Abstract: It is necessary to evaluate the bridges conditions and
strengthen bridges or parts of them. The reinforcement necessary due
to some reasons can be summarized as: First, a changing in use of
bridge could produce internal forces in a part of structural which
exceed the existing cross-sectional capacity. Second, bridges may
also need reinforcement because damage due to external factors
which reduced the cross-sectional resistance to external loads. One of
other factors could listed here its misdesign in some details, like
safety of bridge or part of its.This article identify the design demands
of Qing Shan bridge located in is in Heilongjiang Province He gang -
Nen Jiang Road 303 provincial highway, Wudalianchi area, China, is
an important bridge in the urban areas. The investigation program
was include the observation and evaluate the damage in T- section
concrete beams , prestressed concrete box girder bridges section in
additional evaluate the whole state of bridge includes the pier ,
abutments , bridge decks, wings , bearing and capping beam, joints,
........etc. The test results show that the bridges in general structural
condition are good. T beam span No 10 were observed, crack
extended upward along the ribbed T beam, and continue to the T
beam flange. Crack width varying between 0.1mm to 0.4mm, the
maximum about 0.4mm. The bridge needs to be improved flexural
bending strength especially at for T beam section.
Abstract: A decomposition of a graph G is a collection ψ of subgraphs H1,H2, . . . , Hr of G such that every edge of G belongs to exactly one Hi. If each Hi is either an induced path or an induced cycle in G, then ψ is called an induced path decomposition of G. The minimum cardinality of an induced path decomposition of G is called the induced path decomposition number of G and is denoted by πi(G). In this paper we initiate a study of this parameter.
Abstract: The social force model which belongs to the
microscopic pedestrian studies has been considered as the supremacy
by many researchers and due to the main feature of reproducing the
self-organized phenomena resulted from pedestrian dynamic. The
Preferred Force which is a measurement of pedestrian-s motivation to
adapt his actual velocity to his desired velocity is an essential term on
which the model was set up. This Force has gone through stages of
development: first of all, Helbing and Molnar (1995) have modeled
the original force for the normal situation. Second, Helbing and his
co-workers (2000) have incorporated the panic situation into this
force by incorporating the panic parameter to account for the panic
situations. Third, Lakoba and Kaup (2005) have provided the
pedestrians some kind of intelligence by incorporating aspects of the
decision-making capability. In this paper, the authors analyze the
most important incorporations into the model regarding the preferred
force. They make comparisons between the different factors of these
incorporations. Furthermore, to enhance the decision-making ability
of the pedestrians, they introduce additional features such as the
familiarity factor to the preferred force to let it appear more
representative of what actually happens in reality.
Abstract: The paper focuses on the enhanced stiffness modeling
of robotic manipulators by taking into account influence of the external force/torque acting upon the end point. It implements the
virtual joint technique that describes the compliance of manipulator elements by a set of localized six-dimensional springs separated by
rigid links and perfect joints. In contrast to the conventional
formulation, which is valid for the unloaded mode and small
displacements, the proposed approach implicitly assumes that the loading leads to the non-negligible changes of the manipulator posture and corresponding amendment of the Jacobian. The
developed numerical technique allows computing the static
equilibrium and relevant force/torque reaction of the manipulator for
any given displacement of the end-effector. This enables designer
detecting essentially nonlinear effects in elastic behavior of
manipulator, similar to the buckling of beam elements. It is also proposed the linearization procedure that is based on the inversion of
the dedicated matrix composed of the stiffness parameters of the
virtual springs and the Jacobians/Hessians of the active and passive
joints. The developed technique is illustrated by an application example that deals with the stiffness analysis of a parallel
manipulator of the Orthoglide family
Abstract: Failure in mastery of motor skills proficiency during
childhood has been seen as a detrimental factor for children to be
physically active. Lack of motor skills proficiency tends to reduce
children’s competency and confidence level to participate in physical
activity. As a consequence of less participation in physical activity,
children will turn to be overweight and obese. It has been suggested
that children who master motor skill proficiency will be more
involved in physical activity thus preventing them from being
overweight. Obesity has become a serious childhood health issues
worldwide. Previous studies have found that children who were
overweight and obese were generally less active however these
studies focused on one gender. This study aims to compare motor
skill proficiency of underweight, normal-weight, overweight and
obese young boys as well as to determine the relationship between
motor skills proficiency and body composition. 112 boys aged
between 8 to 10 years old participated in this study. Participants were
assigned to four groups; underweight, normal-weight, overweight and
obese using BMI-age percentile chart for children. Bruininks-
Oseretsky Test Second Edition-Short Form was administered to
assess their motor skill proficiency. Meanwhile, body composition
was determined by the skinfold thickness measurement. Result
indicated that underweight and normal children were superior in
motor skills proficiency compared to overweight and obese children
(p < 0.05). A significant strong inverse correlation between motor
skills proficiency and body composition (r = -0.849) is noted. The
findings of this study could be explained by non-contributory mass
that carried by overweight and obese children leads to biomechanical
movement inefficiency which will become detrimental to motor skills
proficiency. It can be concluded that motor skills proficiency is
inversely correlated with body composition.
Abstract: Ontology is a terminology which is used in artificial
intelligence with different meanings. Ontology researching has an
important role in computer science and practical applications,
especially distributed knowledge systems. In this paper we present an
ontology which is called Computational Object Knowledge Base
Ontology. It has been used in designing some knowledge base
systems for solving problems such as the system that supports
studying knowledge and solving analytic geometry problems, the
program for studying and solving problems in Plane Geometry, the
knowledge system in linear algebra.
Abstract: The Siemens Healthcare Sector is one of the world's
largest suppliers to the healthcare industry and a trendsetter in
medical imaging and therapy, laboratory diagnostics, medical
information technology, and hearing aids.
Siemens offers its customers products and solutions for the entire
range of patient care from a single source – from prevention and
early detection to diagnosis, and on to treatment and aftercare. By
optimizing clinical workflows for the most common diseases,
Siemens also makes healthcare faster, better, and more cost effective.
The optimization of clinical workflows requires a
multidisciplinary focus and a collaborative approach of e.g. medical
advisors, researchers and scientists as well as healthcare economists.
This new form of collaboration brings together experts with deep
technical experience, physicians with specialized medical knowledge
as well as people with comprehensive knowledge about health
economics.
As Charles Darwin is often quoted as saying, “It is neither the
strongest of the species that survive, nor the most intelligent, but the
one most responsive to change," We believe that those who can
successfully manage this change will emerge as winners, with
valuable competitive advantage.
Current medical information and knowledge are some of the core
assets in the healthcare industry. The main issue is to connect
knowledge holders and knowledge recipients from various
disciplines efficiently in order to spread and distribute knowledge.
Abstract: Human Computer Interaction (HCI) has been an
emerging field that draws in the experts from various fields to
enhance the application of computer programs and the ease of
computer users. HCI has much to do with learning and cognition and
an emerging approach to learning and problem-solving is problembased
learning (PBL). The processes of PBL involve important
cognitive functions in the various stages. This paper will illustrate
how closely related fields to HCI, PBL and cognitive psychology can
benefit from informing each other through analysing various
cognitive functions. Several cognitive functions from cognitive
function disc (CFD) would be presented and discussed in relation to
human-computer interface. This paper concludes with the
implications of bridging the gaps amongst these disciplines.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: It is sometimes difficult to differentiate between
innocent murmurs and pathological murmurs during auscultation. In
these difficult cases, an intelligent stethoscope with decision support
abilities would be of great value. In this study, using a dog model,
phonocardiographic recordings were obtained from 27 boxer dogs
with various degrees of aortic stenosis (AS) severity. As a reference
for severity assessment, continuous wave Doppler was used. The data
were analyzed with recurrence quantification analysis (RQA) with
the aim to find features able to distinguish innocent murmurs from
murmurs caused by AS. Four out of eight investigated RQA features
showed significant differences between innocent murmurs and
pathological murmurs. Using a plain linear discriminant analysis
classifier, the best pair of features (recurrence rate and entropy)
resulted in a sensitivity of 90% and a specificity of 88%. In
conclusion, RQA provide valid features which can be used for
differentiation between innocent murmurs and murmurs caused by
AS.
Abstract: Over the past few years, companies in developing
countries have implemented enterprise resource planning (ERP)
systems. Regardless of the various benefits of the ERP system, its
adoption and implementation have not been without problems. Many
companies have assigned considerable organizational resources to
their ERP projects, but have encountered unexpected challenges.
Neglecting a number of important factors in ERP projects might lead
to failure instead of success. User satisfaction is among those factors
that has a major influence on ERP implementation success. So, this
paper intends to investigate the key factors that create ERP users-
satisfaction and to discover whether ERP users- satisfaction varies
among different users- profiles. The study was conducted using a
survey questionnaire which was distributed to ERP users in Iranian
organizations. A total of 384 responses were collected and analyzed.
The findings indicated that younger ERP users tend to be more
satisfied with ERP systems. Furthermore, ERP users with more
experiences in IT and also more educated users have more
satisfaction with ERP softwares. However, the study found no
satisfaction differences between men and women users.
Abstract: As wireless sensor networks are energy constraint networks
so energy efficiency of sensor nodes is the main design issue.
Clustering of nodes is an energy efficient approach. It prolongs the
lifetime of wireless sensor networks by avoiding long distance communication.
Clustering algorithms operate in rounds. Performance of
clustering algorithm depends upon the round time. A large round
time consumes more energy of cluster heads while a small round
time causes frequent re-clustering. So existing clustering algorithms
apply a trade off to round time and calculate it from the initial
parameters of networks. But it is not appropriate to use initial
parameters based round time value throughout the network lifetime
because wireless sensor networks are dynamic in nature (nodes can be
added to the network or some nodes go out of energy). In this paper
a variable round time approach is proposed that calculates round
time depending upon the number of active nodes remaining in the
field. The proposed approach makes the clustering algorithm adaptive
to network dynamics. For simulation the approach is implemented
with LEACH in NS-2 and the results show that there is 6% increase
in network lifetime, 7% increase in 50% node death time and 5%
improvement over the data units gathered at the base station.
Abstract: Deep cold rolling (DCR) and low plasticity burnishing (LPB) process are cold working processes, which easily produce a smooth and work-hardened surface by plastic deformation of surface irregularities. The present study focuses on the surface roughness and surface hardness aspects of AISI 4140 work material, using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in order to identify the predominant factors amongst the selected parameters. They were then categorized in order of significance followed by setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. In the present work, the influence of main process parameters (force, feed rate, number of tool passes/overruns, initial roughness of the work piece, ball material, ball diameter and lubricant used) on the surface roughness and the hardness of AISI 4140 steel were studied for both LPB and DCR process and the results are compared. It was observed that by using LPB process surface hardness has been improved by 167% and in DCR process surface hardness has been improved by 442%. It was also found that the force, ball diameter, number of tool passes and initial roughness of the workpiece are the most pronounced parameters, which has a significant effect on the work piece-s surface during deep cold rolling and low plasticity burnishing process.
Abstract: Computer programming is considered a very difficult
course by many computer science students. The reasons for the
difficulties include cognitive load involved in programming,
different learning styles of students, instructional methodology and
the choice of the programming languages. To reduce the difficulties
the following have been tried: pair programming, program
visualization, different learning styles etc. However, these efforts
have produced limited success. This paper reviews the problem and
proposes a framework to help students overcome the difficulties
involved.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: Application of wood in rural construction is diffused
all around the world since remote times. However, its inclusion in
structural design deserves strong support from broad knowledge of
material properties. The pertinent literature reveals the application of
optical methods in determining the complete field displacement on
bodies exhibiting regular as well as irregular surfaces. The use of
moiré techniques in experimental mechanics consists in analyzing the
patterns generated on the body surface before and after deformation.
The objective of this research work is to study the qualitative
deformation behavior of wooden testing specimens under specific
loading situations. The experiment setup follows the literature
description of shadow moiré methods. Results indicate strong
anisotropy influence of the generated displacement field. Important
qualitative as well as quantitative stress and strain distribution were
obtained wooden members which are applicable to rural
constructions.
Abstract: De novo genome assembly is always fragmented. Assembly fragmentation is more serious using the popular next generation sequencing (NGS) data because NGS sequences are shorter than the traditional Sanger sequences. As the data throughput of NGS is high, the fragmentations in assemblies are usually not the result of missing data. On the contrary, the assembled sequences, called contigs, are often connected to more than one other contigs in a complicated manner, leading to the fragmentations. False connections in such complicated connections between contigs, named a contig graph, are inevitable because of repeats and sequencing/assembly errors. Simplifying a contig graph by removing false connections directly improves genome assembly. In this work, we have developed a tool, SIMGraph, to resolve ambiguous connections between contigs using NGS data. Applying SIMGraph to the assembly of a fungus and a fish genome, we resolved 27.6% and 60.3% ambiguous contig connections, respectively. These results can reduce the experimental efforts in resolving contig connections.
Abstract: Construction of tunnels is connected with high
uncertainty in the field of costs, construction period, safety and
impact on surroundings. Risk management became therefore a
common part of tunnel projects, especially after a set of fatal
collapses occurred in 1990's. Such collapses are caused usually by
combination of factors that can be divided into three main groups, i.e.
unfavourable geological conditions, failures in the design and
planning or failures in the execution.
This paper suggests a procedure enabling quantification of the
excavation risk related to extraordinary accidents using FTA and
ETA tools. It will elaborate on a common process of risk analysis and
enable the transfer of information and experience between particular
tunnel construction projects. Further, it gives a guide for designers,
management and other participants, how to deal with risk of such
accidents and how to make qualified decisions based on a
probabilistic approach.
Abstract: This paper undertakes the problem of optimal
capacitor placement in a distribution system. The problem is how to
optimally determine the locations to install capacitors, the types and
sizes of capacitors to he installed and, during each load level,the
control settings of these capacitors in order that a desired objective
function is minimized while the load constraints,network constraints
and operational constraints (e.g. voltage profile) at different load
levels are satisfied. The problem is formulated as a combinatorial
optimization problem with a nondifferentiable objective function.
Four solution mythologies based on algorithms (GA),tabu search
(TS), and hybrid GA-SA algorithms are presented.The solution
methodologies are preceded by a sensitivity analysis to select the
candidate capacitor installation locations.
Abstract: The objectives of this study are to determine the role of media that influence the values, attitudes and behaviors of Thai youths. Analytical qualitative research techniques were used for this purpose. Data collection based techniques was used which were individual interviews and focus group discussions with journalists, sample of high school and university students, and parents. The results show that “Social Media" is still the most popular media for Thai youths. It is also still in the hands of the marketing business and it can motivate Thai youths to do so many things. The main reasons of media exposure are to find quality information that they want quickly, get satisfaction and can use social media to get more exciting and to build communities. They believe that the need for media and information literacy skills is defined as making judgments, personal integrity, training of family and the behavior of close friends.