Abstract: Mass flow measurement is the basis of most technoeconomic
formulations in the chemical industry. This calls for
reliable and accurate detection of mass flow. Flow measurement
laboratory experiments were conducted using various instruments.
These consisted of orifice plates, various sized rotameters, wet gas
meter and soap bubble meter. This work was aimed at evaluating
appropriate operating conditions and accuracy of the aforementioned
devices. The experimental data collected were compared to
theoretical predictions from Bernoulli’s equation and calibration
curves supplied by the instrument’s manufacturers. The results
obtained showed that rotameters were more reliable for measuring
high and low flow rates; while soap-bubble meters and wet-gas
meters were found to be suitable for measuring low flow rates. The
laboratory procedures and findings of the actual work can assist
engineering students and professionals in conducting their flow
measurement laboratory test work.
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.
Abstract: This entry concerned with dense silica bricks
microstructure was produced as a part of a project within the
Technology Agency of the Czech Republic which is being
implemented in cooperation of the biggest producer of refractories
the P-D Refractories CZ company with the research organisation
Brno University of Technology. The paper is focused on the
influence of mixture homogenisation and the influence of grain size
of the mineraliser on the resulting utility properties of the material as
well as its microstructure. It has a decisive influence on the durability
of the material in a building structure. This paper is a continuation of
a previously published study dealing with the suitability of various
types of mineralising agents in terms of density, strength and mineral
composition of silica brick.
The entry describes the influence of the method of mixture
homogenisation and the influence of granulometry of the applied Femineralising
agent on the resulting silica microstructure. Porosity,
density, phase composition and microstructure of the experimentally
prepared silica bricks samples were examined and the results were
discussed in context with the technology of homogenisation and
firing temperature used. The properties of silica bricks samples were
compared to the sample without any Fe-mineraliser.
Abstract: Load carrying capacity of an oil lubricated two-axial
groove journal bearing is simulated by taking into account the
viscosity variations in lubricant due to the addition of TiO2
nanoparticles as lubricant additive. Shear viscosities of TiO2
nanoparticle dispersions in oil are measured for various nanoparticle
additive concentrations. The viscosity model derived from the
experimental viscosities is employed in a modified Reynolds
equation to obtain the pressure profiles and load carrying capacity of
two-axial groove journal bearing. Results reveal an increase in load
carrying capacity of bearings operating on nanoparticle dispersions as
compared to plain oil.
Abstract: This study focuses on the cooling of a photovoltaic
panel (PV). Indeed, the cooling improves the conversion capacity of
this one and maintains, under extreme conditions of air temperature,
the panel temperature at an appreciable level which avoids the
altering. To do this, a fan provides forced circulation of air. Because
the fan is supplied by the panel, it is necessary to determine the
optimum operating point that unites efficiency of the PV with the
consumption of the fan. For this matter, numerical simulations are
performed at varying mass flow rates of air, under two extreme air
temperatures (50°C, 25°C) and a fixed solar radiation (1000W.m2) in
a case of no wind.
Abstract: The study deals with the challenges in developing a
test rig to test the performance of water lubricated journal bearing.
The test rig is designed to simulate the working conditions of the
bearing in order to understand their performance before they are put
in operation. The bearing that is studied is the commercially available
water lubricated bearing which has a rubber liner bonded with a rigid
metal shell. The lubricant enters the bearing axially through a
pressurized inlet tank and exits to an outlet tank which is at
sufficiently low pressure. The load on the bearing is applied through
the dead weight system which acts both in upward and downward
direction so that net load acts on the bearing. The issues in feeding
the lubricant into the bearing from the inlet side and preventing the
leakage of the lubricant is discussed. The application of the load on
the test bearing while maintaining the bearing afloat is also discussed.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: Access control is one of the most challenging issues
facing information security. Access control is defined as, the ability to
permit or deny access to a particular computational resource or digital
information by an unauthorized user or subject. The concept of usage
control (UCON) has been introduced as a unified approach to capture a
number of extensions for access control models and systems. In
UCON, an access decision is determined by three factors:
authorizations, obligations and conditions. Attribute mutability and
decision continuity are two distinct characteristics introduced by
UCON for the first time. An observation of UCON components
indicates that, the components are predefined and static. In this paper,
we propose a new and flexible model of usage control for the creation
and elimination of some of these components; for example new
objects, subjects, attributes and integrate these with the original
UCON model. We also propose a model for concurrent usage
scenarios in UCON.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: The use of permanent magnets (PM) is increasing in
permanent magnet synchronous machines (PMSM) to fulfill the
requirements of high efficiency machines in modern industry. PMSM
are widely used in industrial applications, wind power plants and the
automotive industry. Since PMSM are used in different
environmental conditions, the long-term effect of NdFeB-based
magnets at high temperatures and their corrosion behavior have to be
studied due to the irreversible loss of magnetic properties.
In this paper, the effect of magnetic properties due to corrosion
and increasing temperature in a climatic chamber has been presented.
The magnetic moment and magnetic field of the magnets were
studied experimentally.
Abstract: In this study, the evaluation of thermal stability of the
micrometer-sized silica particle reinforced epoxy composite was
carried out through the measurement of thermal expansion coefficient
and Young’s modulus of the specimens. For all the specimens in this
study from the baseline to those containing 50 wt% silica filler, the
thermal expansion coefficients and the Young’s moduli were
gradually decreased down to 20% and increased up to 41%,
respectively. The experimental results were compared with fillervolume-
based simple empirical relations. The experimental results of
thermal expansion coefficients correspond with those of Thomas’s
model which is modified from the rule of mixture. However, the
measured result for Young’s modulus tends to be increased slightly.
The differences in increments of the moduli between experimental and
numerical model data are quite large.
Abstract: In this research work, neural networks were applied to
classify two types of hip joint implants based on the relative hip joint
implant side speed and three components of each ground reaction
force. The condition of walking gait at normal velocity was used and
carried out with each of the two hip joint implants assessed. Ground
reaction forces’ kinetic temporal changes were considered in the first
approach followed but discarded in the second one. Ground reaction
force components were obtained from eighteen patients under such
gait condition, half of which had a hip implant type I-II, whilst the
other half had the hip implant, defined as type III by Orthoload®.
After pre-processing raw gait kinetic data and selecting the time
frames needed for the analysis, the ground reaction force components
were used to train a MLP neural network, which learnt to distinguish
the two hip joint implants in the abovementioned condition. Further
to training, unknown hip implant side and ground reaction force
components were presented to the neural networks, which assigned
those features into the right class with a reasonably high accuracy for
the hip implant type I-II and the type III. The results suggest that
neural networks could be successfully applied in the performance
assessment of hip joint implants.
Abstract: Audio-lingual Method (ALM) is a teaching approach
that is claimed that ineffective for teaching second/foreign languages.
Because some linguists and second/foreign language teachers believe
that ALM is a rote learning style. However, this study is done on a
belief that ALM will be able to solve Thais’ English speaking
problem. This paper aims to report the findings on teaching English
speaking to adult learners with an “adapted ALM”, one distinction of
which is to use Thai as the medium language of instruction.
The participants are consisted of 9 adult learners. They were
allowed to speak English more freely using both the materials
presented in the class and their background knowledge of English. At
the end of the course, they spoke English more fluently, more
confidently, to the extent that they applied what they learnt both in
and outside the class.
Abstract: Over the past era, there have been a lot of efforts and
studies are carried out in growing proficient tools for performing
various tasks in big data. Recently big data have gotten a lot of
publicity for their good reasons. Due to the large and complex
collection of datasets it is difficult to process on traditional data
processing applications. This concern turns to be further mandatory
for producing various tools in big data. Moreover, the main aim of
big data analytics is to utilize the advanced analytic techniques
besides very huge, different datasets which contain diverse sizes from
terabytes to zettabytes and diverse types such as structured or
unstructured and batch or streaming. Big data is useful for data sets
where their size or type is away from the capability of traditional
relational databases for capturing, managing and processing the data
with low-latency. Thus the out coming challenges tend to the
occurrence of powerful big data tools. In this survey, a various
collection of big data tools are illustrated and also compared with the
salient features.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: Estimation of a proportion has many applications in
economics and social studies. A common application is the estimation
of the low income proportion, which gives the proportion of people
classified as poor into a population. In this paper, we present this
poverty indicator and propose to use the logistic regression estimator
for the problem of estimating the low income proportion. Various
sampling designs are presented. Assuming a real data set obtained
from the European Survey on Income and Living Conditions, Monte
Carlo simulation studies are carried out to analyze the empirical
performance of the logistic regression estimator under the various
sampling designs considered in this paper. Results derived from
Monte Carlo simulation studies indicate that the logistic regression
estimator can be more accurate than the customary estimator under
the various sampling designs considered in this paper. The stratified
sampling design can also provide more accurate results.
Abstract: The study area is Zaria, located in the basement
complex of northern Nigeria. The rock type forming the major part of
the Zaria batholith is granite. This research work was carried out to
compare the responses of seismic refraction tomography and
resistivity tomography in the same geologic environment and under
the same conditions. Hence, the choice of the site that has a visible
granitic outcrop that extends across a narrow stream channel and is
flanked by unconsolidated overburden, a neutral profile that was
covered by plain overburden and a site with thick lateritic cover
became necessary. The results of the seismic and resistivity
tomography models reveals that seismic velocity and resistivity does
not always simultaneously increase with depth, but their responses in
any geologic environment are determined by changes in the
mechanical and chemical content of the rock types rather than depth.
Abstract: The measured data obtained from sensors in
continuous monitoring of civil structures are mainly used for modal
identification and damage detection. Therefore, when modal
identification analysis is carried out the quality in the identification of
the modes will highly influence the damage detection results. It is
also widely recognized that the usefulness of the measured data used
for modal identification and damage detection is significantly
influenced by the number and locations of sensors. The objective of
this study is the numerical implementation of two widely known
optimum sensor placement methods in beam-like structures.