Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: The internet has become an attractive avenue for
global e-business, e-learning, knowledge sharing, etc. Due to
continuous increase in the volume of web content, it is not practically
possible for a user to extract information by browsing and integrating
data from a huge amount of web sources retrieved by the existing
search engines. The semantic web technology enables advancement
in information extraction by providing a suite of tools to integrate
data from different sources. To take full advantage of semantic web,
it is necessary to annotate existing web pages into semantic web
pages. This research develops a tool, named OWIE (Ontology-based
Web Information Extraction), for semantic web annotation using
domain specific ontologies. The tool automatically extracts
information from html pages with the help of pre-defined ontologies
and gives them semantic representation. Two case studies have been
conducted to analyze the accuracy of OWIE.
Abstract: In this paper processes including large deformations of a rubber with hyperelastic material behavior are simulated by the RKPM method. Due to the loss of kronecker delta properties in the mesh less shape functions, the imposition of essential boundary conditions consumes significant CPU time in mesh free computations. In this work transformation method is used for imposition of essential boundary conditions. A RKPM material shape function is used in this analysis. The support of the material shape functions covers the same set of particles during material deformation and hence the transformation matrix is formed only once at the initial stages. A computer program in MATLAB is developed for simulations.
Abstract: Lean, which was initially developed by Toyota, is
widely implemented in other companies to improve competitiveness.
This research is an attempt to identify the adoption of lean in the
production system of Malaysian car manufacturer, Proton using case
study approach. To gain the in-depth information regarding lean
implementation, an activity on the assembly line called Set Parts
Supply (SPS) was studied. The result indicates that by using lean
principles, tools and techniques in the implementation of SPS enabled
to achieve the goals on safety, quality, cost, delivery and morale. The
implementation increased the size of the workspace, improved the
quality of assembly and the delivery of parts supply, reduced the
manpower, achieved cost savings on electricity and also increased the
motivation of manpower in respect of attendance at work. A
framework of SPS implementation is suggested as a contribution for
lean practices in production system.
Abstract: The contribution deals with analysis of identity style
at adolescents (N=463) at the age from 16 to 19 (the average age is
17,7 years). We used the Identity Style Inventory by Berzonsky,
distinguishing three basic, measured identity styles: informational,
normative, diffuse-avoidant identity style and also commitment. The
informational identity style influencing on personal adaptability,
coping strategies, quality of life and the normative identity style, it
means the style in which an individual takes on models of authorities
at self-defining were found to have the highest representation in the
studied group of adolescents by higher scores at girls in comparison
with boys. The normative identity style positively correlates with the
informational identity style. The diffuse-avoidant identity style was
found to be positively associated with maladaptive decisional
strategies, neuroticism and depressive reactions. There is the style,
in which the individual shifts aside defining his personality. In our
research sample the lowest score represents it and negatively
correlates with commitment, it means with coping strategies, thrust in
oneself and the surrounding world. The age of adolescents did not
significantly differentiate representation of identity style. We were
finding the model, in which informational and normative identity
style had positive relationship and the informational and diffuseavoidant
style had negative relationship, which were determinated
with commitment. In the same time the commitment is influenced
with other outside factors.
Abstract: The tagging data of (users, tags and resources) constitutes a folksonomy that is the user-driven and bottom-up approach to organizing and classifying information on the Web. Tagging data stored in the folksonomy include a lot of very useful information and knowledge. However, appropriate approach for analyzing tagging data and discovering hidden knowledge from them still remains one of the main problems on the folksonomy mining researches. In this paper, we have proposed a folksonomy data mining approach based on FCA for discovering hidden knowledge easily from folksonomy. Also we have demonstrated how our proposed approach can be applied in the collaborative tagging system through our experiment. Our proposed approach can be applied to some interesting areas such as social network analysis, semantic web mining and so on.
Abstract: The need to have standards has always been a priority
of all the disciplines in the world. Today, standards such as XML and
USB are trying to create a universal interface for their respective
areas. The information regarding every family in the discipline
addressed, must have a lot in common, known as Metadata. A lot of
work has been done in specific domains such as IEEE LOM and
MPEG-7 but they do not appeal to the universality of creating
Metadata for all entities, where we take an entity (object) as, not
restricted to Software Terms. This paper tries to address this problem
of universal Metadata Definition which may lead to increase in
precision of search.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified as a
CIM metamodel level mapping to a highly expressive subset of DLs
capable of capturing all the semantics of the models. The paper shows
how the proposed mapping can be used for automatic reasoning
about the management information models, as a design aid, by means
of new-generation CASE tools, thanks to the use of state-of-the-art
automatic reasoning systems that support the proposed logic and use
algorithms that are sound and complete with respect to the semantics.
Such a CASE tool framework has been developed by the authors and
its architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: Pabdeh shaly formation (Paleocene-Oligomiocene)
has been expanded in Fars, Khozestan and Lorestan. The lower
lithostratigraphic limit of this formation in Shiraz area is
distinguished from Gurpi formation by purple shale. Its upper limit is
gradational and conformable with Asmari formation. In order to
study sequence stratigraphy and microfacies of Pabdeh formation in
Shiraz area, one stratigraphic section have been chosen (Zanjiran
section). Petrographic studies resulted in the identification of 9
pelagic and calciturbidite microfacies. The calciturbidite microfacies
have been formed when the sea level was high, the rate of carbonate
deposition was high and it slumped into the deep marine. Sequence
stratigraphy studies show that Pabdeh formation in the studied zone
consists of two depositional sequences (DS) that the lower contact is
erosional (purple shale - type one, SBI or type two, SB2) and the
upper contact is correlative conformity (type two, SB2).
Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.
Abstract: The cDNA encoding the 326 amino acids of a Class I
basic chitinase gene from Leucaena leucocephala de Wit (KB3,
Genbank accession: AAM49597) was cloned under the control of
CaMV35S promoter in pCAMBIA 1300 and transferred to
Koshihikari. Calli of Koshihikari rice was transformed with
agrobacterium with this construct expressing the chitinase and β-
glucouronidase (GUS). The frequencies of calli 90 % has been
obtained from rice seedlings cultured on NB medium. The high
regeneration frequencies, 74% was obtained from calli cultured on
regeneration medium containing 4 mg/l BAP, and 7 g/l phytagel at
25°C. Various factors were studied in order to establish a procedure
for the transformation of Koshihikari Agrobacterium tumefaciens.
Supplementation of 50 mM acetosyringone to the medium during
coculivation was important to enhance the frequency to transient
transformation. The 4 week-old scutellum-derived calli were
excellent starting materials. Selection medium based on NB medium
supplement with 40 mg/l hygromycin and 400 mg/l cefotaxime were
an optimized medium for selection of transformed rice calli. The
percentage of transformation 70 was obtained. Recombinant calli and
regenerated rice plants were checked the expression of chitinase and
gus by PCR, northern blot gel, southern blot gel, and gus assay.
Chitinase and gus were expressed in all parts of recombinant rice.
The rice line expressing the KB3 chiitnase was more resistant to the
blast fungus Fusarium monoliforme than control line.
Abstract: The objective of this research is to develop the
performance indicators (PIs) in operational level for the Pre-hospital Emergency Medical Service (EMS) system employing in Thailand. This research started with ascertaining the current pre-hospital care
system. The team analyzed the strategies of Narerthorn, a government unit under the ministry of public health, and the existing PIs of the pre-hospital care. Afterwards, the current National Strategic Plan of EMS development (2008-2012) of the Emergency
Medical Institute of Thailand (EMIT) was considered using strategic
analysis to developed Strategy Map (SM) and identified the Success
Factors (SFs). The analysis results from strategy map and SFs were used to develop the Performance Indicators (PIs). To verify the set of
PIs, the team has interviewed with the relevant practitioners for the possibilities to implement the PIs. To this paper, it was to ascertain
that all the developed PIs support the objectives of the strategic plan. Nevertheless, the results showed that the operational level PIs suited
only with the first dimension of National Strategic Plan
(infrastructure and information technology development). Besides,
the SF was the infrastructure development (to contribute the EMS system to people throughout with standard and efficiency both in normally and disaster conditions). Finally, twenty-nine indicators
were developed from the analysis results of SM and SFs.
Abstract: This paper proposes a method, combining color and
layout features, for identifying documents captured from lowresolution
handheld devices. On one hand, the document image color
density surface is estimated and represented with an equivalent
ellipse and on the other hand, the document shallow layout structure
is computed and hierarchically represented. The combined color and
layout features are arranged in a symbolic file, which is unique for
each document and is called the document-s visual signature. Our
identification method first uses the color information in the
signatures in order to focus the search space on documents having a
similar color distribution, and finally selects the document having the
most similar layout structure in the remaining search space. Finally,
our experiment considers slide documents, which are often captured
using handheld devices.
Abstract: This paper presents a new steganography approach suitable for Arabic texts. It can be classified under steganography feature coding methods. The approach hides secret information bits within the letters benefiting from their inherited points. To note the specific letters holding secret bits, the scheme considers the two features, the existence of the points in the letters and the redundant Arabic extension character. We use the pointed letters with extension to hold the secret bit 'one' and the un-pointed letters with extension to hold 'zero'. This steganography technique is found attractive to other languages having similar texts to Arabic such as Persian and Urdu.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: Analytical solution of the first-order and third-order
shear deformation theories are developed to study the free vibration
behavior of simply supported functionally graded plates. The
material properties of plate are assumed to be graded in the thickness
direction as a power law distribution of volume fraction of the
constituents. The governing equations of functionally graded plates
are established by applying the Hamilton's principle and are solved
by using the Navier solution method. The influence of side-tothickness
ratio and constituent of volume fraction on the natural
frequencies are studied. The results are validated with the known
data in the literature.
Abstract: In this paper back-propagation artificial neural network
(BPANN) is employed to predict the deformation of the upsetting
process. To prepare a training set for BPANN, some finite element
simulations were carried out. The input data for the artificial neural
network are a set of parameters generated randomly (aspect ratio d/h,
material properties, temperature and coefficient of friction). The
output data are the coefficient of polynomial that fitted on barreling
curves. Neural network was trained using barreling curves generated
by finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process