Abstract: This paper identifies five key design characteristics of
production scheduling software systems in printed circuit board (PCB) manufacturing. The authors consider that, in addition to an effective scheduling engine, a scheduling system should be able to
process a preventative maintenance calendar, to give the user the
flexibility to handle data using a variety of electronic sources, to run
simulations to support decision-making, and to have simple and
customisable graphical user interfaces. These design considerations
were the result of a review of academic literature, the evaluation of
commercial applications and a compilation of requirements of a PCB manufacturer. It was found that, from those systems that were evaluated, those that effectively addressed all five characteristics
outlined in this paper were the most robust of all and could be used in
PCB manufacturing.
Abstract: This paper undertakes the problem of optimal
capacitor placement in a distribution system. The problem is how to
optimally determine the locations to install capacitors, the types and
sizes of capacitors to he installed and, during each load level,the
control settings of these capacitors in order that a desired objective
function is minimized while the load constraints,network constraints
and operational constraints (e.g. voltage profile) at different load
levels are satisfied. The problem is formulated as a combinatorial
optimization problem with a nondifferentiable objective function.
Four solution mythologies based on algorithms (GA),tabu search
(TS), and hybrid GA-SA algorithms are presented.The solution
methodologies are preceded by a sensitivity analysis to select the
candidate capacitor installation locations.
Abstract: In the present study, position estimation of switched reluctance motor (SRM) has been achieved on the basis of the artificial neural networks (ANNs). The ANNs can estimate the rotor position without using an extra rotor position sensor by measuring the phase flux linkages and phase currents. Flux linkage-phase current-rotor position data set and supervised backpropagation learning algorithm are used in training of the ANN based position estimator. A 4-phase SRM have been used to verify the accuracy and feasibility of the proposed position estimator. Simulation results show that the proposed position estimator gives precise and accurate position estimations for both under the low and high level reference speeds of the SRM
Abstract: We demonstrate through a sample application, Ebanking,
that the Web Service Modelling Language Ontology component
can be used as a very powerful object-oriented database design
language with logic capabilities. Its conceptual syntax allows the
definition of class hierarchies, and logic syntax allows the definition
of constraints in the database. Relations, which are available for
modelling relations of three or more concepts, can be connected to
logical expressions, allowing the implicit specification of database
content. Using a reasoning tool, logic queries can also be made
against the database in simulation mode.
Abstract: The goal of this paper is to find Wardrop equilibrium
in transport networks at case of uncertainty situations, where the
uncertainty comes from lack of information. We use simulation tool
to find the equilibrium, which gives only approximate solution, but
this is sufficient for large networks as well. In order to take the
uncertainty into account we have developed an interval-based
procedure for finding the paths with minimal cost using the
Dempster-Shafer theory. Furthermore we have investigated the users-
behaviors using game theory approach, because their path choices
influence the costs of the other users- paths.
Abstract: Multicarrier code-division multiple-access is one of the
effective techniques to gain its multiple access capability, robustness
against fading, and to mitigate the ISI. In this paper, we propose an
improved mulcarrier CDMA system with adaptive subchannel
allocation. We analyzed the performance of our proposed system in
frequency selective fading environment with narrowband interference
existing and compared it with that of parallel transmission over many
subchannels (namely, conventional MC-CDMA scheme) and
DS-CDMA system. Simulation results show that adaptive subchannel
allocation scheme, when used in conventional multicarrier CDMA
system, the performance will be greatly improved.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: The use of High Order Statistics (HOS) analysis is
expected to provide so many candidates of features that can be selected for pattern recognition. More candidates of the feature can
be extracted using simple manipulation through a specific mathematical function prior to the HOS analysis. Feature extraction
method using HOS analysis combined with Difference to the Nth-Power manipulation has been examined in application for Automatic
Modulation Recognition (AMR) to perform scheme recognition of three digital modulation signal, i.e. QPSK-16QAM-64QAM in the
AWGN transmission channel. The simulation results is reported
when the analysis of HOS up to order-12 and the manipulation of Difference to the Nth-Power up to N = 4. The obtained accuracy rate
of AMR using the method of Simple Decision obtained 90% in SNR > 10 dB in its classifier, while using the method of Voted Decision is
96% in SNR > 2 dB.
Abstract: When studying electronics, hands-on experience is considered to be very valuable for a better understanding of the concepts of electricity and electronics. Students lacking sufficient time in the lab are often put at disadvantage. A way to overcome this, is by using interactive multimedia in a virtual environment. Instead of proposing another new ad-hoc simulator for e-learning, we propose in this paper an e-learning platform integrating the SPICE simulator as a web service. This enables to make use of all the functions of the de-facto standard simulator SPICE inelectronics when developing new simulations.
Abstract: To satisfy the need of outfield tests of star sensors, a
method is put forward to construct the reference attitude benchmark.
Firstly, its basic principle is introduced; Then, all the separate
conversion matrixes are deduced, which include: the conversion
matrix responsible for the transformation from the Earth Centered
Inertial frame i to the Earth-centered Earth-fixed frame w according to
the time of an atomic clock, the conversion matrix from frame w to the
geographic frame t, and the matrix from frame t to the platform frame
p, so the attitude matrix of the benchmark platform relative to the
frame i can be obtained using all the three matrixes as the
multiplicative factors; Next, the attitude matrix of the star sensor
relative to frame i is got when the mounting matrix from frame p to the
star sensor frame s is calibrated, and the reference attitude angles for
star sensor outfield tests can be calculated from the transformation
from frame i to frame s; Finally, the computer program is finished to
solve the reference attitudes, and the error curves are drawn about the
three axis attitude angles whose absolute maximum error is just 0.25ÔÇ│.
The analysis on each loop and the final simulating results manifest that
the method by precise timing to acquire the absolute reference attitude
is feasible for star sensor outfield tests.
Abstract: Nonlinear finite element method with eight noded
isoparametric quadrilateral element is used for prediction of loaddeformation
behavior including bearing capacity of foundations.
Modified generalized plasticity model with non-associated flow rule
is applied for analysis of soil-footing system. Also Von Mises and
Tresca criterions are used for simulation of soil behavior. Modified
generalized plasticity model is able to simulate load-deformation
including softening behavior. Localization phenomena are considered
by different meshes. Localization phenomena have not been seen in
the examples. Predictions by modified generalized plasticity model
show good agreement with laboratory data and theoretical prediction
in comparison the other models.
Abstract: The adsorption of simulated aqueous solution containing textile remazol reactive dye, namely Red 3BS by palm shell activated carbon (PSAC) as adsorbent was carried out using Response Surface Methodology (RSM). A Box-Behnken design in three most important operating variables; initial dye concentration, dosage of adsorbent and speed of impeller was employed for experimental design and optimization of results. The significance of independent variables and their interactions were tested by means of the analysis of variance (ANOVA) with 95% confidence limits. Model indicated that with the increasing of dosage and speed give the result of removal up to 90% with the capacity uptake more than 7 mg/g. High regression coefficient between the variables and the response (R-Sq = 93.9%) showed of good evaluation of experimental data by polynomial regression model.
Abstract: The radiative exchange method is introduced as a
numerical method for the simulation of radiative heat transfer in an
absorbing, emitting and isotropically scattering media. In this
method, the integro-differential radiative balance equation is solved
by using a new introduced concept for the exchange factor. Even
though the radiative source term is calculated in a mesh structure that
is coarser than the structure used in computational fluid dynamics,
calculating the exchange factor between different coarse elements by
using differential integration elements makes the result of the method
close to that of integro-differential radiative equation. A set of
equations for calculating exchange factors in two and threedimensional
Cartesian coordinate system is presented, and the
method is used in the simulation of radiative heat transfer in twodimensional
rectangular case and a three-dimensional simple cube.
The result of using this method in simulating different cases is
verified by comparing them with those of using other numerical
radiative models.
Abstract: In this paper a procedure for the split-pipe design of looped water distribution network based on the use of simulated annealing is proposed. Simulated annealing is a heuristic-based search algorithm, motivated by an analogy of physical annealing in solids. It is capable for solving the combinatorial optimization problem. In contrast to the split-pipe design that is derived from a continuous diameter design that has been implemented in conventional optimization techniques, the split-pipe design proposed in this paper is derived from a discrete diameter design where a set of pipe diameters is chosen directly from a specified set of commercial pipes. The optimality and feasibility of the solutions are found to be guaranteed by using the proposed method. The performance of the proposed procedure is demonstrated through solving the three well-known problems of water distribution network taken from the literature. Simulated annealing provides very promising solutions and the lowest-cost solutions are found for all of these test problems. The results obtained from these applications show that simulated annealing is able to handle a combinatorial optimization problem of the least cost design of water distribution network. The technique can be considered as an alternative tool for similar areas of research. Further applications and improvements of the technique are expected as well.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: State-dependent Riccati equation based controllers are
becoming increasingly popular because of having attractive
properties like optimality, stability and robustness. This paper focuses
on the design of a roll autopilot for a fin stabilized and canard
controlled 122mm artillery rocket using state-dependent Riccati
equation technique. Initial spin is imparted to rocket during launch
and it quickly decays due to straight tail fins. After the spin phase, the
roll orientation of rocket is brought to zero with the canard deflection
commands generated by the roll autopilot. Roll autopilot has been
developed by considering uncoupled roll, pitch and yaw channels.
The canard actuator is modeled as a second-order nonlinear system.
Elements of the state weighing matrix for Riccati equation have been
chosen to be state dependent to exploit the design flexibility offered
by the Riccati equation technique. Simulation results under varying
conditions of flight demonstrate the wide operating range of the
proposed autopilot.
Abstract: A Personal Distributed Environment (PDE) is an
example of an IP-based system architecture designed for future
mobile communications. In a single PDE, there exist several Subnetworks
hosting devices located across the infrastructure, which will
inter-work with one another through the coordination of a Device
Management Entity (DME). Some of these Sub-networks are fixed
and some are mobile. In order to support Mobile Sub-networks
mobility in the PDE, the PDE-NEMO protocol was proposed. This
paper discussed the signalling cost analysis of PDE-NEMO by use of
a detailed simulation model. The paper started with the introduction
of the protocol, followed by the experiments and results and then
followed by discussions.
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: This article presents new current-mode oscillator circuits using CDTAs which is designed from block diagram. The proposed circuits consist of two CDTAs and two grounded capacitors. The condition of oscillation and the frequency of oscillation can be adjusted by electronic method. The circuits have high output impedance and use only grounded capacitors without any external resistor which is very appropriate to future development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.