmholtz and Maxwell equations on general three-dimensional polyhedral meshes, based on domain decomposition with boundary elements on the surfaces of the polyhedral volume elements. The methods use the lowest-order polynomial spaces and produce sparse, symmetric linear systems despite the use of boundary elements. Moreover, piecewise constant coefficients are admissible. The resulting approximation on the element surfaces can be extended throughout the domain via representation formulas. Numerical experiments confirm that the convergence behavior on tetrahedral meshes is comparable to that of standard finite element methods, and equally good performance is attained on more general meshes.
Abstract: Interactive web-based computer simulations are
needed by the medical community to replicate the experience of
surgical procedures as closely and realistically as possible without
the need to practice on corpses, animals and/or plastic models. In this
paper, we offer a review on current state of the research on
simulations of surgical threads, identify future needs and present our
proposed plans to meet them. Our goal is to create a physics-based
simulator, which will predict the behavior of surgical thread when
subjected to conditions commonly encountered during surgery. To
that end, we will i) develop three dimensional finite element models
based on the Cosserat theory of elasticity ii) test and feedback results
with the medical community and iii) develop a web-based user
interface to run/command our simulator and visualize the results. The
impacts of our research are that i) it will contribute to the
development of a new generation of training for medical school
students and ii) the simulator will be useful to expert surgeons in
developing new, better and less risky procedures.
Abstract: Collision is considered as a time-depended nonlinear
dynamic phenomenon. The majority of researchers have focused on
deriving the resultant damage of the ship collisions via analytical,
experimental, and finite element methods.In this paper, first, the
force-penetration curve of a head collision on a container ship with
rigid barrier based on Yang and Pedersen-s methods for internal
mechanic section is studied. Next, the obtained results from different
analytical methods are compared with each others. Then, through a
simulation of the container ship collision in Ansys Ls-Dyna, results
from finite element approach are compared with analytical methods
and the source of errors is discussed. Finally, the effects of
parameters such as velocity, and angle of collision on the forcepenetration
curve are investigated.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: CEMTool is a command style design and analyzing
package for scientific and technological algorithm and a matrix based
computation language. In this paper, we present new 2D & 3D
finite element method (FEM) packages for CEMTool. We discuss
the detailed structures and the important features of pre-processor,
solver, and post-processor of CEMTool 2D & 3D FEM packages. In
contrast to the existing MATLAB PDE Toolbox, our proposed FEM
packages can deal with the combination of the reserved words. Also,
we can control the mesh in a very effective way. With the introduction
of new mesh generation algorithm and fast solving technique, our
FEM packages can guarantee the shorter computational time than
MATLAB PDE Toolbox. Consequently, with our new FEM packages,
we can overcome some disadvantages or limitations of the existing
MATLAB PDE Toolbox.
Abstract: The present article deals with a composite casting process that allows to produce bilayer AlSn6-Al strips based on the technique of horizontal continuous casting. In the first part experimental investigations on the production of a single layer AlSn6 strip are described. Afterwards essential results of basic compound casting trials using simple test specimen are presented to define the thermal conditions required for a metallurgical compound between the alloy AlSn6 and pure aluminium. Subsequently, numerical analyses are described. A finite element model was used to examine a continuous composite casting process. As a result of the simulations the main influencing parameters concerning the thermal conditions within the composite casting region could be pointed out. Finally, basic guidance is given for the design of an appropriate composite mould system.
Abstract: Smoke discharging is a main reason of air pollution
problem from industrial plants. The obstacle of a building has an
affect with the air pollutant discharge. In this research, a mathematical
model of the smoke dispersion from two sources and one source with
a structural obstacle is considered. The governing equation of the
model is an isothermal mass transfer model in a viscous fluid. The
finite element method is used to approximate the solutions of the
model. The triangular linear elements have been used for discretising
the domain, and time integration has been carried out by semi-implicit
finite difference method. The simulations of smoke dispersion in
cases of one chimney and two chimneys are presented. The maximum
calculated smoke concentration of both cases are compared. It is then
used to make the decision for smoke discharging and air pollutant
control problems on industrial area.
Abstract: IPN and IPE sections, which are commonly used European I shapes, are widely used in steel structures as cantilever beams to support overhangs. A considerable number of studies exist on calculating lateral torsional buckling load of I sections. However, most of them provide series solutions or complex closed-form equations. In this paper, a simple equation is presented to calculate lateral torsional buckling load of IPN and IPE section cantilever beams. First, differential equation of lateral torsional buckling is solved numerically for various loading cases. Then a parametric study is conducted on results to present an equation for lateral torsional buckling load of European IPN and IPE beams. Finally, results obtained by presented equation are compared to differential equation solutions and finite element model results. ABAQUS software is utilized to generate finite element models of beams. It is seen that the results obtained from presented equation coincide with differential equation solutions and ABAQUS software results. It can be suggested that presented formula can be safely used to calculate critical lateral torsional buckling load of European IPN and IPE section cantilevers.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.