Abstract: Linear induction motors are used in various industries
but they have some specific phenomena which are the causes for
some problems. The most important phenomenon is called end effect.
End effect decreases efficiency, power factor and output force and
unbalances the phase currents. This phenomenon is more important
in medium and high speeds machines. In this paper a factor, EEF , is
obtained by an accurate equivalent circuit model, to determine the
end effect intensity. In this way, all of effective design parameters on
end effect is described. Accuracy of this equivalent circuit model is
evaluated by two dimensional finite-element analysis using ANSYS.
The results show the accuracy of the equivalent circuit model.
Abstract: Determining how many virtual machines a Linux host
could run can be a challenge. One of tough missions is to find the
balance among performance, density and usability. Now KVM
hypervisor has become the most popular open source full
virtualization solution. It supports several ways of running guests with
more memory than host really has. Due to large differences between
minimum and maximum guest memory requirements, this paper
presents initial results on same-page merging, ballooning and live
migration techniques that aims at optimum memory usage on
KVM-based cloud platform. Given the design of initial experiments,
the results data is worth reference for system administrators. The
results from these experiments concluded that each method offers
different reliability tradeoff.
Abstract: Asphalt surfaces are exposed to various weather
conditions and dynamic loading caused by passing trucks and
vehicles. In such situations, asphalt cement shows so different
rheological-mechanical behavior. If asphalt cement isn-t compatible
enough, asphalt layer will be damaged immediately and expensive
repairing procedures should be performed then. To overcome this
problem, researchers study on mechanical improved asphalt cement.
In this study, bentonite was used in order to modify bitumen
characteristics and the modified bitumen's characteristics were
investigated by asphalt cement tests. Then, the optimal bitumen
content in various compounds was determined and asphalt samples
with different contents of additives were prepared and tested. Results
show using this kind of additive not only has caused improvement in
bitumen mechanical properties, but also improvement in Marshall
Parameters was achieved.
Abstract: There are a many of needs for the development of
SiC-based hydrogen sensor for harsh environment applications. We
fabricated and investigated Pd/Ta2O5/SiC-based hydrogen sensors
with MOS capacitor structure for high temperature process monitoring
and leak detection applications in such automotive, chemical and
petroleum industries as well as direct monitoring of combustion
processes. In this work, we used silicon carbide (SiC) as a substrate to
replace silicon which operating temperatures are limited to below
200°C. Tantalum oxide was investigated as dielectric layer which has
high permeability for hydrogen gas and high dielectric permittivity,
compared with silicon dioxide or silicon nitride. Then, electrical
response properties, such as I-V curve and dependence of capacitance
on hydrogen concentrations were analyzed in the temperature ranges
of room temperature to 500°C for performance evaluation of the
sensor.
Abstract: Organic farmers across Saskatchewan face soil
phosphorus (P) shortages. Due to the restriction on inputs in organic
systems, farmers rely on crop rotation and naturally-occurring
arbuscular mycorrhizal fungi (AMF) for plant P supply. Crop rotation
is important for disease, pest, and weed management. Crops that are
not colonized by AMF (non-mycorrhizal) can decrease colonization
of a following crop. An experiment was performed to quantify soil P
cycling in four cropping sequences under organic management and
determine if mustard (non-mycorrhizal) was delaying the
colonization of subsequent wheat. Soils from the four cropping
sequences were measured for inorganic soil P (Pi), AMF spore
density (SD), phospholipid fatty acid analysis (PLFA, for AMF
biomarker counts), and alkaline phosphatase activity (ALPase,
related to AMF metabolic activity). Plants were measured for AMF
colonization and P content and uptake of above-ground biomass. A
lack of difference in AMF activity indicated that mustard was not
depressing colonization. Instead, AMF colonization was largely
determined by crop type and crop rotation.
Abstract: Power System Security is a major concern in real time
operation. Conventional method of security evaluation consists of
performing continuous load flow and transient stability studies by
simulation program. This is highly time consuming and infeasible
for on-line application. Pattern Recognition (PR) is a promising
tool for on-line security evaluation. This paper proposes a Support
Vector Machine (SVM) based binary classification for static and
transient security evaluation. The proposed SVM based PR approach
is implemented on New England 39 Bus and IEEE 57 Bus systems.
The simulation results of SVM classifier is compared with the other
classifier algorithms like Method of Least Squares (MLS), Multi-
Layer Perceptron (MLP) and Linear Discriminant Analysis (LDA)
classifiers.
Abstract: This paper investigates several factors affecting the
cost of capital for listed Romanian companies. Although there is a
large amount of literature investigating the drivers of the cost of
capital internationally, there is currently little evidence from
emergent markets. Based on a sample of 19 Romanian listed
companies followed by financial analysts for the years 2008-2010,
according to Thomson Reuters- I/B/E/S data base, the paper confirms
the international trends, showing that size, corporate governance
policies, and growth are negatively correlated with the cost of capital.
Abstract: A new hybrid method to realise high-precision
distortion determination for optical ultra-precision 3D measurement
systems based on stereo cameras using active light projection is
introduced. It consists of two phases: the basic distortion
determination and the refinement. The refinement phase of the
procedure uses a plane surface and projected fringe patterns as
calibration tools to determine simultaneously the distortion of both
cameras within an iterative procedure. The new technique may be
performed in the state of the device “ready for measurement" which
avoids errors by a later adjustment. A considerable reduction of
distortion errors is achieved and leads to considerable improvements
of the accuracy of 3D measurements, especially in the precise
measurement of smooth surfaces.
Abstract: Internet Access Technologies (IAT) provide a means
through which Internet can be accessed. The choice of a suitable
Internet technology is increasingly becoming an important issue to
ISP clients. Currently, the choice of IAT is based on discretion and
intuition of the concerned managers and the reliance on ISPs. In this
paper we propose a model and designs algorithms that are used in the
Internet access technology specification. In the proposed model, three
ranking approaches are introduced; concurrent ranking, stepwise
ranking and weighted ranking. The model ranks the IAT based on
distance measures computed in ascending order while the global
ranking system assigns weights to each IAT according to the position
held in each ranking technique, determines the total weight of a
particular IAT and ranks them in descending order. The final output
is an objective ranking of IAT in descending order.
Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: In a metal forming process, the friction between the
material and the tools influences the process by modifying the stress
distribution of the workpiece. This frictional behaviour is often taken
into account by using a constant coefficient of friction in the finite
element simulations of sheet metal forming processes. However,
friction coefficient varies in time and space with many parameters.
The Stribeck friction model is investigated in this study to predict
springback behaviour of AA6061-T4 sheets during V-bending
process. The coefficient of friction in Stribeck curve depends on
sliding velocity and contact pressure. The plane-strain bending
process is simulated in ABAQUS/Standard. We compared the
computed punch load-stroke curves and springback related to the
constant coefficient of friction with the defined friction model. The
results clearly showed that the new friction model provides better
agreement between experiments and results of numerical simulations.
The influence of friction models on stress distribution in the
workpiece is also studied numerically
Abstract: We investigate nonfactorizable contributions to
D → ¤Ç¤Ç decay modes. We perform isospin analysis of the
nonfactorizable contributions to these decays. Obtaining the
factorizable contributions from spectator-quark diagrams using
= 3 C N , we determine nonfactorizable amplitudes for these decays
and predict their branching ratios.
Abstract: An attempt has been made to develop a
seminumerical model to study temperature variations in dermal
layers of human limbs. The model has been developed for two
dimensional steady state case. The human limb has been assumed to
have elliptical cross section. The dermal region has been divided
into three natural layers namely epidermis, dermis and subdermal
tissues. The model incorporates the effect of important physiological
parameters like blood mass flow rate, metabolic heat generation, and
thermal conductivity of the tissues. The outer surface of the limb is
exposed to the environment and it is assumed that heat loss takes
place at the outer surface by conduction, convection, radiation, and
evaporation. The temperature of inner core of the limb also varies at
the lower atmospheric temperature. Appropriate boundary conditions
have been framed based on the physical conditions of the problem.
Cubic splines approach has been employed along radial direction and
Fourier series along angular direction to obtain the solution. The
numerical results have been computed for different values of
eccentricity resembling with the elliptic cross section of the human
limbs. The numerical results have been used to obtain the
temperature profile and to study the relationships among the various
physiological parameters.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: The development of distributed systems has been affected by the need to accommodate an increasing degree of flexibility, adaptability, and autonomy. The Mobile Agent technology is emerging as an alternative to build a smart generation of highly distributed systems. In this work, we investigate the performance aspect of agent-based technologies for information retrieval. We present a comparative performance evaluation model of Mobile Agents versus Remote Method Invocation by means of an analytical approach. We demonstrate the effectiveness of mobile agents for dynamic code deployment and remote data processing by reducing total latency and at the same time producing minimum network traffic. We argue that exploiting agent-based technologies significantly enhances the performance of distributed systems in the domain of information retrieval.
Abstract: The purpose of this paper is to analyze determinants of
information security affecting adoption of the Web-based integrated
information systems (IIS). We introduced Web-based information
systems which are designed to formulate strategic plans for Peruvian
government. Theoretical model is proposed to test impact of
organizational factors (deterrent efforts and severity; preventive
efforts) and individual factors (information security threat; security
awareness) on intentions to proactively use the Web-based IIS .Our
empirical study results highlight that deterrent efforts and deterrent
severity have no significant influence on the proactive use intentions
of IIS, whereas, preventive efforts play an important role in proactive
use intentions of IIS. Thus, we suggest that organizations need to do
preventive efforts by introducing various information security
solutions, and try to improve information security awareness while
reducing the perceived information security threats.
Abstract: Khatunabad area is situated geologically in Urmieh-
Dokhtar magmatic belt in NW of Iran. In this research, studied area
has been investigated in order to recognize the potential copper and
molybdenum-bearing target areas. The survey layers include the
lithologic units, alteration, geochemical result, tectonics and copper
and molybdenum occurrence. As an accurate decision can have a
considerable effect on exploration plans, so in this efforts have been
made to make use of new combination method. For this purpose, the
analytical hierarchy process was used and revealed highly potential
copper and molybdenum mineralization areas. Based on achieved
results, geological perspective in north of studied area is appropriate
for advance stage, especially for subsurface exploration in future.
Abstract: This study include the effect of strain and storage
period and their interaction on some quantitative and qualitative traits
and percentages of the egg components in the eggs collected at the
start of production (at age 24 weeks). Eggs were divided into three
storage periods (1, 7 and 14) days under refrigerator temperature (5-
7)0C. Fifty seven eggs obtained randomly from each strain including
Isa Brown and Lohman White. General Linear Model within
SAS programme was used to analyze the collected data
and correlations between the studied traits were calculated for each
strain.Average egg weight (EW), Haugh Unit (HU), yolk index (YI),
yolk % (HP), albumin % (AP) and yolk to albumin ratio (YAR) was
56.629 gm, 87.968 %, 0.493, 22.13%, 67.74% and 32.76
respectively. Egg produced from ISA Brown surpassed those
produced by Lohman White significantly (P
Abstract: Various security APIs (Application Programming
Interfaces) are being used in a variety of application areas requiring
the information security function. However, these standards are not
compatible, and the developer must use those APIs selectively
depending on the application environment or the programming
language. To resolve this problem, we propose the standard draft of
the information security component, while SSL (Secure Sockets
Layer) using the confidentiality and integrity component interface has
been implemented to verify validity of the standard proposal. The
implemented SSL uses the lower-level SSL component when
establishing the RMI (Remote Method Invocation) communication
between components, as if the security algorithm had been
implemented by adding one more layer on the TCP/IP.
Abstract: This paper presents how the real-time chatter
prevention can be realized by feedback of acoustic cutting signal, and
the efficacy of the proposed adaptive spindle speed tuning algorithm is
verified by intensive experimental simulations. A pair of
microphones, perpendicular to each other, is used to acquire the
acoustic cutting signal resulting from milling chatter. A real-time
feedback control loop is constructed for spindle speed compensation
so that the milling process can be ensured to be within the stability
zone of stability lobe diagram. Acoustic Chatter Signal Index (ACSI)
and Spindle Speed Compensation Strategy (SSCS) are proposed to
quantify the acoustic signal and actively tune the spindle speed
respectively. By converting the acoustic feedback signal into ACSI,
an appropriate Spindle Speed Compensation Rate (SSCR) can be
determined by SSCS based on real-time chatter level or ACSI.
Accordingly, the compensation command, referred to as Added-On
Voltage (AOV), is applied to increase/decrease the spindle motor
speed. By inspection on the precision and quality of the workpiece
surface after milling, the efficacy of the real-time chatter prevention
strategy via acoustic signal feedback is further assured.