Abstract: This article proposes a hybrid algorithm for spectrum
allocation in cognitive radio networks based on the algorithms
Analytical Hierarchical Process (AHP) and Technique for Order of
Preference by Similarity to Ideal Solution (TOPSIS) to improve the
performance of the spectrum mobility of secondary users in cognitive
radio networks. To calculate the level of performance of the proposed algorithm a
comparative analysis between the proposed AHP-TOPSIS, Grey
Relational Analysis (GRA) and Multiplicative Exponent Weighting
(MEW) algorithm is performed. Four evaluation metrics are used.
These metrics are accumulative average of failed handoffs,
accumulative average of handoffs performed, accumulative average
of transmission bandwidth, and accumulative average of the
transmission delay. The results of the comparison show that AHP-TOPSIS Algorithm
provides 2.4 times better performance compared to a GRA Algorithm
and, 1.5 times better than the MEW Algorithm.
Abstract: At a global level, water stewardship, water stress and
water security are crucial factors in tourism planning and
development considerations. Challenges associated with water is of
particular concern to the Maldives as there is limited availability of
freshwater, high dependency on desalinated water, and high unit cost
associated with desalinating water. While the Maldives is promoted
as an example of sustainable tourism, a key sustainability challenge
facing tourism dependent communities is the efficient use and
management of available water resources. A water crisis event in the
capital island of Maldives highlighted how precarious water related
issues are in this tourism dependent destination. Applying
netnography, the focus of this working paper is to present community
perceptions of how government policies addressed Malé Water and
Sewerage Company (MWSC) water crisis event.
Abstract: This paper presents a case study of using STATCOM to enhance the performance of Al-Qatraneh 33-kV transmission line. The location of the STATCOM was identified by maintaining minimum voltage drops at the 110 load nodes. The transmission line and the 110 load nodes have been modeled by MATLAB/Simulink. The suggested STATCOM and its location will increase the transmission capability of this transmission line and overcome the overload expected in the year 2020. The annual percentage loading rise has been considered as 14.35%. A graphical representation of the line-to-line voltages and the voltage drops at different load nodes is illustrated.
Abstract: This qualitative case study seeks to understand and
explain the deployment of radio frequency identification (RFID)
systems in two countries (i.e., in Taiwan for the adoption of electric
scooters and in Finland for supporting glass bottle recycling) using
the “Technology-Organization-Environment” theoretical framework.
This study also seeks to highlight the relevance and importance of
pursuing environmental sustainability in firms and in society in
general due to the social urgency of the issues involved.
Abstract: Intermediate cities which also called medium size
cities have an important role in the process of globalization. It is
argued that, in some cases this type of cities may be depopulated or in
otherwise may be transformed as the periphery of metropolitans, so
that the personal identity of the city and its local cultural heritage
could suffer from its neighbor metropolitan. Over the last decades,
the role of tourism in the development process and the cultural
heritage has increased. The impact of tourism on socioeconomic
growth makes motivation for the study of tourism development in
regional and urban planning process. There are evidences that
tourism has a positive impact in local development and makes
economic motivations for cultural heritage protection. In this study,
by considering the role of tourism in local development, especially by
its economic and socio-cultural impacts, it is tried to introduce a
strategy for tourism development through a method of urban planning
for intermediate cities called as Base plan. Damavand is an
intermediate city located in Tehran province, Iran with a high
potential in tourism by its local specific characteristic like social
structure, antiquities and natural attractions. It’s selected as a suitable
case study for intended strategy which is a combination of urban
planning and tourism development methods. Focusing on recognition
of the historical and cultural heritage of Damavand, in this paper
through “base plan methodology” a strategy of urban planning
toward tourism development is prepared in order to make tourism
development as a support for cultural heritage of this city.
Abstract: Background: Maintaining the correct body balance is
essential in the prevention of falls in the elderly, which is especially
important for women because of postmenopausal osteoporosis and
the serious consequences of falls. One of the exercise methods which
is very popular among adults, and which may affect body balance in
the positive way is the Pilates method. The aim of the study was to
evaluate the effect of regular Pilates exercises on the ability to
maintain body balance in static conditions in adult healthy women.
Material and methods: The study group consisted of 20 healthy
women attending Pilates twice a week for at least 1 year. The control
group consisted of 20 healthy women physically inactive. Women in
the age range from 35 to 50 years old without pain in musculoskeletal
system or other pain were only qualified to the groups. Body balance
was assessed using MatScan VersaTek platform with Sway Analysis
Module based on Matscan Clinical 6.7 software (Tekscan Inc.,
U.S.A). The balance was evaluated under the following conditions:
standing on both feet with eyes open, standing on both feet with eyes
closed, one-leg standing (separately on the right and left foot) with
eyes open. Each test lasted 30 seconds. The following parameters
were calculated: estimated size of the ellipse of 95% confidence, the
distance covered by the Center of Gravity (COG), the size of the
maximum shift in the sagittal and frontal planes and load distribution
between the left and right foot, as well as between rear- and forefoot.
Results: It was found that there is significant difference between the
groups in favor of the study group in the size of the confidence
ellipse and maximum shifts of COG in the sagittal plane during
standing on both feet, both with the eyes open and closed (p
Abstract: Introduction: Whole-Body Vibration (WBV) uses
high frequency mechanical stimuli generated by a vibration plate and
transmitted through bone, muscle and connective tissues to the whole
body. Research has shown that long-term vibration-plate training
improves neuromuscular facilitation, especially in afferent neural
pathways, responsible for the conduction of vibration and
proprioceptive stimuli, muscle function, balance and proprioception.
Some researchers suggest that the vibration stimulus briefly inhibits
the conduction of afferent signals from proprioceptors and can
interfere with the maintenance of body balance. The aim of this study
was to evaluate the influence of a single set of exercises associated
with whole-body vibration on the joint position sense and body
balance. Material and methods: The study enrolled 55 people aged
19-24 years. These individuals were randomly divided into a test
group (30 persons) and a control group (25 persons). Both groups
performed the same set of exercises on a vibration plate. The
following vibration parameters: frequency of 20Hz and amplitude of
3mm, were used in the test group. The control group performed
exercises on the vibration plate while it was off. All participants were
instructed to perform six dynamic exercises lasting 30 seconds each
with a 60-second period of rest between them. The exercises involved
large muscle groups of the trunk, pelvis and lower limbs.
Measurements were carried out before and immediately after
exercise. Joint position sense (JPS) was measured in the knee joint
for the starting position at 45° in an open kinematic chain. JPS error
was measured using a digital inclinometer. Balance was assessed in a
standing position with both feet on the ground with the eyes open and
closed (each test lasting 30 sec). Balance was assessed using Matscan
with FootMat 7.0 SAM software. The surface of the ellipse of
confidence and front-back as well as right-left swing were measured
to assess balance. Statistical analysis was performed using Statistica
10.0 PL software. Results: There were no significant differences
between the groups, both before and after the exercise (p> 0.05). JPS
did not change in both the test (10.7° vs. 8.4°) and control groups
(9.0° vs. 8.4°). No significant differences were shown in any of the
test parameters during balance tests with the eyes open or closed in
both the test and control groups (p> 0.05). Conclusions: 1.
Deterioration in proprioception or balance was not observed
immediately after the vibration stimulus. This suggests that vibrationinduced
blockage of proprioceptive stimuli conduction can have only
a short-lasting effect that occurs only as long as a vibration stimulus
is present. 2. Short-term use of vibration in treatment does not impair
proprioception and seems to be safe for patients with proprioceptive
impairment. 3. These results need to be supplemented with an
assessment of proprioception during the application of vibration
stimuli. Additionally, the impact of vibration parameters used in the
exercises should be evaluated.
Abstract: The purposes of hydraulic gate are to maintain the
functions of storing and draining water. It bears long-term hydraulic
pressure and earthquake force and is very important for reservoir and
waterpower plant. The high tensile strength of steel plate is used as
constructional material of hydraulic gate. The cracks and rusts,
induced by the defects of material, bad construction and seismic
excitation and under water respectively, thus, the mechanics
phenomena of gate with crack are probing into the cause of stress
concentration, induced high crack increase rate, affect the safety and
usage of hydroelectric power plant. Stress distribution analysis is a
very important and essential surveying technique to analyze
bi-material and singular point problems. The finite difference
infinitely small element method has been demonstrated, suitable for
analyzing the buckling phenomena of welding seam and steel plate
with crack. Especially, this method can easily analyze the singularity
of kink crack. Nevertheless, the construction form and deformation
shape of some gates are three-dimensional system. Therefore, the
three-dimensional Digital Image Correlation (DIC) has been
developed and applied to analyze the strain variation of steel plate with
crack at weld joint. The proposed Digital image correlation (DIC)
technique is an only non-contact method for measuring the variation of
test object. According to rapid development of digital camera, the cost
of this digital image correlation technique has been reduced.
Otherwise, this DIC method provides with the advantages of widely
practical application of indoor test and field test without the restriction
on the size of test object. Thus, the research purpose of this research is
to develop and apply this technique to monitor mechanics crack
variations of weld steel hydraulic gate and its conformation under
action of loading. The imagines can be picked from real time
monitoring process to analyze the strain change of each loading stage.
The proposed 3-Dimensional digital image correlation method,
developed in the study, is applied to analyze the post-buckling
phenomenon and buckling tendency of welded steel plate with crack.
Then, the stress intensity of 3-dimensional analysis of different
materials and enhanced materials in steel plate has been analyzed in
this paper. The test results show that this proposed three-dimensional
DIC method can precisely detect the crack variation of welded steel
plate under different loading stages. Especially, this proposed DIC
method can detect and identify the crack position and the other flaws
of the welded steel plate that the traditional test methods hardly detect
these kind phenomena. Therefore, this proposed three-dimensional
DIC method can apply to observe the mechanics phenomena of
composite materials subjected to loading and operating.
Abstract: Botanical gardens are very significant organizations
which protect the environment against the increasing environmental
problems, provide environmental education for people, offer
recreation possibilities, etc. This article describes botanical gardens
and their functions. The most important function of botanical garden
is to provide environmental education for people and improve
environmental awareness. Considering this function, some botanical
gardens were examined and opinions were suggested about the
subject.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: Unemployment among the youth is a significant
problem in South Africa. Large corporations and the public sector
simply cannot create enough jobs. Too many youths in South Africa
currently do not consider entrepreneurship as an option in order to
become independent. Unlike the youth of the Netherlands, South
African youth prefer to find employment in the public or private
sector. The Netherlands has a much lower unemployment rate than
South Africa and the Dutch are generally very entrepreneurial. From
early on, entrepreneurship is considered a desirable career option in
the Netherlands. The purpose of this study was to determine whether
there is a difference in the perceptions of some Dutch and South
African students in terms of unemployment and entrepreneurship.
Questionnaires were distributed to students at the North West
University's Vaal Triangle campus in Vanderbijlpark in Gauteng,
South Africa and the Technical University of Delft in the
Netherlands. A descriptive statistical analysis approach was followed
and the means for the independent questions were calculated. The
results demonstrate that the Dutch students are not as concerned
about unemployment after completion of their studies as this is not as
significant a problem as it is in South Africa. Both groups had
positive responses towards the posed questions, but the South African
group felt more strongly about the issues. Both groups of students felt
that there was a need for more practical entrepreneurship training.
The South African education system should focus on practical
entrepreneurship training from a young age.
Abstract: A retrospective study conducted at Christian Medical
College (CMC) Teaching Hospital, Vellore, India on 14th August
2014 to assess the accuracy of clinically estimated foetal weight upon
labour admission. Estimating foetal weight is a crucial factor in
assessing maternal and foetal complications during and after labour.
Medical notes of ninety-eight postnatal women who fulfilled the
inclusion criteria were studied to evaluate the correlation between
their recorded Estimated Foetal Weight (EFW) on admission and
actual birth weight (ABW) of the newborn after delivery. Data
concerning maternal and foetal demographics was also noted.
Accuracy was determined by absolute percentage error and
proportion of estimates within 10% of ABW. Actual birth weights
ranged from 950-4080g. A strong positive correlation between EFW
and ABW (r=0.904) was noted. Term deliveries (≥40 weeks) in the
normal weight range (2500-4000g) had a 59.5% estimation accuracy
(n=74) compared to pre-term (4000g) were underestimated by 25% (n=3) and low birthweight
(LBW) babies were overestimated by 12.7% (n=9). Registrars who
estimated foetal weight were accurate in babies within normal weight
ranges. However, there needs to be an improvement in predicting
weight of macrosomic and LBW foetuses. We have suggested the use
of an amended version of the Johnson’s formula for the Indian
population for improvement and a need to re-audit once
implemented.
Abstract: The purpose of this paper is to contribute to the
enhancement of a hydroelectric plant protection by coordinating
protection measures / existing security and introducing new measures
under a risk management process. In addition, plan identifies key
critical elements of a hydroelectric plant, from its level vulnerabilities
and threats it is subjected to in order to achieve the necessary
protection measures to reduce the level of risk.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: Excessive fretting wear at the taper-trunnion junction
(trunnionosis) apparently contributes to the high failure rates of hip
implants. Implant wear and corrosion lead to the release of metal
particulate debris and subsequent release of metal ions at the tapertrunnion
surface. This results in a type of metal poisoning referred to
as metallosis. The consequences of metal poisoning include;
osteolysis (bone loss), osteoarthritis (pain), aseptic loosening of the
prosthesis and revision surgery. Follow up after revision surgery,
metal debris particles are commonly found in numerous locations. Background: A stable connection between the femoral ball head
(taper) and stem (trunnion) is necessary to prevent relative motions
and corrosion at the taper junction. Hence, the importance of
component assembly cannot be over-emphasized. Therefore, the aim
of this study is to determine the influence of head-stem junction
assembly by press fitting and the subsequent
disengagement/disassembly on the connection strength between the
taper ball head and stem. Methods: CoCr femoral heads were assembled with High stainless
hydrogen steel stem (trunnion) by Push-in i.e. press fit; and
disengaged by pull-out test. The strength and stability of the two
connections were evaluated by measuring the head pull-out forces
according to ISO 7206-10 standards. Findings: The head-stem junction strength linearly increases with
assembly forces.
Abstract: Polycyclic Aromatic Hydrocarbons (PAHs) are
formed mainly because of incomplete combustion of organic
materials during industrial, domestic activities or natural occurrence.
Their toxicity and contamination of terrestrial and aquatic ecosystem
have been established. However, with limited validity index, previous
research has focused on PAHs isomer pair ratios of variable
physicochemical properties in source identification. The objective of
this investigation was to determine the empirical validity of Pearson
Correlation Coefficient (PCC) and Cluster Analysis (CA) in PAHs
source identification along soil samples of different land uses.
Therefore, 16 PAHs grouped, as Endocrine Disruption Substances
(EDSs) were determined in 10 sample stations in top and sub soils
seasonally. PAHs was determined the use of Varian 300 gas
chromatograph interfaced with flame ionization detector. Instruments
and reagents used are of standard and chromatographic grades
respectively. PCC and CA results showed that the classification of
PAHs along pyrolitic and petrogenic organics used in source
signature is about the predominance PAHs in environmental matrix.
Therefore, the distribution of PAHs in the studied stations revealed
the presence of trace quantities of the vast majority of the sixteen
PAHs, which may ultimately inhabit the actual source signature
authentication. Therefore, factors to be considered when evaluating
possible sources of PAHs could be; type and extent of bacterial
metabolism, transformation products/substrates, and environmental
factors such as salinity, pH, oxygen concentration, nutrients, light
intensity, temperature, co-substrates, and environmental medium are
hereby recommended as factors to be considered when evaluating
possible sources of PAHs.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: In this study, the three-dimensional cavitating
turbulent flow in a complete Francis turbine is simulated using
mixture model for cavity/liquid two-phase flows. Numerical analysis
is carried out using ANSYS CFX software release 12, and standard k-ε
turbulence model is adopted for this analysis. The computational
fluid domain consist of spiral casing, stay vanes, guide vanes, runner
and draft tube. The computational domain is discretized with a threedimensional
mesh system of unstructured tetrahedron mesh. The
finite volume method (FVM) is used to solve the governing equations
of the mixture model. Results of cavitation on the runner’s blades
under three different boundary conditions are presented and
discussed. From the numerical results it has been found that the
numerical method was successfully applied to simulate the cavitating
two-phase turbulent flow through a Francis turbine, and also
cavitation is clearly predicted in the form of water vapor formation
inside the turbine. By comparison the numerical prediction results
with a real runner; it’s shown that the region of higher volume
fraction obtained by simulation is consistent with the region of runner
cavitation damage.