Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: The present study was conducted to investigate the
response of plants exposed to lignite-based thermal power plant
emission. For this purpose, five plant species were collected from 1.0
km distance (polluted site) and control plants were collected from
20.0 km distance (control site) to thermal power plant. The common
tree species Cassia siamea Lamk., Polyalthia longifolia. Sonn,
Acacia longifolia (Andrews) Wild., Azadirachta indica A.Juss, Ficus
religiosa L. were selected as test plants. Photosynthetic pigments
changes (chlorophyll a, chlorophyll b and carotenoids) and rubisco
enzyme modifications were studied. Reduction was observed in the
photosynthetic pigments of plants growing in polluted site and also
large sub unit of the rubisco enzyme was degraded in Azadirachta
indica A. Juss collected from polluted site.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.
Abstract: The Chinese Postman Problem (CPP) is one of the
classical problems in graph theory and is applicable in a wide range
of fields. With the rapid development of hybrid systems and model
based testing, Chinese Postman Problem with Time Dependent Travel
Times (CPPTDT) becomes more realistic than the classical problems.
In the literature, we have proposed the first integer programming
formulation for the CPPTDT problem, namely, circuit formulation,
based on which some polyhedral results are investigated and a cutting
plane algorithm is also designed. However, there exists a main drawback:
the circuit formulation is only available for solving the special
instances with all circuits passing through the origin. Therefore, this
paper proposes a new integer programming formulation for solving
all the general instances of CPPTDT. Moreover, the size of the circuit
formulation is too large, which is reduced dramatically here. Thus, it
is possible to design more efficient algorithm for solving the CPPTDT
in the future research.
Abstract: This paper presents a genetic algorithm based
approach for solving security constrained optimal power flow
problem (SCOPF) including FACTS devices. The optimal location of
FACTS devices are identified using an index called overload index
and the optimal values are obtained using an enhanced genetic
algorithm. The optimal allocation by the proposed method optimizes
the investment, taking into account its effects on security in terms of
the alleviation of line overloads. The proposed approach has been
tested on IEEE-30 bus system to show the effectiveness of the
proposed algorithm for solving the SCOPF problem.
Abstract: This paper focuses on analyzing medical diagnostic data using classification rules in data mining and context reduction in formal concept analysis. It helps in finding redundancies among the various medical examination tests used in diagnosis of a disease. Classification rules have been derived from positive and negative association rules using the Concept lattice structure of the Formal Concept Analysis. Context reduction technique given in Formal Concept Analysis along with classification rules has been used to find redundancies among the various medical examination tests. Also it finds out whether expensive medical tests can be replaced by some cheaper tests.
Abstract: Automotive engine air-ratio plays an important role of
emissions and fuel consumption reduction while maintains
satisfactory engine power among all of the engine control variables. In
order to effectively control the air-ratio, this paper presents a model
predictive fuzzy control algorithm based on online least-squares
support vector machines prediction model and fuzzy logic optimizer.
The proposed control algorithm was also implemented on a real car for
testing and the results are highly satisfactory. Experimental results
show that the proposed control algorithm can regulate the engine
air-ratio to the stoichiometric value, 1.0, under external disturbance
with less than 5% tolerance.
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: The study investigates the relationship between
education level, workplace learning behaviors, psychological
empowerment and burnout in a sample of 191 teachers. We
hypothesized that education level will positively affect psychological
state of increased empowerment and decreased burnout, and we
purposed that these effects will be mediated by workplace learning
behaviors. We used multiple regression analyses to test the model
that included also the 6 following control variables: The teachers'
age, gender, and teaching tenure; the schools' religious level, the
pupils' needs: regular/ special needs, and the class level: elementary/
high school. The results support the purposed mediating model.
Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.
Abstract: This paper presents functionality of negotiation agent
on value-based design decision. The functionality is based on the
characteristics of the system and goal specification. A Prometheus
Design Tool model was used for developing the system. Group
functionality will be the attribute for negotiation agents, which
comprises a coordinator agent and decision- maker agent. The results
of the testing of the system to a building system selection on valuebased
decision environment are also presented.
Abstract: The purpose of this study is to investigate the influence of breaststroke swimming exercise to improving the peak expiratory flow. Methode: This study used 17 students of men aged 19-21 years, APE values measured before and after the study. Style swimming workout done in accordance with a program that has been made. Result: Value of peak expiratory flow in male students obtained on average before exercise (530 ± 15 811) liters / min and after doing the exercises (540.59 ± 17 092) liters / minute. Paired ttest showed t = -6.446 and p = 0.000, which means there are differences in peak expiratory flow values before and after exercise swimming breaststroke. Conclusion: The conclusion is the breaststroke swimming exercise can be improving of peak expiratory flow.
Abstract: One of the most basic functions of control engineers is
tuning of controllers. There are always several process loops in the
plant necessitate of tuning. The auto tuned Proportional Integral
Derivative (PID) Controllers are designed for applications where
large load changes are expected or the need for extreme accuracy and
fast response time exists. The algorithm presented in this paper is
used for the tuning PID controller to obtain its parameters with a
minimum computing complexity. It requires continuous analysis of
variation in few parameters, and let the program to do the plant test
and calculate the controller parameters to adjust and optimize the
variables for the best performance. The algorithm developed needs
less time as compared to a normal step response test for continuous
tuning of the PID through gain scheduling.
Abstract: Traditionally, project scheduling and material planning have been treated independently. In this research, a mixed integer programming model is presented to integrate project scheduling and materials ordering problems. The goal is to minimize the total material holding and ordering costs. In addition, an efficient metaheuristic algorithm is proposed to solve the model. The proposed algorithm is computationally tested, the results are analyzed, and conclusions are given.
Abstract: This paper proposes, for the first time, how the
challenges facing the guard-band designs including the margin
assist-circuits scheme for the screening-test in the coming process
generations should be addressed. The increased screening error
impacts are discussed based on the proposed statistical analysis
models. It has been shown that the yield-loss caused by the
misjudgment on the screening test would become 5-orders of
magnitude larger than that for the conventional one when the
amplitude of random telegraph noise (RTN) caused variations
approaches to that of random dopant fluctuation. Three fitting methods
to approximate the RTN caused complex Gamma mixtures
distributions by the simple Gaussian mixtures model (GMM) are
proposed and compared. It has been verified that the proposed
methods can reduce the error of the fail-bit predictions by 4-orders of
magnitude.