Abstract: This study presents a simulation model for converting coal to methanol, based on gasification technology with the commercial chemical process simulator, Pro/II® V8.1.1. The methanol plant consists of air separation unit (ASU), gasification unit, gas clean-up unit, and methanol synthetic unit. The clean syngas is produced with the first three operating units, and the model has been verified with the reference data from United States Environment Protection Agency. The liquid phase methanol (LPMEOHTM) process is adopted in the methanol synthetic unit. Clean syngas goes through gas handing section to reach the reaction requirement, reactor loop/catalyst to generate methanol, and methanol distillation to get desired purity over 99.9 wt%. The ratio of the total energy combined with methanol and dimethyl ether to that of feed coal is 78.5% (gross efficiency). The net efficiency is 64.2% with the internal power consumption taken into account, based on the assumption that the efficiency of electricity generation is 40%.
Abstract: Many multimedia communication applications require a
source to transmit messages to multiple destinations subject to quality
of service (QoS) delay constraint. To support delay constrained
multicast communications, computer networks need to guarantee an
upper bound end-to-end delay from the source node to each of
the destination nodes. This is known as multicast delay problem.
On the other hand, if the same message fails to arrive at each
destination node at the same time, there may arise inconsistency and
unfairness problem among users. This is related to multicast delayvariation
problem. The problem to find a minimum cost multicast
tree with delay and delay-variation constraints has been proven to
be NP-Complete. In this paper, we propose an efficient heuristic
algorithm, namely, Economic Delay and Delay-Variation Bounded
Multicast (EDVBM) algorithm, based on a novel heuristic function,
to construct an economic delay and delay-variation bounded multicast
tree. A noteworthy feature of this algorithm is that it has very high
probability of finding the optimal solution in polynomial time with
low computational complexity.
Abstract: A mathematical model based on a mass and energy
balance for the combustion in a cement rotary kiln was developed.
The model was used to investigate the impact of replacing about
45 % of the primary coal energy by different alternative fuels.
Refuse derived fuel, waste wood, solid hazardous waste and liquid
hazardous waste were used in the modeling. The results showed that
in order to keep the kiln temperature unchanged, and thereby
maintain the required clinker quality, the production capacity had to
be reduced by 1-15 %, depending on the fuel type. The reason for the
reduction is increased exhaust gas flow rates caused by the fuel
characteristics. The model, which has been successfully validated in a
full-scale experiment, was also used to show that the negative impact
on the production capacity can be avoided if a relatively small part of
the combustion air is replaced by pure oxygen.
Abstract: The main goal of this seminal paper is to introduce the
application of Wireless Sensor Networks (WSN) in long distance
infrastructure monitoring (in particular in pipeline infrastructure
monitoring) – one of the on-going research projects by the Wireless
Communication Research Group at the department of Electronic and
Computer Engineering, Nnamdi Azikiwe University, Awka. The
current sensor network architectures for monitoring long distance
pipeline infrastructures are previewed. These are wired sensor
networks, RF wireless sensor networks, integrated wired and wireless
sensor networks. The reliability of these architectures is discussed.
Three reliability factors are used to compare the architectures in
terms of network connectivity, continuity of power supply for the
network, and the maintainability of the network. The constraints and
challenges of wireless sensor networks for monitoring and protecting
long distance pipeline infrastructure are discussed.
Abstract: The way music is interpreted by the human brain is a very interesting topic, but also an intricate one. Although this domain has been studied for over a century, many gray areas remain in the understanding of music. Recent advances have enabled us to perform accurate measurements of the time taken by the human brain to interpret and assimilate a sound. Cognitive computing provides tools and development environments that facilitate human cognition simulation. ACT-R is a cognitive architecture which offers an environment for implementing human cognitive tasks. This project combines our understanding of the music interpretation by a human listener and the ACT-R cognitive architecture to build SINGER, a computerized simulation for listening and recalling songs. The results are similar to human experimental data. Simulation results also show how it is easier to remember short melodies than long melodies which require more trials to be recalled correctly.
Abstract: This work presents a methodology for the design and
manufacture of propellers oriented to the experimental verification of
theoretical results based on the combined model. The design process
begins by using algorithms in Matlab which output data contain the
coordinates of the points that define the blade airfoils, in this case the
NACA 6512 airfoil was used. The modeling for the propeller blade
was made in NX7, through the imported files in Matlab and with the
help of surfaces. Later, the hub and the clamps were also modeled.
Finally, NX 7 also made possible to create post-processed files to the
required machine. It is possible to find the block of numbers with G
& M codes about the type of driver on the machine. The file
extension is .ptp. These files made possible to manufacture the blade,
and the hub of the propeller.
Abstract: A strip domain decomposition parallel algorithm for fast direct Poisson solver is presented on a 3D Cartesian staggered grid. The parallel algorithm follows the principles of sequential algorithm for fast direct Poisson solver. Both Dirichlet and Neumann boundary conditions are addressed. Several test cases are likewise addressed in order to shed light on accuracy and efficiency in the strip domain parallelization algorithm. Actually the current implementation shows a very high efficiency when dealing with a large grid mesh up to 3.6 * 109 under massive parallel approach, which explicitly demonstrates that the proposed algorithm is ready for massive parallel computing.
Abstract: In this paper we investigate the watermarking authentication when applied to medical imagery field. We first give an overview of watermarking technology by paying attention to fragile watermarking since it is the usual scheme for authentication.We then analyze the requirements for image authentication and integrity in medical imagery, and we show finally that invertible schemes are the best suited for this particular field. A well known authentication method is studied. This technique is then adapted here for interleaving patient information and message authentication code with medical images in a reversible manner, that is using lossless compression. The resulting scheme enables on a side the exact recovery of the original image that can be unambiguously authenticated, and on the other side, the patient information to be saved or transmitted in a confidential way. To ensure greater security the patient information is encrypted before being embedded into images.
Abstract: Defense and Aerospace environment is continuously
striving to keep up with increasingly sophisticated Information
Technology (IT) in order to remain effective in today-s dynamic and
unpredictable threat environment. This makes IT one of the largest
and fastest growing expenses of Defense. Hundreds of millions of
dollars spent a year on IT projects. But, too many of those millions
are wasted on costly mistakes. Systems that do not work properly,
new components that are not compatible with old ones, trendy new
applications that do not really satisfy defense needs or lost through
poorly managed contracts.
This paper investigates and compiles the effective strategies that
aim to end exasperation with low returns and high cost of
Information Technology acquisition for defense; it tries to show how
to maximize value while reducing time and expenditure.
Abstract: Scolothrips longicornis Priesner is one of the
important predators of tetranychid mites with a wide distribution
throughout Iran. Life table and population growth parameters of S.
longicornis feeding on two-spotted spider mite, Tetranychus
turkestani Ugarov & Nikolski were investigated under laboratory
condition (26±1ºC, 65±5% R.H. and 16L: 8D). To carry of these
experiments, S. longicornis collections reared on cowpea infested
with T. turkestani were prepared. The eggs with less than 24 hours
old were selected and reared. The emerged larvae feeding directly on
cowpea leaf discs which were infested with T. turkestani. Thirty
females of S. longicornis with 24 hours age were selected and
released on infested leaf discs. They replaced daily to a new leaf disc
and the laying eggs have counted. The experiment continued till the
last thrips had died. The result showed that the mean age mortality of
the adult female thrips were between 21-25 days which is nearly
equal life expectancy (ex) at the time of adult eclosion. Parameters
related to reproductive table including gross reproductive rate, net
reproductive rate, intrinsic rate of natural increase and finite rate of
increase were 48.91, 37.63, 0.26 and 2.3, respectively. Mean age per
female/day, mean fertile egg per female/day, gross hatch rate, mean
net age fertility, mean net age fecundity, net fertility rate and net
fecundity rate were 2.23, 1.76, 0.87, 13.87, 14.26, 69.1 and 78.5,
respectively. Sex ratio of offspring also recorded daily. The highest
sex ratio for females was 0.88 in first day of oviposition. The sex
ratio decreased gradually and reached under 0.46 after the day 26 and
the oviposition rate declined. Then it seems that maintenance of
rearing culture of predatory thrips for mass rearing later than 26 days
after egg-laying commence is not profitable.
Abstract: This paper presents the system identification by
physical-s law method and designs the controller for the Azimuth
Angle Control of the Platform of the Multi-Launcher Rocket System
(MLRS) by Root Locus technique. The plant mathematical model
was approximated using MATLAB for simulation and analyze the
system. The controller proposes the implementation of PID
Controller using Programmable Logic Control (PLC) for control the
plant. PID Controllers are widely applicable in industrial sectors and
can be set up easily and operate optimally for enhanced productivity,
improved quality and reduce maintenance requirement. The results
from simulation and experiments show that the proposed a PID
Controller to control the elevation angle that has superior control
performance by the setting time less than 12 sec, the rise time less
than 1.6 sec., and zero steady state. Furthermore, the system has a
high over shoot that will be continue development.
Abstract: The heat storage capacity of concrete in building shells is a major reason for excessively large electricity consumption induced by indoor air conditioning. In this research, the previously developed Smart Temperature Information Material (STIM) is embedded in two groups of exterior wall specimens (the control group contains reinforced concrete exterior walls and the experimental group consists of tiled exterior walls). Long term temperature measurements within the concrete are taken by the embedded STIM. Temperature differences between the control group and the experimental group in walls facing the four cardinal directions (east, west, south, and north) are evaluated. This study aims to provide a basic reference for the design of exterior walls and the selection of heat insulation materials.
Abstract: In the past few years, the use of wireless sensor networks (WSNs) potentially increased in applications such as intrusion detection, forest fire detection, disaster management and battle field. Sensor nodes are generally battery operated low cost devices. The key challenge in the design and operation of WSNs is to prolong the network life time by reducing the energy consumption among sensor nodes. Node clustering is one of the most promising techniques for energy conservation. This paper presents a novel clustering algorithm which maximizes the network lifetime by reducing the number of communication among sensor nodes. This approach also includes new distributed cluster formation technique that enables self-organization of large number of nodes, algorithm for maintaining constant number of clusters by prior selection of cluster head and rotating the role of cluster head to evenly distribute the energy load among all sensor nodes.
Abstract: In the past, there were more researches of recommendation system in applied electronic commerce. However, because all circles promote information technology integrative instruction actively, the quantity of instruction resources website is more and more increasing on the Internet. But there are less website including recommendation service, especially for teachers. This study established an instruction resource recommendation website that analyzed teaching style of teachers, then provided appropriate instruction resources for teachers immediately. We used the questionnaire survey to realize teacher-s suggestions and satisfactions with the instruction resource contents and recommendation results. The study shows: (1)The website used “Transactional Ability Inventory" that realized teacher-s style and provided appropriate instruction resources for teachers in a short time, it reduced the step of data filter. (2)According to the content satisfaction of questionnaire survey, four styles teachers were almost satisfied with the contents of the instruction resources that the website recommended, thus, the conception of developing instruction resources with different teaching style is accepted. (3) According to the recommendation satisfaction of questionnaire survey, four styles teachers were almost satisfied with the recommendation service of the website, thus, the recommendation strategy that provide different results for teachers in different teaching styles is accepted.
Abstract: This paper presents a design of source encoding
calculator software which applies the two famous algorithms in the
field of information theory- the Shannon-Fano and the Huffman
schemes. This design helps to easily realize the algorithms without
going into a cumbersome, tedious and prone to error manual
mechanism of encoding the signals during the transmission. The
work describes the design of the software, how it works, comparison
with related works, its efficiency, its usefulness in the field of
information technology studies and the future prospects of the
software to engineers, students, technicians and alike. The designed
“Encodia" software has been developed, tested and found to meet the
intended requirements. It is expected that this application will help
students and teaching staff in their daily doing of information theory
related tasks. The process is ongoing to modify this tool so that it can
also be more intensely useful in research activities on source coding.
Abstract: For about two decades scientists have been
developing techniques for enhancing the quality of medical images
using Fourier transform, DWT (Discrete wavelet transform),PDE
model etc., Gabor wavelet on hexagonal sampled grid of the images
is proposed in this work. This method has optimal approximation
theoretic performances, for a good quality image. The computational
cost is considerably low when compared to similar processing in the
rectangular domain. As X-ray images contain light scattered pixels,
instead of unique sigma, the parameter sigma of 0.5 to 3 is found to
satisfy most of the image interpolation requirements in terms of high
Peak Signal-to-Noise Ratio (PSNR) , lower Mean Squared Error
(MSE) and better image quality by adopting windowing technique.
Abstract: A fast adaptive Tomlinson Harashima (T-H) precoder structure is presented for indoor wireless communications, where the channel may vary due to rotation and small movement of the mobile terminal. A frequency-selective slow fading channel which is time-invariant over a frame is assumed. In this adaptive T-H precoder, feedback coefficients are updated at the end of every uplink frame by using system identification technique for channel estimation in contrary with the conventional T-H precoding concept where the channel is estimated during the starting of the uplink frame via Wiener solution. In conventional T-H precoder it is assumed the channel is time-invariant in both uplink and downlink frames. However assuming the channel is time-invariant over only one frame instead of two, the proposed adaptive T-H precoder yields better performance than conventional T-H precoder if the channel is varied in uplink after receiving the training sequence.
Abstract: A multilayer self organizing neural neural network
(MLSONN) architecture for binary object extraction, guided by a beta
activation function and characterized by backpropagation of errors
estimated from the linear indices of fuzziness of the network output
states, is discussed. Since the MLSONN architecture is designed to
operate in a single point fixed/uniform thresholding scenario, it does
not take into cognizance the heterogeneity of image information in
the extraction process. The performance of the MLSONN architecture
with representative values of the threshold parameters of the beta
activation function employed is also studied. A three layer bidirectional
self organizing neural network (BDSONN) architecture
comprising fully connected neurons, for the extraction of objects from
a noisy background and capable of incorporating the underlying image
context heterogeneity through variable and adaptive thresholding,
is proposed in this article. The input layer of the network architecture
represents the fuzzy membership information of the image scene to
be extracted. The second layer (the intermediate layer) and the final
layer (the output layer) of the network architecture deal with the self
supervised object extraction task by bi-directional propagation of the
network states. Each layer except the output layer is connected to the
next layer following a neighborhood based topology. The output layer
neurons are in turn, connected to the intermediate layer following
similar topology, thus forming a counter-propagating architecture
with the intermediate layer. The novelty of the proposed architecture
is that the assignment/updating of the inter-layer connection weights
are done using the relative fuzzy membership values at the constituent
neurons in the different network layers. Another interesting feature
of the network lies in the fact that the processing capabilities of
the intermediate and the output layer neurons are guided by a beta
activation function, which uses image context sensitive adaptive
thresholding arising out of the fuzzy cardinality estimates of the
different network neighborhood fuzzy subsets, rather than resorting to
fixed and single point thresholding. An application of the proposed
architecture for object extraction is demonstrated using a synthetic
and a real life image. The extraction efficiency of the proposed
network architecture is evaluated by a proposed system transfer index
characteristic of the network.
Abstract: The goal of steganography is to avoid drawing
suspicion to the transmission of a hidden message. If suspicion is
raised, steganography may fail. The success of steganography
depends on the secrecy of the action. If steganography is detected,
the system will fail but data security depends on the robustness of the
applied algorithm. In this paper, we propose a novel plausible
deniability scheme in steganography by using a diversionary message
and encrypt it with a DES-based algorithm. Then, we compress the
secret message and encrypt it by the receiver-s public key along with
the stego key and embed both messages in a carrier using an
embedding algorithm. It will be demonstrated how this method can
support plausible deniability and is robust against steganalysis.
Abstract: As German companies roll out their standardized
production systems to offshore manufacturing plants, they face the
challenge of implementing them in different cultural environments.
Studies show that the local adaptation is one of the key factors for a
successful implementation. Thus the question arises of where the line
between standardization and adaptation can be drawn. To answer
this question the influence of culture on production systems is
analysed in this paper. The culturally contingent components of
production systems are identified. Also the contingency factors are
classified according to their impact on the necessary adaptation
changes and implementation effort. Culturally specific decision
making, coordination, communication and motivation patterns
require one-time changes in organizational and process design. The
attitude towards rules requires more intense coaching and controlling.
Lastly a framework is developed to depict standardization and
adaption needs when transplanting production systems into different
cultural environments.