Abstract: Tritium activity concentration in Danube river water
in Serbia has been determinate using a liquid scintillation counter
Quantulus 1220. During December 2010, water samples were taken
along the entire course of Danube through Serbia, from Hungarian-
Serbian to Romanian-Serbian border. This investigation is very
important because of the nearness of nuclear reactor Paks in
Hungary. Sample preparation was performed by standard test method
using Optiphase HiSafe 3 scintillation cocktail. We used a rapid
method for the preparation of environmental samples, without
electrolytic enrichment.
Abstract: (Bi0.5Na0.5)TiO3 doped with 8 mol % BaTiO3 powder
(BNT-BT0.08), prepared by sol-gel method was compacted and
sintered by Spark Plasma Sintering (SPS) process. The influence of
SPS temperature on the densification of BNT-BT0.08 ceramic was
investigated. Starting from sol-gel nanopowder of BNT-BT
containing 8 mol % BaTiO3 with an average particles size of about
30 nm, were obtained ceramics with density around 98 % of the
theoretical density value when the SPS temperature used was about
850 °C. The average grain size of the resulting ceramics was 80 nm.
The BNT-BT0.08 ceramic sample obtained by SPS method has shown
good electric properties at various frequencies.
Abstract: The increasing importance of FlexRay systems in
automotive domain inspires unceasingly relative researches. One
primary issue among researches is to verify the reliability of FlexRay
systems either from protocol aspect or from system design aspect.
However, research rarely discusses the effect of network topology on
the system reliability. In this paper, we will illustrate how to model
the reliability of FlexRay systems with various network topologies by
a well-known probabilistic reasoning technology, Bayesian Network.
In this illustration, we especially investigate the effectiveness of error
containment built in star topology and fault-tolerant midpoint
synchronization algorithm adopted in FlexRay communication
protocol. Through a FlexRay steer-by-wire case study, the influence
of different topologies on the failure probability of the FlexRay steerby-
wire system is demonstrated. The notable value of this research is
to show that the Bayesian Network inference is a powerful and
feasible method for the reliability assessment of FlexRay systems.
Abstract: The InAlGaN alloy has only recently began receiving
serious attention into its growth and application. High quality InGaN
films have led to the development of light emitting diodes (LEDs) and
blue laser diodes (LDs). The quaternary InAlGaN however, represents
a more versatile material since the bandgap and lattice constant can be
independently varied. We report an ultraviolet (UV) quaternary
InAlGaN multi-quantum wells (MQWs) LD study by using the
simulation program of Integrated System Engineering (ISE TCAD).
Advanced physical models of semiconductor properties were used in
order to obtain an optimized structure. The device performance which
is affected by piezoelectric and thermal effects was studied via
drift-diffusion model for carrier transport, optical gain and loss. The
optical performance of the UV LD with different numbers of quantum
wells was numerically investigated. The main peak of the emission
wavelength for double quantum wells (DQWs) was shifted from 358
to 355.8 nm when the forward current was increased. Preliminary
simulated results indicated that better output performance and lower
threshold current could be obtained when the quantum number is four,
with output power of 130 mW and threshold current of 140 mA.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: Ti-6Al-4V alloy has demonstrated a high strength to
weight ratio as well as good properties at high temperature. The
successful application of the alloy in some important areas depends
on suitable joining techniques. Friction welding has many
advantageous features to be chosen for joining Titanium alloys. The
present work investigates the feasibility of producing similar metal
joints of this Titanium alloy by rotary friction welding method. The
joints are produced at three different speeds and the performances of
the welded joints are evaluated by conducting microstructure studies,
Vickers Hardness and tensile tests at the joints. It is found that the
weld joints produced are sound and the ductile fractures in the tensile
weld specimens occur at locations away from the welded joints. It is
also found that a rotational speed of 1500 RPM can produce a very
good weld, with other parameters kept constant.
Abstract: Artificial Neural Networks (ANNs) have been used successfully in many scientific, industrial and business domains as a method for extracting knowledge from vast amounts of data. However the use of ANN techniques in the sporting domain has been limited. In professional sport, data is stored on many aspects of teams, games, training and players. Sporting organisations have begun to realise that there is a wealth of untapped knowledge contained in the data and there is great interest in techniques to utilise this data. This study will use player data from the elite Australian Football League (AFL) competition to train and test ANNs with the aim to predict the onset of injuries. The results demonstrate that an accuracy of 82.9% was achieved by the ANNs’ predictions across all examples with 94.5% of all injuries correctly predicted. These initial findings suggest that ANNs may have the potential to assist sporting clubs in the prediction of injuries.
Abstract: The wrinkling of a thin elastic bi-annular plate with piecewise-constant mechanical properties, subjected to radial stretching, is considered. The critical wrinkling stretching loading and the corresponding wrinkling patterns are extensively investigated, together with the roles played by both the geometrical and mechanical parameters.
Abstract: This paper presents the new results of energy plant –
rye and triticale at yellow ripeness and ripe, pre-treatment in high
pressure steam reactor and monosaccharide extraction. There were
investigated the influence of steam pressure (20 to 22 bar), retention
duration (180 to 240 s) and catalytic sulphuric acid concentration
strength (0 to 0.5 %) on the pre-treatment process, contents of
monosaccharides (glucose, arabinose, xylose, mannose) and
undesirable by-compounds (furfural and HMF) in the reactor. The
study has determined that the largest amount of monosaccharides
(37.2 % of glucose, 2.7 % of arabinose, 8.4 % of xylose, and 1.3 %
of mannose) was received in the rye at ripe, the samples of which
were mixed with 0.5 % concentration of catalytic sulphuric acid, and
hydrolysed in the reactor, where the pressure was 20 bar, whereas the
reaction time – 240 s.
Abstract: Competing risks survival data that comprises of more
than one type of event has been used in many applications, and one
of these is in clinical study (e.g. in breast cancer study). The
decision tree method can be extended to competing risks survival
data by modifying the split function so as to accommodate two or
more risks which might be dependent on each other. Recently,
researchers have constructed some decision trees for recurrent
survival time data using frailty and marginal modelling. We further
extended the method for the case of competing risks. In this paper,
we developed the decision tree method for competing risks survival
time data based on proportional hazards for subdistribution of
competing risks. In particular, we grow a tree by using deviance
statistic. The application of breast cancer data is presented. Finally,
to investigate the performance of the proposed method, simulation
studies on identification of true group of observations were executed.
Abstract: This paper investigates the problem of absolute stability and robust stability of a class of Lur-e systems with neutral type and time-varying delays. By using Lyapunov direct method and linear matrix inequality technique, new delay-dependent stability criteria are obtained and formulated in terms of linear matrix inequalities (LMIs) which are easy to check the stability of the considered systems. To obtain less conservative stability conditions, an operator is defined to construct the Lyapunov functional. Also, the free weighting matrices approach combining a matrix inequality technique is used to reduce the entailed conservativeness. Numerical examples are given to indicate significant improvements over some existing results.
Abstract: The microbial production of ethanol from biodiesel¬derived crude glycerol by Enterobacter aerogenes TISTR1468, under micro-aerobic and anaerobic conditions, was investigated. The experimental results showed that micro-aerobic conditions were more favorable for cellular growth (4.0 g/L DCW), ethanol production (20.7 g/L) as well as the ethanol yield (0.47 g/g glycerol) than anaerobic conditions (1.2 g/L DCW, 6.3 g/L ethanol and 0.72 g/g glycerol, respectively). Crude glycerol (100 g/L) was consumed completely with the rate of 1.80 g/L/h. Two-stage fermentation (combination of micro-aerobic and anaerobic condition) exhibited higher ethanol production (24.5 g/L) than using one-stage fermentation (either micro-aerobic or anaerobic condition. The two- stage configuration, exhibited slightly higher crude glycerol consumption rate (1.81 g/L/h), as well as ethanol yield (0.56 g/g) than the one-stage configuration. Therefore, two-stage process was selected for ethanol production from E. aerogenes TISTR1468 in scale-up studies.
Abstract: Recent developments in automotive technology are focused on economy, comfort and safety. Vehicle tracking and collision detection systems are attracting attention of many investigators focused on safety of driving in the field of automotive mechatronics. In this paper, a vision-based vehicle detection system is presented. Developed system is intended to be used in collision detection and driver alert. The system uses RGB images captured by a camera in a car driven in the highway. Images captured by the moving camera are used to detect the moving vehicles in the image. A vehicle ahead of the camera is detected in daylight conditions. The proposed method detects moving vehicles by subtracting successive images. Plate height of the vehicle is determined by using a plate recognition algorithm. Distance of the moving object is calculated by using the plate height. After determination of the distance of the moving vehicle relative speed of the vehicle and Time-to-Collision are calculated by using distances measured in successive images. Results obtained in road tests are discussed in order to validate the use of the proposed method.
Abstract: This paper addresses a current problem that occurs among Thai internet service providers with regard to bandwidth network quality management. The IPSTAR department of Telecom Organization of Thailand public company (TOT); the largest internet service provider in Thailand, is the case study to analyze the problem that exists. The Internet bandwidth network quality management (iBWQM) framework is mainly applied to the problem that has been found. Bandwidth management policy (BMP) and quality of service (QoS) are two antecedents of iBWQM. This paper investigates internet user behavior, marketing demand and network operation views in order to determine bandwidth management policy (e.g. quota management, scheduling and malicious management). The congestion of bandwidth is also analyzed to enhance quality of service (QoS). Moreover, the iBWQM framework is able to improve the quality of service and increase bandwidth utilization, minimize complaint rate concerns to slow speed, and provide network planning guidelines through Thai Internet services providers.
Abstract: The main aims in this research are to study the solid
waste generation in the Faculty of Engineering and Built
Environment in the UKM and at the same time to determine
composition and some of the waste characteristics likewise: moisture
content, density, pH and C/N ratio. For this purpose multiple
campaigns were conducted to collect the wastes produced in all
hostels, faculties, offices and so on, during 24th of February till 2nd
of March 2009, measure and investigate them with regard to both
physical and chemical characteristics leading to highlight the
necessary management policies. Research locations are Faculty of
Engineering and the Canteen nearby that. From the result gained, the
most suitable solid waste management solution will be proposed to
UKM. The average solid waste generation rate in UKM is 203.38
kg/day. The composition of solid waste generated are glass, plastic,
metal, aluminum, organic and inorganic waste and others waste.
From the laboratory result, the average moisture content, density, pH
and C/N ratio values from the solid waste generated are 49.74%,
165.1 kg/m3, 5.3, and 7:1 respectively. Since, the food waste (organic
waste) were the most dominant component, around 62% from the
total waste generated hence, the most suitable solid waste
management solution is composting.
Abstract: Titanium dioxide coatings were deposited by utilizing
atmospheric plasma spraying (APS) system. The agglomerated nanopowder
and different spraying parameters were used to determine
their influences on the microstructure surface feature and photoabsorption
of the coatings. The microstructure of as-sprayed TiO2
coatings were characterized by scanning electron microscope (SEM).
Surface characteristics were investigated by Fourier Transform
Infrared (FT-IR). The photo absorption was determined by UV-VIS
spectrophotometer. It is found that the spray parameters have an
influence on the microstructure, surface feature and photo-absorption
of the TiO2 coatings.
Abstract: This research assesses the value of the brand personality and its influence on consumer-s decision making, through relational variables, after receiving a text message ad. An empirical study, in which 380 participants have received an SMS ad, confirms that brand personality does actually influence the brand trust as well as the attachment and commitment. The levels of sensitivity and involvement have an impact on the brand personality and the related variables to it.
Abstract: In this paper the multi-mode resource-constrained project scheduling problem with discounted cash flows is considered. Minimizing the makespan and maximization the net present value (NPV) are the two common objectives that have been investigated in the literature. We apply one evolutionary algorithm named multiobjective particle swarm optimization (MOPSO) to find Pareto front solutions. We used standard sets of instances from the project scheduling problem library (PSPLIB). The results are computationally compared respect to different metrics taken from the literature on evolutionary multi-objective optimization.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: Most of the biclustering/projected clustering algorithms are based either on the Euclidean distance or correlation coefficient which capture only linear relationships. However, in many applications, like gene expression data and word-document data, non linear relationships may exist between the objects. Mutual Information between two variables provides a more general criterion to investigate dependencies amongst variables. In this paper, we improve upon our previous algorithm that uses mutual information for biclustering in terms of computation time and also the type of clusters identified. The algorithm is able to find biclusters with mixed relationships and is faster than the previous one. To the best of our knowledge, none of the other existing algorithms for biclustering have used mutual information as a similarity measure. We present the experimental results on synthetic data as well as on the yeast expression data. Biclusters on the yeast data were found to be biologically and statistically significant using GO Tool Box and FuncAssociate.