Abstract: Increase in using internet makes some problems that
one of them is "internet anxiety". Internet anxiety is a type of anxious
that people may feel during surfing internet or using internet for their
educational purpose, blogging or streaming to digital libraries. The
goal of this study is evaluating of internet anxiety among the
management students. In this research Ealy's internet anxiety
questionnaire, consists of positive and negative items, is completed
by 310 participants. According to the findings, about 64.7% of them
were equal or below to mean anxiety score (50). The distribution of
internet anxiety scores was normal and there was no meaningful
difference between men-s and women's anxiety level in this sample.
Results also showed that there is no meaningful difference of internet
anxiety level between different fields of study in Management. This
evaluation will help managers to perform gap analysis between the
existent level and the desired one. Future work would be providing
techniques for abating human anxiety while using internet via human
computer interaction techniques.
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.
Abstract: Today modern simulations solutions in the wind turbine industry have achieved a high degree of complexity and detail in result. Limitations exist when it is time to validate model results against measurements. Regarding Model validation it is of special interest to identify mode frequencies and to differentiate them from the different excitations. A wind turbine is a complex device and measurements regarding any part of the assembly show a lot of noise. Input excitations are difficult or even impossible to measure due to the stochastic nature of the environment. Traditional techniques for frequency analysis or features extraction are widely used to analyze wind turbine sensor signals, but have several limitations specially attending to non stationary signals (Events). A new technique based on autoregresive analysis techniques is introduced here for a specific application, a comparison and examples related to different events in the wind turbine operations are presented.
Abstract: The purpose of this paper is to provide an overview on methodological aspects of the information technology outsourcing (ITO) surveys, in an attempt to improve the data quality and reporting in survey research. It is based on a review of thirty articles on ITO surveys and focuses on two commonly explored dimensions of ITO, namely what are outsourced and why should there be ITO. This study highlights weaknesses in ITO surveys including lack of a clear definition of population, lack of information regarding the sampling method used, not citing the response rate, no information pertaining to pilot testing of survey instrument and absence of information on internal validity in the use or reporting of surveys. This study represents an attempt with a limited scope to point to shortfalls in the use survey methodology in ITO, and thus raise awareness among researchers in enhancing the reliability of survey findings.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: In this paper we use quintic non-polynomial
spline functions to develop numerical methods for approximation
to the solution of a system of fourth-order boundaryvalue
problems associated with obstacle, unilateral and contact
problems. The convergence analysis of the methods has been
discussed and shown that the given approximations are better
than collocation and finite difference methods. Numerical
examples are presented to illustrate the applications of these
methods, and to compare the computed results with other
known methods.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: One of the vital developmental tasks that an
individual faces during adolescence is choosing a career. Arriving at
a career decision is difficult and anxious for many adolescents in the
tertiary level. The main purpose of this study is to determine the
factors relating to career indecision among freshmen college students
as basis for the formulation of a comprehensive career counseling
program for the psychological well-being of freshmen university
students. The subjects were purposively selected. The Slovin-s
formula was used in determining the sample size, using a 0.05
margin of error in getting the total number of samples per college and
per major. The researcher made use of descriptive correlational study
in determining significant factors relating to career indecision.
Multiple Regression Analysis indicated that career thoughts, career
decisions and vocational identity as factors related to career
indecision.
Abstract: Natural gas is the most popular fossil fuel in the
current era and future as well. Natural gas is existed in underground
reservoirs so it may contain many of non-hydrocarbon components
for instance, hydrogen sulfide, nitrogen and water vapor. These
impurities are undesirable compounds and cause several technical
problems for example, corrosion and environment pollution.
Therefore, these impurities should be reduce or removed from natural
gas stream. Khurmala dome is located in southwest Erbil-Kurdistan
region. The Kurdistan region government has paid great attention for
this dome to provide the fuel for Kurdistan region. However, the
Khurmala associated natural gas is currently flaring at the field.
Moreover, nowadays there is a plan to recover and trade this gas and
to use it either as feedstock to power station or to sell it in global
market. However, the laboratory analysis has showed that the
Khurmala sour gas has huge quantities of H2S about (5.3%) and CO2
about (4.4%). Indeed, Khurmala gas sweetening process has been
removed in previous study by using Aspen HYSYS. However,
Khurmala sweet gas still contents some quintets of water about 23
ppm in sweet gas stream. This amount of water should be removed or
reduced. Indeed, water content in natural gas cause several technical
problems such as hydrates and corrosion. Therefore, this study aims
to simulate the prospective Khurmala gas dehydration process by
using Aspen HYSYS V. 7.3 program. Moreover, the simulation
process succeeded in reducing the water content to less than 0.1ppm.
In addition, the simulation work is also achieved process
optimization by using several desiccant types for example, TEG and
DEG and it also study the relationship between absorbents type and
its circulation rate with HCs losses from glycol regenerator tower.
Abstract: The paper provides the basic overview of simulation optimization. The procedure of its practical using is demonstrated on the real example in simulator Witness. The simulation optimization is presented as a good tool for solving many problems in real praxis especially in production systems. The authors also characterize their own experiences and they mention the strengths and weakness of simulation optimization.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: In this paper, we provide complete end-to-end delay analyses including the relay nodes for instant messages. Message Session Relay Protocol (MSRP) is used to provide congestion control for large messages in the Instant Messaging (IM) service. Large messages are broken into several chunks. These chunks may traverse through a maximum number of two relay nodes before reaching destination according to the IETF specification of the MSRP relay extensions. We discuss the current solutions of sending large instant messages and introduce a proposal to reduce message flows in the IM service. We consider virtual traffic parameter i.e., the relay nodes are stateless non-blocking for scalability purpose. This type of relay node is also assumed to have input rate at constant bit rate. We provide a new scheduling policy that schedules chunks according to their previous node?s delivery time stamp tags. Validation and analysis is shown for such scheduling policy. The performance analysis with the model introduced in this paper is simple and straight forward, which lead to reduced message flows in the IM service.
Abstract: The purpose of this study was to investigate effects of
modality and redundancy principles on music theory learning among
pupils of different anxiety levels. The lesson of music theory was
developed in three different modes, audio and image (AI), text with
image (TI) and audio with image and text (AIT). The independent
variables were the three modes of courseware. The moderator
variable was the anxiety level, while the dependent variable was the
post test score. The study sample consisted of 405 third-grade pupils.
Descriptive and inferential statistics were conducted to analyze the
collected data. Analyses of covariance (ANCOVA) and Post hoc
were carried out to examine the main effects as well as the
interaction effects of the independent variables on the dependent
variable. The findings of this study showed that medium anxiety
pupils performed significantly better than low and high anxiety
pupils in all the three treatment modes. The AI mode was found to
help pupils with high anxiety significantly more than the TI and AIT
modes.
Abstract: This paper presents a method for determining the
uniaxial tensile properties such as Young-s modulus, yield strength
and the flow behaviour of a material in a virtually non-destructive
manner. To achieve this, a new dumb-bell shaped miniature
specimen has been designed. This helps in avoiding the removal of
large size material samples from the in-service component for the
evaluation of current material properties. The proposed miniature
specimen has an advantage in finite element modelling with respect
to computational time and memory space. Test fixtures have been
developed to enable the tension tests on the miniature specimen in a
testing machine. The studies have been conducted in a chromium
(H11) steel and an aluminum alloy (AR66). The output from the
miniature test viz. load-elongation diagram is obtained and the finite
element simulation of the test is carried out using a 2D plane stress
analysis. The results are compared with the experimental results. It is
observed that the results from the finite element simulation
corroborate well with the miniature test results. The approach seems
to have potential to predict the mechanical properties of the
materials, which could be used in remaining life estimation of the
various in-service structures.
Abstract: This paper explores the knowledge and attitude of
women and men in decision making on pap smear screening. This
qualitative study recruited 52 respondents with 44 women and 8 men,
using the purposive sampling with snowballing technique through indepth
interviews. This study demonstrates several key findings:
Female respondents have better knowledge compared to male. Most
of the women perceived that pap smear screening is beneficial and
important, but to proceed with the test is still doubtful. Male
respondents were supportive in terms of sending their spouses to the
health facilities or give more freedom to their wives to choose and
making decision on their own health due to prominent reason that
women know best on their own health. It is expected that the results
from this study will provide useful guideline for healthcare providers
to prepare any action/intervention to provide an extensive education
to improve people-s knowledge and attitude towards pap smear.
Abstract: In this study, the contact problem of a layered composite which consists of two materials with different elastic constants and heights resting on two rigid flat supports with sharp edges is considered. The effect of gravity is neglected. While friction between the layers is taken into account, it is assumed that there is no friction between the supports and the layered composite so that only compressive tractions can be transmitted across the interface. The layered composite is subjected to a uniform clamping pressure over a finite portion of its top surface. The problem is reduced to a singular integral equation in which the contact pressure is the unknown function. The singular integral equation is evaluated numerically and the results for various dimensionless quantities are presented in graphical forms.
Abstract: In this paper we illuminate a frequency domain based
classification method for video scenes. Videos from certain topical
areas often contain activities with repeating movements. Sports
videos, home improvement videos, or videos showing mechanical
motion are some example areas. Assessing main and side frequencies
of each repeating movement gives rise to the motion type. We
obtain the frequency domain by transforming spatio-temporal motion
trajectories. Further on we explain how to compute frequency features
for video clips and how to use them for classifying. The focus of
the experimental phase is on transforms utilized for our system.
By comparing various transforms, experiments show the optimal
transform for a motion frequency based approach.
Abstract: Positron emission particle tracking (PEPT) is a
technique in which a single radioactive tracer particle can be
accurately tracked as it moves. A limitation of PET is that in order to
reconstruct a tomographic image it is necessary to acquire a large
volume of data (millions of events), so it is difficult to study rapidly
changing systems. By considering this fact, PEPT is a very fast
process compared with PET.
In PEPT detecting both photons defines a line and the annihilation
is assumed to have occurred somewhere along this line. The location
of the tracer can be determined to within a few mm from coincident
detection of a small number of pairs of back-to-back gamma rays and
using triangulation. This can be achieved many times per second and
the track of a moving particle can be reliably followed. This
technique was invented at the University of Birmingham [1].
The attempt in PEPT is not to form an image of the tracer particle
but simply to determine its location with time. If this tracer is
followed for a long enough period within a closed, circulating system
it explores all possible types of motion.
The application of PEPT to industrial process systems carried out
at the University of Birmingham is categorized in two subjects: the
behaviour of granular materials and viscous fluids. Granular
materials are processed in industry for example in the manufacture of
pharmaceuticals, ceramics, food, polymers and PEPT has been used
in a number of ways to study the behaviour of these systems [2].
PEPT allows the possibility of tracking a single particle within the
bed [3]. Also PEPT has been used for studying systems such as: fluid
flow, viscous fluids in mixers [4], using a neutrally-buoyant tracer
particle [5].
Abstract: This article describes design of the 8-bit asynchronous
microcontroller simulation model in VHDL. The model is created in
ISE Foundation design tool and simulated in Modelsim tool. This
model is a simple application example of asynchronous systems
designed in synchronous design tools. The design process of creating
asynchronous system with 4-phase bundled-data protocol and with
matching delays is described in the article. The model is described in
gate-level abstraction.
The simulation waveform of the functional construction is the
result of this article. Described construction covers only the
simulation model. The next step would be creating synthesizable
model to FPGA.
Abstract: The problem of Small Area Estimation (SAE) is complex because of various information sources and insufficient data. In this paper, an approach for SAE is presented for decision-making at national, regional and local level. We propose an Empirical Best Linear Unbiased Predictor (EBLUP) as an estimator in order to combine several information sources to evaluate various indicators. First, we present the urban audit project and its environmental, social and economic indicators. Secondly, we propose an approach for decision making in order to estimate indicators. An application is used to validate the theoretical proposal. Finally, a decision support system is presented based on open-source environment.