Abstract: Natural gas sweetening process is a controlled process that must be done at maximum efficiency and with the highest quality. In this work, due to complexity and non-linearity of the process, the H2S gas separation and the intelligent fuzzy controller, which is used to enhance the process, are simulated in MATLAB – Simulink. New design of fuzzy control for Gas Separator is discussed in this paper. The design is based on the utilization of linear state-estimation to generate the internal knowledge-base that stores input-output pairs. The obtained input/output pairs are then used to design a feedback fuzzy controller. The proposed closed-loop fuzzy control system maintains the system asymptotically-stability while it enhances the system time response to achieve better control of the concentration of the output gas from the tower. Simulation studies are carried out to illustrate the Gas Separator system performance.
Abstract: Reinforced concrete (RC) shear wall system of residential buildings is popular in South Korea. RC walls are subjected to axial forces in common and the effect of axial forces on the strength loss of the fire damaged walls has not been investigated. This paper aims at investigating temperature distribution on fire damaged concrete walls having different axial loads. In the experiments, a variable of specimens is axial force ratio. RC walls are fabricated with 150mm of wall thicknesses, 750mm of lengths and 1,300mm of heights having concrete strength of 24MPa. After curing, specimens are heated on one surface with ISO-834 standard time-temperature curve for 2 hours and temperature distributions during the test are measured using thermocouples inside the walls. The experimental results show that the temperature of the RC walls exposed to fire increases as axial force ratio increases. To verify the experiments, finite element (FE) models are generated for coupled temperature-structure analyses. The analytical results of thermal behaviors are in good agreement with the experimental results. The predicted displacement of the walls decreases when the axial force increases.
Abstract: In subjective terms, Polish SME sector occupies a
prominent position in the national economic development, in which
planning of the management strategies should be primarily based on
identifying and meeting the innovation needs. As a research sample, there is chosen a printing sector of industry.
SMEs share in printing sector in Poland is estimated at the level of
81% of all enterprises. In recent years, the printing industry achieved
one of the highest levels of EU support in Poland. There is a
relatively high increase in the development of technological
innovations in equipment and the associated significant increase in
production capacity. It can be also noticed that on average, every
third enterprise belonging to the printing industry has implemented
innovations, but not all of them effected in better economic results.
Therefore, the aim of this article is to evaluate the impact of the
implementation of innovation projects financed from the EU funds
for performance of SMEs in the printing industry. As the results of research of EU funds co-financing effects on the
development of innovation in the printing industry, it was specified
that examined SMEs prefer to implement product innovation to
receive a grant to the project at a level between 40% to 60%, the
remaining part of the investment is usually covered with equity. The most common type of innovation had indicated a single
implementation, related only to the change in process, technology, or
organization. The relationship between variables of the EU funds and
management of innovative activities was verified. It has been
observed that the identified variables arising from the support in a
form of the EU funds had a positive effect on the level of earned
revenue, the increase in margin and in increase in employment as
well. It was confirmed that the implemented innovations supported
by the European funds have a positive impact on the performance of
the printing companies. Although there is a risk that due to the
decreasing demand for printing services such a high level of funding
the companies in this sector will significantly increase competition in
the long term, that may also contribute to the economic problems of
the enterprises belonging to the analyzed branch.
Abstract: Critical success factors (CSFs) and the criteria to measure project success have received much attention over the decades and are among the most widely researched topics in the context of project management. However, although there have been extensive studies on the subject by different researchers, to date, there has been little agreement on the CSFs. The aim of this study is to identify the CSFs that influence the performance of construction projects, and determine their relative importance for different objectives across five stages in the project life cycle. A considerable literature review was conducted that resulted in the identification of 179 individual factors. These factors were then grouped into nine major categories. A questionnaire survey was used to collect data from three groups of respondents: client representatives, consultants, and contractors. Out of 164 questionnaires distributed, 93 were returned, yielding a response rate of 56.7%. Using the mean score, relative importance index, and weighted average method, the top 10 critical factors for each category were identified. The agreement of survey respondents on those categorised factors were analysed using Spearman’s rank correlation. A one-way analysis of variance was then performed to determine whether the mean scores among the various groups of respondents were statistically significant. The findings indicate the most CSFs in each category in procurement phase are: proper procurement programming of materials (time), stability in the price of materials (cost), and determining quality in the construction (quality). They are then followed by safety equipment acquisition and maintenance (health and safety), budgeting allowed in a contractual arrangement for implementing environmental management activities (environment), completeness of drawing documents (productivity), accurate measurement and pricing of bill of quantities (risk management), adequate communication among the project team (human resource), and adequate cost control measures (client satisfaction). An understanding of CSFs would help all interested parties in the construction industry to improve project performance. Furthermore, the results of this study would help construction professionals and practitioners take proactive measures for effective project management.
Abstract: Comparative analysis of robotic vehicles for pipe inspection is presented in this paper. The promising concept of self-propelled intelligent robotic vehicle (SPIRV) based on octahedral dodekapod for inspection and operation in active branched pipelines with variable cross-sections is reasoned. SPIRV is able to move in pipeline, regardless of its spatial orientation. SPIRV can also be used to move along the outside of the pipelines as well as in space between surfaces of annular tubes. Every one of faces of the octahedral dodekapod can clamp/unclamp a thing with a closed loop surface of various forms as well as put pressure on environmental surface of contact. These properties open new possibilities for its applications in SPIRV. We examine design principles of octahedral dodekapod as future intelligent building blocks for various robotic vehicles that can self-move and self-reconfigure.
Abstract: Automatic License plate recognition (ALPR) is a technology which recognizes the registration plate or number plate or License plate of a vehicle. In this paper, an Indian vehicle number plate is mined and the characters are predicted in efficient manner. ALPR involves four major technique i) Pre-processing ii) License Plate Location Identification iii) Individual Character Segmentation iv) Character Recognition. The opening phase, named pre-processing helps to remove noises and enhances the quality of the image using the conception of Morphological Operation and Image subtraction. The second phase, the most puzzling stage ascertain the location of license plate using the protocol Canny Edge detection, dilation and erosion. In the third phase, each characters characterized by Connected Component Approach (CCA) and in the ending phase, each segmented characters are conceptualized using cross correlation template matching- a scheme specifically appropriate for fixed format. Major application of ALPR is Tolling collection, Border Control, Parking, Stolen cars, Enforcement, Access Control, Traffic control. The database consists of 500 car images taken under dissimilar lighting condition is used. The efficiency of the system is 97%. Our future focus is Indian Vehicle License Plate Validation (Whether License plate of a vehicle is as per Road transport and highway standard).
Abstract: This work studies the effect of thickness on structural
and electrical properties of CuAlS2 thin films grown by two stage
vacuum thermal evaporation technique. CuAlS2 thin films of
thicknesses 50nm, 100nm and 200nm were deposited on suitably
cleaned corning 7059 glass substrate at room temperature (RT). In
the first stage Cu-Al precursors were grown at room temperature by
thermal evaporation and in the second stage Cu-Al precursors were
converted to CuAlS2 thin films by sulfurisation under sulfur
atmosphere at the temperature of 673K. The structural properties of
the films were examined by X-ray diffraction (XRD) technique while
electrical properties of the specimens were studied using four point
probe method. The XRD studies revealed that the films are of
crystalline in nature having tetragonal structure. The variations of the
micro-structural parameters, such as crystallite size (D), dislocation
density ( ), and micro-strain ( ), with film thickness were
investigated. The results showed that the crystallite sizes increase as
the thickness of the film increases. The dislocation density and
micro-strain decreases as the thickness increases. The resistivity ( )
of CuAlS2 film is found to decrease with increase in film thickness,
which is related to the increase of carrier concentration with film
thickness. Thus thicker films exhibit the lowest resistivity and high
carrier concentration, implying these are the most conductive films.
Low electrical resistivity and high carrier concentration are widely
used as the essential components in various optoelectronic devices
such as light-emitting diode and photovoltaic cells.
Abstract: In this paper, we present an analytical method for
analysis of nano-scale spherical shell subjected to thermo-mechanical
shocks based on nonlocal elasticity theory. Thermo-mechanical
properties of nano shpere is assumed to be temperature dependent.
Governing partial differential equation of motion is solved
analytically by using Laplace transform for time domain and power
series for spacial domain. The results in Laplace domain is
transferred to time domain by employing the fast inverse Laplace
transform (FLIT) method. Accuracy of present approach is assessed
by comparing the the numerical results with the results of published
work in literature. Furtheremore, the effects of non-local parameter
and wall thickness on the dynamic characteristics of the nano-sphere
are studied.
Abstract: Since the advent of the law 86/14 concerning the
exploitation of the national territory by foreign companies in
partnership with the Algerian oil and gas company, the problem of
hydrocarbons metering in the sharing production come out.
More generally, good management counting hydrocarbons can
provide data on the production wells, the field and the reservoir for
medium and long term planning, particularly in the context of the
management and field development.
In this work, we are interested in the transactional metering which
is a very delicate and crucial period in the current context of the new
hydrocarbon’s law characterized by assets system between the
various activities of Sonatrach and its foreign partners.
After a state of the art on hydrocarbons metering devices in
Algeria and elsewhere, we will decline the advantages and
disadvantages of each system, and then we describe the problem to
try to reach an optimal solution.
Abstract: Pipelines are extensively used engineering structures
which convey fluid from one place to another. Most of the time,
pipelines are placed underground and are encumbered by soil weight
and traffic loads. Corrosion of pipe material is the most common
form of pipeline deterioration and should be considered in both the
strength and serviceability analysis of pipes.
The study in this research focuses on concrete pipes in sewage
systems (concrete sewers). This research firstly investigates how to
involve the effect of corrosion as a time dependent process of
deterioration in the structural and failure analysis of this type of pipe.
Then three probabilistic time dependent reliability analysis methods
including the first passage probability theory, the gamma distributed
degradation model and the Monte Carlo simulation technique are
discussed and developed. Sensitivity analysis indexes which can be
used to identify the most important parameters that affect pipe failure
are also discussed.
The reliability analysis methods developed in this paper contribute
as rational tools for decision makers with regard to the strengthening
and rehabilitation of existing pipelines. The results can be used to
obtain a cost-effective strategy for the management of the sewer
system.
Abstract: Not all proteins have the same nutritional value, since
protein quality strongly depends on its amino acid composition and
digestibility. The meat of game animals could be a high protein
source because of its well-balanced essential amino acids
composition. Investigations about biochemical composition of game
meat such as wild boar (Sus scrofa scrofa), roe deer (Capreolus
capreolus) and beaver (Castor fiber) are not very much. Therefore,
the aim of the investigation was evaluate protein composition of
game meat hunted in Latvia. The biochemical analysis, evaluation of
connective tissue and essential amino acids in meat samples were
done, the amino acids score were calculate. Results of analysis
showed that protein content 20.88-22.05% of all types of meat
samples is not different statistically. The content of connective tissue
from 1.3% in roe deer till 1.5% in beaver meat allowed classified
game animal as high quality meat. The sum of essential amino acids
in game meat samples were determined 7.05–8.26g100g-1. Roe deer
meat has highest protein content and lowest content of connective
tissues among game meat hunted in Latvia. Concluded that amino
acid score for limiting amino acids phenylalanine and tyrosine is high
and shows high biological value of game meat.
Abstract: This paper has focused on the most important parameters in the LSC uptake; inlet Re number and Sc number in the presence of non-uniform magnetic field. The magnetic field is arising from the thin wire with electric current placed vertically to the arterial blood vessel. According to the results of this study, applying magnetic field can be a treatment for atherosclerosis by reducing LSC along the vessel wall. Homogeneous porous layer as a arterial wall has been regarded. Blood flow has been considered laminar and incompressible containing Ferro fluid (blood and 4 % vol. Fe3O4) under steady state conditions. Numerical solution of governing equations was obtained by using the single-phase model and control volume technique for flow field.
Abstract: Problem of food preservation is extremely important
for mankind. Viscous damage ("illness") of bread results from
development of Bacillus spp. bacteria. High temperature resistant
spores of this microorganism are steady against 120°C) and remain in
bread during pastries, potentially causing spoilage of the final
product. Scientists are interested in further characterization of bread
spoiling Bacillus spp. species. Our aim was to find weather yeast
Saccharomyces cerevisiae strains that are able to produce natural
antimicrobial killer factor can preserve bread illness. By diffusion
method, we showed yeast antagonistic activity against spore-forming
bacteria. Experimental technological parameters were the same as for
bakers' yeasts production on the industrial scale. Risograph test
during dough fermentation demonstrated gas production. The major
finding of the study was a clear indication of the presence of killer
yeast strain antagonistic activity against rope in bread causing
bacteria. After demonstrating antagonistic effect of S. cerevisiae on
bacteria using solid nutrient medium, we tested baked bread under
provocative conditions. We also measured formation of carbon
dioxide in the dough, dough-making duration and quality of the final
products, when using different strains of S. cerevisiae. It is
determined that the use of yeast S. cerevisiae RCAM 01730 killer
strain inhibits appearance of rope in bread. Thus, natural yeast
antimicrobial killer toxin, produced by some S. cerevisiae strains is
an anti-rope in bread protector.
Abstract: Experiments were performed to investigate the effects of roughness on the reattachment and redevelopment regions over a 12 mm forward facing step (FFS) in an open channel flow. The experiments were performed over an upstream smooth wall and a smooth FFS, an upstream wall coated with sandpaper 36 grit and a smooth FFS and an upstream rough wall produced from sandpaper 36 grit and a FFS coated with sandpaper 36 grit. To investigate only the wall roughness effects, Reynolds number, Froude number, aspect ratio and blockage ratio were kept constant. Upstream profiles showed reduced streamwise mean velocities close to the rough wall compared to the smooth wall, but the turbulence level was increased by upstream wall roughness. The reattachment length for the smooth-smooth wall experiment was 1.78h; however, when it is replaced with rough-smooth wall the reattachment length decreased to 1.53h. It was observed that the upstream roughness increased the physical size of contours of maximum turbulence level; however, the downstream roughness decreased both the size and magnitude of contours in the vicinity of the leading edge of the step. Quadrant analysis was performed to investigate the dominant Reynolds shear stress contribution in the recirculation region. The Reynolds shear stress and turbulent kinetic energy profiles after the reattachment showed slower recovery compared to the streamwise mean velocity, however all the profiles fairly collapse on their corresponding upstream profiles at x/h = 60. It was concluded that to obtain a complete collapse several more streamwise distances would be required.
Abstract: Knowledge transfer between personnel could benefit an organization’s improved competitive advantage in the marketplace from a strategic approach to knowledge management. The lack of information sharing between personnel could create knowledge transfer gaps while restricting the decision-making processes. Knowledge transfer between personnel can potentially improve information sharing based on an implemented knowledge management strategy. An organization’s capacity to gain more knowledge is aligned with the organization’s prior or existing captured knowledge. This case study attempted to understand the overall influence of a KMS within the corporate environment and knowledge exchange between personnel. The significance of this study was to help understand how organizations can improve the Return on Investment (ROI) of a knowledge management strategy within a knowledge-centric organization. A qualitative descriptive case study was the research design selected for this study. The lack of information sharing between personnel may create knowledge transfer gaps while restricting the decision-making processes. Developing a knowledge management strategy acceptable at all levels of the organization requires cooperation in support of a common organizational goal. Working with management and executive members to develop a protocol where knowledge transfer becomes a standard practice in multiple tiers of the organization. The knowledge transfer process could be measurable when focusing on specific elements of the organizational process, including personnel transition to help reduce time required understanding the job. The organization studied in this research acknowledged the need for improved knowledge management activities within the organization to help organize, retain, and distribute information throughout the workforce. Data produced from the study indicate three main themes including information management, organizational culture, and knowledge sharing within the workforce by the participants. These themes indicate a possible connection between an organizations KMS, the organizations culture, knowledge sharing, and knowledge transfer.
Abstract: The aim of this study is to compare abused and normal male students in Tehran guidance schools with emphasis on the co-dependency of their mothers. The method of this study is based on survey method and comparison (Ex-Post Facto). The method of sampling is also multi-stage cluster. Accordingly, we did sampling from secondary schools of education and training in Tehran, including 12 schools with levels of first, second and third. Each of the schools represents the three – high, medium and low- economic and social conditions. In the following, three classes from every school and 20 students from each class were randomly selected. By (CTQ) abused and normal students were separated that 670 children were recognized as normal and 50 children as abused. Then, 50 children were randomly selected from normal group and compared with abused group. Using Spanned-Fischer Co-dependency Scale, we compared mothers of abused and normal students. The results showed that mothers of the abused children have higher co- dependency average comparing to the mothers of the normal children.
Abstract: The purpose of this study is to investigate the efficacy of the solution-focused brief therapy on improving the psychological wellbeing of family supervisor woman. This study has been carried out by semi-experimental method and in the form of pre-test, post-test performance on two groups (experimental and control), so that one sample group of 30 individuals was randomly achieved and were randomly divided in two groups of experimental (n=15) and control (n=15). To collect data, Ryff scale psychological wellbeing was used. After conducting pre-test (RSPWB) for two experimental and control groups, Solution-focused brief therapy interference was conducted on the experimental group during five two-hour sessions. Finally, Ryff scale psychological wellbeing was reused for the two groups as post-test and achieved outcomes that were analyzed using covariance. The results indicated that the significant increase of average marks of the experimental group in psychological wellbeing had better function than that of the control group. Finally, solution-focused brief therapy for improving psychological well-being of family supervisor women has a suitable capability and could be used in this way.
Abstract: The purpose of this study is to investigate the efficacy of solution-focused group therapy on improving the depressed mothers of child abuser families. This study was carried out in the form of a semi-pilot, pre-test and post-test on two groups (experimental and control). Subjects include all mothers and their children that are the members of Shush and Naser Khosro child home. Beck Depression Inventory and Child Trauma Questionnaire were used to collect data. First, child abuse questionnaire was completed by children, Then Beck Depression Inventory was completed by their mothers that 22 of them were recognized as depressed and randomly divided in two groups of experimental and control. After applying pre-test for both of these groups, the intervention of solution- focused group therapy was performed in five sessions on experimental group. Finally, post-test was applied on both groups and subsequently in a month, follow-up test was performed. T-test, multivariate variance, and repeated measurement analysis of variance were used to analyze the data. According to the findings, it can be concluded that this therapy leads to the improvement of depressed mother's mood. As a result, the intervention of solution-focused group therapy is useful in order to improve the depressing mood of mothers of child abuser families.
Abstract: Sclareolide is made from sclareol by oxidiative synthesis and subsequent crystallization, while the crystallization mother liquor still contains 15%~30%wt of sclareolide to be reclaimed. With the reaction material of sclareol is provided as plant extract, many sorts of complex impurities exist in the mother liquor. Due to the difficulty in recycling sclareolide after solvent recovery, it is common practice for the factories to discard the mother liquor, which not only results in loss of sclareolide, but also contributes extra environmental burden. In this paper, a process based on adsorption and elution has been presented for recycling of sclareolide from mother liquor. After pretreatment of the crystallization mother liquor by HZ-845 resin to remove parts of impurities, sclareolide is adsorbed by HZ-816 resin. The HZ-816 resin loaded with sclareolide is then eluted by elution solvent. Finally, the eluent containing sclareolide is concentrated and fed into the crystallization step in the process. By adoption of the recycle from mother liquor, total yield of sclareolide increases from 86% to 90% with a stable purity of the final sclareolide products maintained.
Abstract: To increase the quality of learning, teacher and learner need mutual effort for realization of educational value. For this purpose, we need to manage the co-creational education among teacher and learners. In this research, we try to find a feature of co-creational education. To be more precise, we analyzed learners’ reports by natural language processing, and extract some features that describe the state of the co-creational education.