Abstract: Prediction of maximum local scour is necessary for
the safety and economical design of the bridges. A number of
equations have been developed over the years to predict local scour
depth using laboratory data and a few pier equations have also been
proposed using field data. Most of these equations are empirical in
nature as indicated by the past publications. In this paper attempts
have been made to compute local depth of scour around bridge pier in
dimensional and non-dimensional form by using linear regression,
simple regression and SVM (Poly & Rbf) techniques along with few
conventional empirical equations. The outcome of this study suggests
that the SVM (Poly & Rbf) based modeling can be employed as an
alternate to linear regression, simple regression and the conventional
empirical equations in predicting scour depth of bridge piers. The
results of present study on the basis of non-dimensional form of
bridge pier scour indicate the improvement in the performance of
SVM (Poly & Rbf) in comparison to dimensional form of scour.
Abstract: From the start, the importance of having a plan to
sustain tourism was acknowledged. The correct methods to monitor
that type of tourism have been researched. Thus, we propose in this
work to analyze the applicability of a monitoring and assistance
method on the understanding of the tourism sustainability in a small
size destiny or getaway. In this study, the subject is Lagoa da
Confusão, in the state of Tocantins and the analysis was carried out
through the efficiency of the local indicators, according to the WOT
approach. We concluded that the sustainable tourism key points that
were analyzed demonstrated to be important evaluation and
quantification tools for the proposed tasks to be developed in the
mentioned destiny. This is a study of an interdisciplinary character
and the deductive method was chosen as the guiding line.
Abstract: Abstract—[Tris (1,10-phenanthroline) lanthanum(III)]
trithiocyanate is a new compound that has shown high ability for
stopping the synthesis of DNA and also acting as a photosensitizer.
Nowadays, the radiation dose assessment resource (RADAR) method
is known as the most common method for absorbed dose calculation.
177Lu was produced by (n, gamma) reaction in a research reactor.
177Lu-PL3 was prepared in the optimized condition. The
radiochemical yield was checked by ITLC method. The
biodistribution of the complex was investigated by intravenously
injection to wild-type rats via their tail veins. In this study, the
absorbed dose of 177Lu-PL3 to human organs was estimated by
RADAR method. 177Lu was prepared with a specific activity of 2.6-3
GBq.mg-1 and radionuclide purity of 99.98 %. Final preparation of
the radiolabelled complex showed high radiochemical purity of >
99%. The results show that liver and spleen have received the highest
absorbed dose of 1.051 and 0.441 mSv/MBq, respectively. The
absorbed dose values for these two dose-limiting tissues suggest
more biological studies special in tumor-bearing animals.
Abstract: In this paper, a comparative performance analysis of
mostly used four nonlinearity cancellation techniques used to realize
the passive resistor by MOS transistors, is presented. The comparison
is done by using an integrator circuit which is employing sequentially
Op-amp, OTRA and ICCII as active element. All of the circuits are
implemented by MOS-C realization and simulated by PSPICE
program using 0.35μm process TSMC MOSIS model parameters.
With MOS-C realization, the circuits became electronically tunable
and fully integrable which is very important in IC design. The output
waveforms, frequency responses, THD analysis results and features
of the nonlinearity cancellation techniques are also given.
Abstract: The subject of this paper is to review, comparative
analysis and simulation of selected components of power electronic
systems (PES), consistent with the concept of a more electric aircraft
(MEA). Comparative analysis and simulation in software
environment MATLAB / Simulink were carried out on the base of a
group of representatives of civil aircraft (B-787, A-380) and military
(F-22 Raptor, F-35) in the context of multi-pulse converters used in
them (6- and 12-pulse, and 18- and 24-pulse), which are key
components of high-tech electronics on-board power systems of
autonomous power systems (ASE) of modern aircraft (airplanes of
the future).
Abstract: The aim of the study is to compare behavioral and
EEG reactions in Turkic-speaking inhabitants of Siberia (Tuvinians
and Yakuts) and Russians during the recognition of syntax errors in
native and foreign languages. Sixty-three healthy aboriginals of the
Tyva Republic, 29 inhabitants of the Sakha (Yakutia) Republic, and
55 Russians from Novosibirsk participated in the study. EEG were
recorded during execution of error-recognition task in Russian and
English language (in all participants) and in native languages
(Tuvinian or Yakut Turkic-speaking inhabitants). Reaction time (RT)
and quality of task execution were chosen as behavioral measures.
Amplitude and cortical distribution of P300 and P600 peaks of ERP
were used as a measure of speech-related brain activity. In Tuvinians,
there were no differences in the P300 and P600 amplitudes as well as
in cortical topology for Russian and Tuvinian languages, but there
was a difference for English. In Yakuts, the P300 and P600
amplitudes and topology of ERP for Russian language were the same
as Russians had for native language. In Yakuts, brain reactions during
Yakut and English language comprehension had no difference, while
the Russian language comprehension was differed from both Yakut
and English. We found out that the Tuvinians recognized both Russian and
Tuvinian as native languages, and English as a foreign language. The
Yakuts recognized both English and Yakut as foreign languages, but
Russian as a native language. According to the inquirer, both
Tuvinians and Yakuts use the national language as a spoken
language, whereas they do not use it for writing. It can well be a
reason that Yakuts perceive the Yakut writing language as a foreign
language while writing Russian as their native.
Abstract: Evolutionary Algorithms (EAs) have been used
widely through evolution theory to discover acceptable solutions that
corresponds to challenges such as natural resources management.
EAs are also used to solve varied problems in the real world. EAs
have been rapidly identified for its ease in handling multiple
objective problems. Reservoir operations is a vital and researchable
area which has been studied in the last few decades due to the limited
nature of water resources that is found mostly in the semi-arid
regions of the world. The state of some developing economy that
depends on electricity for overall development through hydropower
production, a renewable form of energy, is appalling due to water
scarcity. This paper presents a review of the applications of
evolutionary algorithms to reservoir operation for hydropower
production. This review includes the discussion on areas such as
genetic algorithm, differential evolution, and reservoir operation. It
also identified the research gaps discovered in these areas. The results
of this study will be an eye opener for researchers and decision
makers to think deeply of the adverse effect of water scarcity and
drought towards economic development of a nation. Hence, it
becomes imperative to identify evolutionary algorithms that can
address this issue which can hamper effective hydropower
generation.
Abstract: A numerical study is made in a parallel-plate porous
channel subjected to an oscillating flow and an exothermic chemical
reaction on its walls. The flow field in the porous region is modeled
by the Darcy–Brinkman–Forchheimer model and the finite volume
method is used to solve the governing equations. The effects of the
modified Frank-Kamenetskii (FKm) and Damköhler (Dm) numbers,
the amplitude of oscillation (A), and the Strouhal number (St) are
examined. The main results show an increase of heat and mass
transfer rates with A and St, and their decrease with FKm and Dm.
Abstract: Parboiled rice was developed to produce rice, which
has a low glycemic index for diabetics. However, diabetics also have
a chromium (Cr) deficiency. Thus, it is important to fortify rice with
Cr to increase the Cr content. Moreover, parboiled rice becomes
rancid easily and has a musty odor, rendering the rice unfavorable.
Natural herbs such as pandan leaves (Pandanus amaryllifolius
Roxb.), bay leaves (Syzygium polyanthum [Wigh] Walp) and
cinnamon bark powder (Cinnamomon cassia) are commonly added to
food as aroma enhancers. Previous research has shown that these
herbs could improve insulin sensitivity. The purpose of this study
was to evaluate the effect of herbal extract coatings on the cooking
quality and the preference level of chromium fortified - parboiled rice
(CFPR). The rice grain variety used for this experiment was Ciherang
and the fortificant was CrCl3. The three herbal extracts used for
coating the CFPR were cinnamon, pandan and bay leaf, with
concentration variations of 3%, 6%, and 9% (w/w) for each of the
extracts. The samples were analyzed for their alkali spreading value,
cooking time, elongation, water uptake ratio, solid loss, colour and
lightness; and their sensory properties were determined by means of
an organoleptic test. The research showed that coating the CFPR with
pandan and cinnamon extracts at a concentration of 3% each
produced a preferred CFPR. When coated with those herbal extracts
the CFPR had the following cooking quality properties: alkali
spreading value 5 (intermediate gelatinization temperature), cooking
time, 26-27 min, color value, 14.95-15.00, lightness, 42.30 – 44.06,
elongation, 1.53 – 1.54, water uptake ratio , 4.05-4.06, and solid loss,
0.09/100 g – 0.13 g/100 g.
Abstract: Software testing has become a mandatory process in
assuring the software product quality. Hence, test management is
needed in order to manage the test activities conducted in the
software test life cycle. This paper discusses on the challenges faced
in the software test life cycle, and how the test processes and test
activities, mainly on test cases creation, test execution, and test
reporting is being managed and automated using several test
automation tools, i.e. Jira, Robot Framework, and Jenkins.
Abstract: The critical concern of satellite operations is to ensure
the health and safety of satellites. The worst case in this perspective
is probably the loss of a mission, but the more common interruption
of satellite functionality can result in compromised mission
objectives. All the data acquiring from the spacecraft are known as
Telemetry (TM), which contains the wealth information related to the
health of all its subsystems. Each single item of information is
contained in a telemetry parameter, which represents a time-variant
property (i.e. a status or a measurement) to be checked. As a
consequence, there is a continuous improvement of TM monitoring
systems to reduce the time required to respond to changes in a
satellite's state of health. A fast conception of the current state of the
satellite is thus very important to respond to occurring failures.
Statistical multivariate latent techniques are one of the vital learning
tools that are used to tackle the problem above coherently.
Information extraction from such rich data sources using advanced
statistical methodologies is a challenging task due to the massive
volume of data. To solve this problem, in this paper, we present a
proposed unsupervised learning algorithm based on Principle
Component Analysis (PCA) technique. The algorithm is particularly
applied on an actual remote sensing spacecraft. Data from the
Attitude Determination and Control System (ADCS) was acquired
under two operation conditions: normal and faulty states. The models
were built and tested under these conditions, and the results show that
the algorithm could successfully differentiate between these
operations conditions. Furthermore, the algorithm provides
competent information in prediction as well as adding more insight
and physical interpretation to the ADCS operation.
Abstract: During machining process, chatter is an unavoidable
phenomenon. Boring bars possess the cantilever shape and due to
this, it is subjected to chatter. The adverse effect of chatter includes
the increase in temperature which will leads to excess tool wear. To
overcome these problems, in this investigation, Cartridge brass (Cu –
70% and Zn – 30%) is passively fixed on the boring bar and also
clearance is provided in order to reduce the displacement, tool wear
and cutting temperature. A conventional all geared lathe is attached
with vibrometer and pyrometer is used to measure the displacement
and temperature. The influence of input parameters such as cutting
speed, depth of cut and clearance on temperature, tool wear and
displacement are investigated for various cutting conditions. From
the result, the optimum conditions to obtain better damping in boring
process for chatter reduction is identified.
Abstract: The last two decades witnessed a movement towards
harmonization of international financial reporting standards (IFRS)
throughout the global economy. This investigation seeks to identify
the factors that could explain the adoption of IFRS by poor
jurisdictions. While there has been a considerable amount of
literature published on the effects and key drivers of IFRS adoption
in both developed and developing countries, little attention has been
paid to jurisdictions with less developed capital markets and low
income levels exclusively. Drawing upon the Institutional Isomorphism theory and analyzing
a sample of 45 poor jurisdictions between 2008 and 2013, the study
empirically shows that poor jurisdictions are driven by legitimacy
concerns rather than by economic reasoning to adopt an international
accounting perspective. This in turn has implications for the IASB, as
it should seek to influence institutional pressures within a particular
jurisdiction in order to promote IFRS adoption.
Abstract: Hydrogels are three-dimensional, hydrophilic,
polymeric networks composed of homopolymers or copolymers and
are insoluble in water due to the presence of chemical or physical
cross-links. When hydrogels come in contact with aqueous solutions,
they can effectively sorb and retain the dissolved substances,
depending on the nature of the monomeric units comprising the
hydrogel. For this reason, hydrogels have been proposed in several
studies as water purification agents. At the present work anionic
hydrogels bearing negatively charged –COO- groups were prepared
and investigated. These gels are based on sodium acrylate (ANa),
either homopolymerized (poly(sodiumacrylate), PANa) or
copolymerized (P(DMAM-co-ANa)) with N,N Dimethylacrylamide
(DMAM). The hydrogels were used to extract some model organic
dyes from water. It is found that cationic dyes are strongly sorbed and
retained by the hydrogels, while sorption of anionic dyes was
negligible. In all cases it was found that both maximum sorption
capacity and equilibrium binding constant varied from one dye to the
other depending on the chemical structure of the dye, the presence of
functional chemical groups and the hydrophobic-hydrophilic balance.
Finally, the nonionic hydrogel of the homopolymer poly(N,Ndimethylacrylamide),
PDMAM, was also used for reasons of
comparison.
Abstract: This paper presents the advantages of fuzzy control use in technological processes control. The paper presents a real application of the Linguistic Fuzzy-Logic Control, developed at the University of Ostrava for the control of physical models in the Intelligent Systems Laboratory. The paper presents an example of a sensitive non-linear model, such as a magnetic levitation model and obtained results which show how modern information technologies can help to solve actual technical problems. A special method based on the LFLC controller with partial components is presented in this paper followed by the method of automatic context change, which is very helpful to achieve more accurate control results. The main advantage of the used system is its robustness in changing conditions demonstrated by comparing with conventional PID controller. This technology and real models are also used as a background for problem-oriented teaching, realized at the department for master students and their collaborative as well as individual final projects.
Abstract: Revenue leakages are one of the major challenges
manufacturers face in production processes, as most of the input
materials that should emanate as products from the lines are lost as
waste. Rather than generating income from material input which is
meant to end-up as products, losses are further incurred as costs in
order to manage waste generated. In addition, due to the lack of a
clear view of the flow of resources on the lines from input to output
stage, acquiring information on the true cost of waste generated have
become a challenge. This has therefore given birth to the
conceptualization and implementation of waste minimization
strategies by several manufacturing industries. This paper reviews the
principles and applications of three environmental management
accounting tools namely Activity-based Costing (ABC), Life-Cycle
Assessment (LCA) and Material Flow Cost Accounting (MFCA) in
the manufacturing industry and their effectiveness in curbing revenue
leakages. The paper unveils the strengths and limitations of each of
the tools; beaming a searchlight on the tool that could allow for
optimal resource utilization, transparency in production process as
well as improved cost efficiency. Findings from this review reveal
that MFCA may offer superior advantages with regards to the
provision of more detailed information (both in physical and
monetary terms) on the flow of material inputs throughout the
production process compared to the other environmental accounting
tools. This paper therefore makes a case for the adoption of MFCA as
a viable technique for the identification and reduction of waste in
production processes, and also for effective decision making by
production managers, financial advisors and other relevant
stakeholders.
Abstract: Wheat is the first and the most important grain of the
world and its bakery property is due to glutenin and gliadin qualities.
Wheat seed proteins were divided into four groups according to
solubility including albumin, globulin, glutenin and prolamin or
gliadin. Gliadins are major components of the storage proteins in
wheat endosperm. It seems that little information is available about
gliadin genes in Iranian wild relatives of wheat. Thus, the aim of this
study was the evaluation of the wheat wild relatives collected from
different origins of Zagros Mountains in Iran, in terms of coding
gliadin genes using specific primers. For this, forty accessions of
Triticum boeoticum and Triticum urartu were selected for this study.
For each accession, genomic DNA was extracted and PCRs were
performed in total volumes of 15 μl. The amplification products were
separated on 1.5% agarose gels. In results, for Gli-2A locus three
allelic variants were detected by Gli-2As primer pairs. The sizes of
PCR products for these alleles were 210, 490 and 700 bp. Only five
(13%) and two accessions (5%) produced 700 and 490 bp fragments
when their DNA was amplified with the Gli.As.2 primer pairs.
However, 93% of the accessions carried allele 210 bp, and only 8%
did not any product for this marker. Therefore, these germplasm
could be used as rich gene pool to broaden the genetic base of bread
wheat.
Abstract: The health care must be a right for people around the
world, but in order to guarantee the access to all, it is necessary to
overcome geographical barriers. Telemedicine take advantage of
Information Communication Technologies to deploy health care
services around the world. To achieve those goals, it is necessary to
use existing last mile solution to create access for home users, which
is why is necessary to establish the channel characteristics for those
kinds of services. This paper presents an analysis of network
performance of last mile solution for the use of IPTV broadcasting
with the application of streaming for telemedicine apps.
Abstract: The UK is leading in online retail and mobile
adoption. However, there is a dearth of information relating to mobile
apparel retail, and developing an understanding about consumer
browsing and purchase behaviour in m-retail channel would provide
apparel marketers, mobile website and app developers with the
necessary understanding of consumers’ needs. Despite the rapid
growth of mobile retail businesses, no published study has examined
shopping behaviour on fashion mobile apps and websites. A mixed method approach helped to understand why fashion
consumers prefer websites on smartphones, when diverse mobile
apps are also available. The following research methods were
employed: survey, eye-tracking experiments, observation, and
interview with retrospective think aloud. The mobile gaze tracking
device by SensoMotoric Instruments was used to understand
frustrations in navigation and other issues facing consumers in
mobile channel. This method helped to validate and compliment
other traditional user-testing approaches in order to optimize user
experience and enhance the development of mobile retail channel.
The study involved eight participants - females aged 18 to 35 years
old, who are existing mobile shoppers. The participants used the
Topshop mobile app and website on a smart phone to complete a task
according to a specified scenario leading to a purchase. The
comparative study was based on: duration and time spent at different
stages of the shopping journey, number of steps involved and product
pages visited, search approaches used, layout and visual clues, as
well as consumer perceptions and expectations. The results from the data analysis show significant differences in
consumer behaviour when using a mobile app or website on a smart
phone. Moreover, two types of problems were identified, namely
technical issues and human errors. Having a mobile app does not
guarantee success in satisfying mobile fashion consumers. The
differences in the layout and visual clues seem to influence the
overall shopping experience on a smart phone. The layout of search
results on the website was different from the mobile app. Therefore,
participants, in most cases, behaved differently on different
platforms. The number of product pages visited on the mobile app
was triple the number visited on the website due to a limited visibility
of products in the search results. Although, the data on traffic trends
held by retailers to date, including retail sector breakdowns for visits
and views, data on device splits and duration, might seem a valuable
source of information, it cannot explain why consumers visit many
product pages, stay longer on the website or mobile app, or abandon
the basket. A comprehensive list of pros and cons was developed by
highlighting issues for website and mobile app, and recommendations
provided. The findings suggest that fashion retailers need to be aware of
actual consumers’ behaviour on the mobile channel and their expectations in order to offer a seamless shopping experience. Added
to which is the challenge of retaining existing and acquiring new
customers. There seem to be differences in the way fashion
consumers search and shop on mobile, which need to be explored in
further studies.
Abstract: In this study, students’ learning has been investigated
and satisfaction in one of the course offered at Qatar University
Foundation Program. Innovative teaching has been implied
methodology that emphasizes on enhancing students’ thinking skills,
decision making, and problem solving skills. Some interesting results
were found which could be used to further improvement of the
teaching methodology. In Fall 2012 in Foundation Program Math
department at Qatar University has started implementing new ways
of teaching Math by introducing MyMathLab (MML) as an
innovative interactive tool in addition of the use Blackboard to
support standard teaching such as Discussion board in Virtual class to
engage students outside of classroom and to enhance independent,
active learning that promote students’ critical thinking skills, decision
making, and problem solving skills through the learning process.