Abstract: We present design, fabrication, and characterization of
a small (12 mm × 12 mm × 8 mm) movable railway vehicle for sensor
carrying. The miniature railway vehicle (MRV) was mainly composed
of a vibrational structure and three legs. A railway was designed and
fabricated to power and guide the MRV. It also transmits the sensed
data from the MRV to the signal processing unit. The MRV with legs
on the railway was moving due to its high-frequency vibration. A
model was derived to describe the motion. Besides, FEM simulations
were performed to design the legs. Then, the MRV and the railway
were fabricated by precision machining. Finally, an infrared sensor
was carried and tested. The result shows that the MRV without loading
was moving along the railway and its maximum speed was 12.2 mm/s.
Moreover, the testing signal was sensed by the MRV.
Abstract: The cable tower of Liede Bridge is a double-column curved-lever arched-beam portal framed structure. Being novel and unique in structure, its cable tower differs in complexity from traditional ones. This paper analyzes the ultimate load capacity of cable tower by adopting the finite element calculations and model tests which indicate that constitutive relations applied here give a better simulation of actual failure process of prestressed reinforced concrete. In vertical load, horizontal load and overloading tests, the stepped loading of the tower model is of linear relationship, and the test data has good repeatability. All suggests that the cable tower has good bearing capacity, rational design and high emergency capacity.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: Medical image modalities such as computed
tomography (CT), magnetic resonance imaging (MRI), ultrasound
(US), X-ray are adapted to diagnose disease. These modalities
provide flexible means of reviewing anatomical cross-sections and
physiological state in different parts of the human body. The raw
medical images have a huge file size and need large storage
requirements. So it should be such a way to reduce the size of those
image files to be valid for telemedicine applications. Thus the image
compression is a key factor to reduce the bit rate for transmission or
storage while maintaining an acceptable reproduction quality, but it is
natural to rise the question of how much an image can be compressed
and still preserve sufficient information for a given clinical
application. Many techniques for achieving data compression have
been introduced. In this study, three different MRI modalities which
are Brain, Spine and Knee have been compressed and reconstructed
using wavelet transform. Subjective and objective evaluation has
been done to investigate the clinical information quality of the
compressed images. For the objective evaluation, the results show
that the PSNR which indicates the quality of the reconstructed image
is ranging from (21.95 dB to 30.80 dB, 27.25 dB to 35.75 dB, and
26.93 dB to 34.93 dB) for Brain, Spine, and Knee respectively. For
the subjective evaluation test, the results show that the compression
ratio of 40:1 was acceptable for brain image, whereas for spine and
knee images 50:1 was acceptable.
Abstract: Rainfall data at fine resolution and knowledge of its
characteristics plays a major role in the efficient design and operation
of agricultural, telecommunication, runoff and erosion control as well
as water quality control systems. The paper is aimed to study the
statistical distribution of hourly rainfall depth for 12 representative
stations spread across Peninsular Malaysia. Hourly rainfall data of 10
to 22 years period were collected and its statistical characteristics
were estimated. Three probability distributions namely, Generalized
Pareto, Exponential and Gamma distributions were proposed to
model the hourly rainfall depth, and three goodness-of-fit tests,
namely, Kolmogorov-Sminov, Anderson-Darling and Chi-Squared
tests were used to evaluate their fitness. Result indicates that the east
cost of the Peninsular receives higher depth of rainfall as compared
to west coast. However, the rainfall frequency is found to be
irregular. Also result from the goodness-of-fit tests show that all the
three models fit the rainfall data at 1% level of significance.
However, Generalized Pareto fits better than Exponential and
Gamma distributions and is therefore recommended as the best fit.
Abstract: The large and small-scale shaking table tests, which
was conducted for investigating damage evolution of piles inside
liquefied soil, are numerically simulated and experimental verified by the3D nonlinear finite element analysis. Damage evolution of
elasto-plastic circular steel piles and reinforced concrete (RC) one with cracking and yield of reinforcement are focused on, and the failure patterns and residual damages are captured by the proposed constitutive models. The superstructure excitation behind quay wall is
reproduced as well.
Abstract: The purpose of this study was to elucidate the factors affecting antimicrobial effectiveness of essential oils against food spoilage and pathogenic bacteria. The minimum inhibition concentrations (MIC) of the essential oils, were determined by turbidimetric technique using Biocreen C, analyzer. The effects of pH ranging from 7.3 to 5.5 in absence and presence of essential oils and/or NaCl on the lag time and mean generation time of the bacteria at 370C, were carried out and results were determined showed that, combination of low pH and essential oil at 370C had additive effects against the test micro-organisms. The combination of 1.2 % (w/v) of NaCl and clove essential oil at 0.0325% (v/v) was effective against E. coli. The use of concentrations less than MIC in combination with low pH and or NaCl has the potential of being used as an alternative to “traditional food preservatives".
Abstract: Tumor classification is a key area of research in the
field of bioinformatics. Microarray technology is commonly used in
the study of disease diagnosis using gene expression levels. The
main drawback of gene expression data is that it contains thousands
of genes and a very few samples. Feature selection methods are used
to select the informative genes from the microarray. These methods
considerably improve the classification accuracy. In the proposed
method, Genetic Algorithm (GA) is used for effective feature
selection. Informative genes are identified based on the T-Statistics,
Signal-to-Noise Ratio (SNR) and F-Test values. The initial candidate
solutions of GA are obtained from top-m informative genes. The
classification accuracy of k-Nearest Neighbor (kNN) method is used
as the fitness function for GA. In this work, kNN and Support Vector
Machine (SVM) are used as the classifiers. The experimental results
show that the proposed work is suitable for effective feature
selection. With the help of the selected genes, GA-kNN method
achieves 100% accuracy in 4 datasets and GA-SVM method
achieves in 5 out of 10 datasets. The GA with kNN and SVM
methods are demonstrated to be an accurate method for microarray
based tumor classification.
Abstract: COSMED K4b2 is a portable electrical device designed to test pulmonary functions. It is ideal for many applications that need the measurement of the cardio-respiratory response either in the field or in the lab is capable with the capability to delivery real time data to a sink node or a PC base station with storing data in the memory at the same time. But the actual sensor outputs and data received may contain some errors, such as impulsive noise which can be related to sensors, low batteries, environment or disturbance in data acquisition process. These abnormal outputs might cause misinterpretations of exercise or living activities to persons being monitored. In our paper we propose an effective and feasible method to detect and identify errors in applications by principal component analysis (PCA) and a back propagation (BP) neural network.
Abstract: Starting with an analysis of the financial and
operational indicators that can be found in the specialised literature,
this study aims to contribute to improvements in the performance
measurement systems used when the unit of analysis is the
manufacturing plant. For this a search was done in the highest impact
Journals of Production and Operations Management and
Management Accounting , with the aim of determining the financial
and operational indicators used to evaluate performance when
Advanced Production Practices have been implemented, more
specifically when the practices implemented are Total Quality
Management, JIT/Lean Manufacturing and Total Productive
Maintenance. This has enabled us to obtain a classification of the two
types of indicators based on how much each is used. For the financial
indicators we have also prepared a proposal that can be adapted to
manufacturing plants- accounting features. In the near future we will
propose a model that links practices implementation with financial
and operational indicators and these two last with each other. We aim
to will test this model empirically with the data obtained in the High
Performance Manufacturing Project.
Abstract: Simulation is a very powerful method used for highperformance
and high-quality design in distributed system, and now
maybe the only one, considering the heterogeneity, complexity and
cost of distributed systems. In Grid environments, foe example, it is
hard and even impossible to perform scheduler performance
evaluation in a repeatable and controllable manner as resources and
users are distributed across multiple organizations with their own
policies. In addition, Grid test-beds are limited and creating an
adequately-sized test-bed is expensive and time consuming.
Scalability, reliability and fault-tolerance become important
requirements for distributed systems in order to support distributed
computation. A distributed system with such characteristics is called
dependable. Large environments, like Cloud, offer unique
advantages, such as low cost, dependability and satisfy QoS for all
users. Resource management in large environments address
performant scheduling algorithm guided by QoS constrains. This
paper presents the performance evaluation of scheduling heuristics
guided by different optimization criteria. The algorithms for
distributed scheduling are analyzed in order to satisfy users
constrains considering in the same time independent capabilities of
resources. This analysis acts like a profiling step for algorithm
calibration. The performance evaluation is based on simulation. The
simulator is MONARC, a powerful tool for large scale distributed
systems simulation. The novelty of this paper consists in synthetic
analysis results that offer guidelines for scheduler service
configuration and sustain the empirical-based decision. The results
could be used in decisions regarding optimizations to existing Grid
DAG Scheduling and for selecting the proper algorithm for DAG
scheduling in various actual situations.
Abstract: It has become crucial over the years for nations to
improve their credit scoring methods and techniques in light of the
increasing volatility of the global economy. Statistical methods or
tools have been the favoured means for this; however artificial
intelligence or soft computing based techniques are becoming
increasingly preferred due to their proficient and precise nature and
relative simplicity. This work presents a comparison between Support
Vector Machines and Artificial Neural Networks two popular soft
computing models when applied to credit scoring. Amidst the
different criteria-s that can be used for comparisons; accuracy,
computational complexity and processing times are the selected
criteria used to evaluate both models. Furthermore the German credit
scoring dataset which is a real world dataset is used to train and test
both developed models. Experimental results obtained from our study
suggest that although both soft computing models could be used with
a high degree of accuracy, Artificial Neural Networks deliver better
results than Support Vector Machines.
Abstract: DG application has received increasing attention during
recent years. The impact of DG on various aspects of distribution system
operation, such as reliability and energy loss, depend highly on DG
location in distribution feeder. Optimal DG placement is an important
subject which has not been fully discussed yet.
This paper presents an optimization method to determine optimal DG
placement, based on a cost/worth analysis approach. This method
considers technical and economical factors such as energy loss, load point
reliability indices and DG costs, and particularly, portability of DG. The
proposed method is applied to a test system and the impacts of different
parameters such as load growth rate and load forecast uncertainty (LFU)
on optimum DG location are studied.
Abstract: In view of geological origin, formation of the shallow
gas reservoir of the Hangzhou Bay, northern Zhejiang Province,
eastern China, and original occurrence characteristics of the gassy
sand are analyzed. Generally, gassy sand in scale gas reservoirs is in
the state of residual moisture content and the approximate scope of
initial matric suction of sand ranges about from 0kPa to100kPa.
Results based on GDS triaxial tests show that the classical shear
strength formulas of unsaturated soil can not effectively describe basic
strength characteristics of gassy sand; the relationship between
apparent cohesion and matric suction of gassy sand agrees well with
the power function, which can reasonably be used to describe the
strength of gassy sand. In the stress path of gas release, shear strength
of gassy sand will increase and experimental results show the formula
proposed in this paper can effectively predict the strength increment.
When saturated strength indexes of the sand are used in engineering
design, moderate reduction should be considered.
Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: Measuring the complexity of software has been an
insoluble problem in software engineering. Complexity measures can
be used to predict critical information about testability, reliability,
and maintainability of software systems from automatic analysis of
the source code. During the past few years, many complexity
measures have been invented based on the emerging Cognitive
Informatics discipline. These software complexity measures,
including cognitive functional size, lend themselves to the approach
of the total cognitive weights of basic control structures such as loops
and branches. This paper shows that the current existing calculation
method can generate different results that are algebraically
equivalence. However, analysis of the combinatorial meanings of this
calculation method shows significant flaw of the measure, which also
explains why it does not satisfy Weyuker's properties. Based on the
findings, improvement directions, such as measures fusion, and
cumulative variable counting scheme are suggested to enhance the
effectiveness of cognitive complexity measures.
Abstract: Within the realm of e-government, the development has moved towards testing new means for democratic decisionmaking, like e-panels, electronic discussion forums, and polls. Although such new developments seem promising, they are not problem-free, and the outcomes are seldom used in the subsequent formal political procedures. Nevertheless, process models offer promising potential when it comes to structuring and supporting transparency of decision processes in order to facilitate the integration of the public into decision-making procedures in a reasonable and manageable way. Based on real-life cases of urban planning processes in Sweden, we present an outline for an integrated framework for public decision making to: a) provide tools for citizens to organize discussion and create opinions; b) enable governments, authorities, and institutions to better analyse these opinions; and c) enable governments to account for this information in planning and societal decision making by employing a process model for structured public decision making.
Abstract: Recommender Systems act as personalized decision
guides, aiding users in decisions on matters related to personal taste.
Most previous research on Recommender Systems has focused on the
statistical accuracy of the algorithms driving the systems, with no
emphasis on the trustworthiness of the user. RS depends on
information provided by different users to gather its knowledge. We
believe, if a large group of users provide wrong information it will
not be possible for the RS to arrive in an accurate conclusion. The
system described in this paper introduce the concept of Testing the
knowledge of user to filter out these “bad users".
This paper emphasizes on the mechanism used to provide robust
and effective recommendation.
Abstract: An intuitive user interface for the teleoperation of mobile rescue robots is one key feature for a successful exploration of inaccessible and no-go areas. Therefore, we have developed a novel framework to embed a flexible and modular user interface into a complete 3-D virtual reality simulation system. Our approach is based on a client-server architecture to allow for a collaborative control of the rescue robot together with multiple clients on demand. Further, it is important that the user interface is not restricted to any specific type of mobile robot. Therefore, our flexible approach allows for the operation of different robot types with a consistent concept and user interface. In laboratory tests, we have evaluated the validity and effectiveness of our approach with the help of two different robot platforms and several input devices. As a result, an untrained person can intuitively teleoperate both robots without needing a familiarization time when changing the operating robot.
Abstract: The intelligent fuzzy input estimator is used to estimate
the input force of the rigid bar structural system in this study. The
fuzzy Kalman filter without the input term and the fuzzy weighting
recursive least square estimator are two main portions of this method.
The practicability and accuracy of the proposed method were verified
with numerical simulations from which the input forces of a rigid bar
structural system were estimated from the output responses. In order to
examine the accuracy of the proposed method, a rigid bar structural
system is subjected to periodic sinusoidal dynamic loading. The
excellent performance of this estimator is demonstrated by comparing
it with the use of difference weighting function and improper the
initial process noise covariance. The estimated results have a good
agreement with the true values in all cases tested.