Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: The problem of FIR system parameter estimation has been considered in the paper. A new robust recursive algorithm for simultaneously estimation of parameters and scale factor of prediction residuals in non-stationary environment corrupted by impulsive noise has been proposed. The performance of derived algorithm has been tested by simulations.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: In this paper, a benchmarking framework is presented
for the performance assessment of irrigations systems. Firstly, a data
envelopment analysis (DEA) is applied to measure the technical
efficiency of irrigation systems. This method, based on linear
programming, aims to determine a consistent efficiency ranking of
irrigation systems in which known inputs, such as water volume
supplied and total irrigated area, and a given output corresponding to
the total value of irrigation production are taken into account
simultaneously. Secondly, in order to examine the irrigation
efficiency in more detail, a cross – system comparison is elaborated
using a performance indicators set selected by IWMI. The above
methodologies were applied in Thessaloniki plain, located in
Northern Greece while the results of the application are presented and
discussed. The conjunctive use of DEA and performance indicators
seems to be a very useful tool for efficiency assessment and
identification of best practices in irrigation systems management.
Abstract: Decision fusion is one of hot research topics in
classification area, which aims to achieve the best possible
performance for the task at hand. In this paper, we
investigate the usefulness of this concept to improve change
detection accuracy in remote sensing. Thereby, outputs of
two fuzzy change detectors based respectively on
simultaneous and comparative analysis of multitemporal
data are fused by using fuzzy integral operators. This
method fuses the objective evidences produced by the
change detectors with respect to fuzzy measures that express
the difference of performance between them. The proposed
fusion framework is evaluated in comparison with some
ordinary fuzzy aggregation operators. Experiments carried
out on two SPOT images showed that the fuzzy integral was
the best performing. It improves the change detection
accuracy while attempting to equalize the accuracy rate in
both change and no change classes.
Abstract: This paper implements the inventory model developed in the first part of this paper in a simplified problem to simultaneously reduce costs and risks in JIT systems. This model is developed to ascertain an optimal ordering strategy for procuring raw materials by using regular multi-external and local backup suppliers to reduce the total cost of the products, and at the same time to reduce the risks arising from this cost reduction within production systems. A comparison between the cost of using the JIT system and using the proposed inventory model shows the superiority of the use of the inventory model.
Abstract: Recently, in some places, optical-fibre access
networks have been used with GPON technology belonging to
organizations (in most cases public bodies) that act as neutral
operators. These operators simultaneously provide network services
to various telecommunications operators that offer integrated voice,
data and television services. This situation creates new problems
related to quality of service, since the interests of the users are
intermingled with the interests of the operators. In this paper, we
analyse this problem and consider solutions that make it possible to
provide guaranteed quality of service for voice over IP, data services
and interactive digital television.
Abstract: PCCI engines can reduce NOx and PM emissions
simultaneously without sacrificing thermal efficiency, but a low
combustion temperature resulting from early fuel injection, and
ignition occurring prior to TDC, can cause higher THC and CO
emissions and fuel consumption. In conclusion, it was found that the
PCCI combustion achieved by the 2-stage injection strategy with
optimized calibration factors (e.g. EGR rate, injection pressure, swirl
ratio, intake pressure, injection timing) can reduce NOx and PM
emissions simultaneously. This research works are expected to
provide valuable information conducive to a development of an
innovative combustion engine that can fulfill upcoming stringent
emission standards.
Abstract: The spatial variation in plant species associated with intercropping is intended to reduce resource competition between species and increase yield potential. A field experiment was carried out on corn (Zea mays L.) and soybean (Glycine max L.) intercropping in a replacement series experiment with weed contamination consist of: weed free, infestation of redroot pigweed, infestation of jimsonweed and simultaneous infestation of redroot pigweed and jimsonweed in Karaj, Iran during 2007 growing season. The experimental design was a randomized complete block in factorial experiment with replicated thrice. Significant (P≤0.05) differences were observed in yield in intercropping. Corn yield was higher in intercropping, but soybean yield was significantly reduced by corn when intercropped. However, total productivity and land use efficiency were high under the intercropping system even in contamination of either species of weeds. Aggressivity of corn relative to soybean revealed the greater competitive ability of corn than soybean. Land equivalent ratio (LER) more than 1 in all treatments attributed to intercropping advantages and was highest in 50: 50 (corn/soybean) in weed free. These findings suggest that intercropping corn and soybean increase total productivity per unit area and improve land use efficiency. Considering the experimental findings, corn-soybean intercropping (50:50) may be recommended for yield advantage, more efficient utilization of resources, and weed suppression as a biological control.
Abstract: The aim of this paper is to adopt a compromise ratio (CR) methodology for fuzzy multi-attribute single-expert decision making proble. In this paper, the rating of each alternative has been described by linguistic terms, which can be expressed as triangular fuzzy numbers. The compromise ratio method for fuzzy multi-attribute single expert decision making has been considered here by taking the ranking index based on the concept that the chosen alternative should be as close as possible to the ideal solution and as far away as possible from the negative-ideal solution simultaneously. From logical point of view, the distance between two triangular fuzzy numbers also is a fuzzy number, not a crisp value. Therefore a fuzzy distance measure, which is itself a fuzzy number, has been used here to calculate the difference between two triangular fuzzy numbers. Now in this paper, with the help of this fuzzy distance measure, it has been shown that the compromise ratio is a fuzzy number and this eases the problem of the decision maker to take the decision. The computation principle and the procedure of the compromise ratio method have been described in detail in this paper. A comparative analysis of the compromise ratio method previously proposed [1] and the newly adopted method have been illustrated with two numerical examples.
Abstract: Solid fuel transient burning behavior under oxidizer
gas flow is numerically investigated. It is done using analysis of the
regression rate responses to the imposed sudden and oscillatory
variation at inflow properties. The conjugate problem is considered
by simultaneous solution of flow and solid phase governing
equations to compute the fuel regression rate. The advection
upstream splitting method is used as flow computational scheme in
finite volume method. The ignition phase is completely simulated to
obtain the exact initial condition for response analysis. The results
show that the transient burning effects which lead to the combustion
instabilities and intermittent extinctions could be observed in solid
fuels as the solid propellants.
Abstract: In this study, a synthetic pathway was created by
assembling genes from Clostridium butyricum and Escherichia coli
in different combinations. Among the genes were dhaB1 and dhaB2
from C. butyricum VPI1718 coding for glycerol dehydratase (GDHt)
and its activator (GDHtAc), respectively, involved in the conversion
of glycerol to 3-hydroxypropionaldehyde (3-HPA). The yqhD gene
from E.coli BL21 was also included which codes for an NADPHdependent
1,3-propanediol oxidoreductase isoenzyme (PDORI)
reducing 3-HPA to 1,3-propanediol (1,3-PD). Molecular modeling
analysis indicated that the conformation of fusion protein of YQHD
and DHAB1 was favorable for direct molecular channeling of the
intermediate 3-HPA. According to the simulation results, the yqhD
and dhaB1 gene were assembled in the upstream of dhaB2 to express
a fusion protein, yielding the recombinant strain E. coliBL21
(DE3)//pET22b+::yqhD-dhaB1_dhaB2 (strain BP41Y3). Strain
BP41Y3 gave 10-fold higher 1,3-PD concentration than E. coliBL21
(DE3)//pET22b+::yqhD-dhaB1_dhaB2 (strain BP31Y2) expressing
the recombinant enzymes simultaneously but in a non-fusion mode.
This is the first report using a gene fusion approach to enhance the
biological conversion of glycerol to the value added compound 1,3-
PD.
Abstract: Traffic Engineering (TE) is the process of controlling
how traffic flows through a network in order to facilitate efficient and
reliable network operations while simultaneously optimizing network
resource utilization and traffic performance. TE improves the
management of data traffic within a network and provides the better
utilization of network resources. Many research works considers intra
and inter Traffic Engineering separately. But in reality one influences
the other. Hence the effective network performances of both inter and
intra Autonomous Systems (AS) are not optimized properly. To
achieve a better Joint Optimization of both Intra and Inter AS TE, we
propose a joint Optimization technique by considering intra-AS
features during inter – AS TE and vice versa. This work considers the
important criterion say latency within an AS and between ASes. and
proposes a Bi-Criteria Latency optimization model. Hence an overall
network performance can be improved by considering this jointoptimization
technique in terms of Latency.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: The selective recovery of heavy metals of Cu, Zn, Ni and Cr from a mixed plating sludge by sulfidation and oxidation treatment was targeted in this study. At first, the mixed plating sludge was simultaneously subjected to an extraction and Cu sulfidation process at pH=1.5 to dissolve heavy metals and to precipitate Cu2+ as CuS. In the next step, the sulfidation treatment of Zn was carried out at pH=4.5 and the residual solution was subjected to an oxidation treatment of chromium with H2O2 at pH=10.0. After the experiments, the selectivity of metal precipitation and the chromium oxidation ratio were evaluated. As results, it was found that the filter cake obtained after selective sulfidation of Cu was composed of 96.6% of Cu (100% equals to the sum of Cu, Zn, Ni and Cr contents). Such findings confirmed that almost complete extraction of heavy metals was achieved at pH=1.5 and also that Cu could be selectively recovered as CuS. Further, the filter cake obtained at pH=4.5 was composed of 91.5% Zn and 6.83% of Cr. Regarding the chromium oxidation step, the chromium oxidation ratio was found to increase with temperature and the addition of oxidation agent of H2O2, but only oxidation ratio of 59% was achieved at a temperature of 60°C and H2O2 to Cr3+ equivalent ratio of 180.
Abstract: It is very important to determine reference temperature when convective temperature because it should be used to calculate the temperature potential. This paper deals with the development of a new method that can determine heat transfer coefficient and reference free stream temperature simultaneously, based on transient heat transfer experiments with using two narrow band thermo-tropic liquid crystals (TLC's). The method is validated through error analysis in terms of the random uncertainties in the measured temperatures. It is shown how the uncertainties in heat transfer coefficient and free stream temperature can be reduced. The general method described in this paper is applicable to many heat transfer models with unknown free stream temperature.
Abstract: Outsourcing, a management practice strongly
consolidated within the area of Information Systems, is currently
going through a stage of unstoppable growth. This paper makes a
proposal about the main reasons which may lead firms to adopt
Information Systems Outsourcing. It will equally analyse the
potential risks that IS clients are likely to face. An additional
objective is to assess these reasons and risks in the case of large
Spanish firms, while simultaneously examining their evolution over
time.
Abstract: In this survey the process of crack propagation at the
toe of concrete gravity dam is investigated by applying principals
and criteria of linear elastic fracture mechanic. Simulating process of
earthquake conditions for three models of dam with different
geometrical condition, in empty reservoir under plain stress is
calculated through special fracture mechanic software FRANNC2D
[1] for determining fracture mechanic criteria. The outcomes showed
that in spite of the primary expectations, the simultaneous existence
of fillet in both toe and heel area (model 3), the rate of maximum
principal stress has not been decreased; however, even the maximum
principal stress has increased, so it caused stress intensity factors
increase which is undesirable. On the other hand, the dam with heel
fillet has shown the best attitude and it is because of items like
decreasing the rates of maximum and minimum principal stresses and
also is related to decreasing the rates of stress intensity factors for 1st
& 2nd modes of the model.
Abstract: In the traditional concept of product life cycle management, the activities of design, manufacturing, and assembly are performed in a sequential way. The drawback is that the considerations in design may contradict the considerations in manufacturing and assembly. The different designs of components can lead to different assembly sequences. Therefore, in some cases, a good design may result in a high cost in the downstream assembly activities. In this research, an integrated design evaluation and assembly sequence planning model is presented. Given a product requirement, there may be several design alternative cases to design the components for the same product. If a different design case is selected, the assembly sequence for constructing the product can be different. In this paper, first, the designed components are represented by using graph based models. The graph based models are transformed to assembly precedence constraints and assembly costs. A particle swarm optimization (PSO) approach is presented by encoding a particle using a position matrix defined by the design cases and the assembly sequences. The PSO algorithm simultaneously performs design evaluation and assembly sequence planning with an objective of minimizing the total assembly costs. As a result, the design cases and the assembly sequences can both be optimized. The main contribution lies in the new concept of integrated design evaluation and assembly sequence planning model and the new PSO solution method. The test results show that the presented method is feasible and efficient for solving the integrated design evaluation and assembly planning problem. In this paper, an example product is tested and illustrated.