Abstract: The fuel cost of the motor vehicle operating on its
common route is an important part of the operating cost. Therefore,
the importance of the fuel saving is increasing day by day. One of the
parameters which improve fuel saving is the regulation of driving
characteristics. The number and duration of stop is increased by the
heavy traffic load. It is possible to improve the fuel saving with
regulation of traffic flow and driving characteristics. The researches
show that the regulation of the traffic flow decreases fuel
consumption, but it is not enough to improve fuel saving without the
regulation of driving characteristics. This study analyses the fuel
consumption of two trips of city bus operating on its common route
and determines the effect of traffic density and driving characteristics
on fuel consumption. Finally it offers some suggestions about
regulation of driving characteristics to improve the fuel saving. Fuel
saving is determined according to the results obtained from
simulation program. When experimental and simulation results are
compared, it has been found that the fuel saving was reached up the
to 40 percent ratios.
Abstract: Historic religious buildings located in seismic areas
have developed different failure mechanisms. Simulation of failure
modes is done with computer programs through a nonlinear dynamic
analysis or simplified using the method of failure blocks. Currently
there are simulation methodologies of failure modes based on the
failure rigid blocks method only for Roman Catholic churches type.
Due to differences of shape in plan, elevation and construction
systems between Orthodox churches and Catholic churches, for the
first time there were initiated researches in the development of this
simulation methodology for Orthodox churches. In this article are
presented the first results from the researches. The theoretical results
were compared with real failure modes recorded at an Orthodox
church from Banat region, severely damaged by earthquakes in
1991. Simulated seismic response, using a computer program based
on finite element method was confirmed by cracks after earthquakes.
The consolidation of the church was made according to these
theoretical results, realizing a rigid floor connecting all the failure
blocks.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: The main objective of Automatic Generation Control (AGC) is to balance the total system generation against system load losses so that the desired frequency and power interchange with neighboring systems is maintained. Any mismatch between generation and demand causes the system frequency to deviate from its nominal value. Thus high frequency deviation may lead to system collapse. This necessitates a very fast and accurate controller to maintain the nominal system frequency. This paper deals with a novel approach of artificial intelligence (AI) technique called Hybrid Neuro-Fuzzy (HNF) approach for an (AGC). The advantage of this controller is that it can handle the non-linearities at the same time it is faster than other conventional controllers. The effectiveness of the proposed controller in increasing the damping of local and inter area modes of oscillation is demonstrated in a two area interconnected power system. The result shows that intelligent controller is having improved dynamic response and at the same time faster than conventional controller.
Abstract: Coordinated supply chain represents major challenges
for the different actors involved in it, because each agent responds to
individual interests. The paper presents a framework with the
reviewed literature regarding the system's decision structure and
nature of demand. Later, it characterizes an agri food supply chain in
the Central Region of Colombia, it responds to a decentralized
distribution system and a stochastic demand. Finally, the paper
recommends coordinating the chain based on shared information, and
mechanisms for each agent, as VMI (vendor-managed inventory)
strategy for farmer-buyer relationship, information system for
farmers and contracts for transportation service providers.
Abstract: Many studies have focused on the nonlinear analysis
of electroencephalography (EEG) mainly for the characterization of
epileptic brain states. It is assumed that at least two states of the
epileptic brain are possible: the interictal state characterized by a
normal apparently random, steady-state EEG ongoing activity; and
the ictal state that is characterized by paroxysmal occurrence of
synchronous oscillations and is generally called in neurology, a
seizure.
The spatial and temporal dynamics of the epileptogenic process is
still not clear completely especially the most challenging aspects of
epileptology which is the anticipation of the seizure. Despite all the
efforts we still don-t know how and when and why the seizure
occurs. However actual studies bring strong evidence that the
interictal-ictal state transition is not an abrupt phenomena. Findings
also indicate that it is possible to detect a preseizure phase.
Our approach is to use the neural network tool to detect interictal
states and to predict from those states the upcoming seizure ( ictal
state). Analysis of the EEG signal based on neural networks is used
for the classification of EEG as either seizure or non-seizure. By
applying prediction methods it will be possible to predict the
upcoming seizure from non-seizure EEG.
We will study the patients admitted to the epilepsy monitoring
unit for the purpose of recording their seizures. Preictal, ictal, and
post ictal EEG recordings are available on such patients for analysis
The system will be induced by taking a body of samples then
validate it using another. Distinct from the two first ones a third body
of samples is taken to test the network for the achievement of
optimum prediction. Several methods will be tried 'Backpropagation
ANN' and 'RBF'.
Abstract: Petri Net (PN) has proven to be effective graphical, mathematical, simulation, and control tool for Discrete Event Systems (DES). But, with the growth in the complexity of modern industrial, and communication systems, PN found themselves inadequate to address the problems of uncertainty, and imprecision in data. This gave rise to amalgamation of Fuzzy logic with Petri nets and a new tool emerged with the name of Fuzzy Petri Nets (FPN). Although there had been a lot of research done on FPN and a number of their applications have been anticipated, but their basic types and structure are still ambiguous. Therefore, in this research, an effort is made to categorize FPN according to their structure and algorithms Further, literature review of the applications of FPN in the light of their classifications has been done.
Abstract: The paper presents the potential for RES in Romania
and the results of the Romanian national research project “Romania
contribution to the European targets regarding the development of
renewable energy sources - PROMES". The objective of the project
is the development of energy generation from renewable energy
sources (RES) in Romania by drawing up scenarios and prognosis
harmonized with national and European targets, RES development
effects modeling (environmental, economic, social etc.), research of
the impact of the penetration of RES into the main, implementation
of an advanced software system tool for RES information recording
and communication, experimental research based on demonstrative
applications.
The expected results are briefly presented, as well as the social,
economic and environmental impact.
Abstract: Petrol Fuel Station (PFS) has potential hazards to the
people, asset, environment and reputation of an operating company.
Fire hazards, static electricity air pollution evoked by aliphatic and
aromatic organic compounds are major causes of accident/incident
occurrence at fuel station. Activities such as carelessness,
maintenance, housekeeping, slips trips and falls, transportation
hazard, major and minor injuries, robbery and snake bites has a
potential to create unsafe conditions. The level of risk of these
hazards varies according to location and country. The emphasis on
safety considerations by the government is variable all around the
world. Developed countries safety records are much better as
compared to developing countries safety statistics. There is no
significant approach available to highlight the unsafe acts and unsafe
conditions during operation and maintenance of fuel station. Fuel
station is the most commonly available facilities that contain
flammable and hazardous materials. Due to continuous operation of
fuel station they pose various hazards to people, environment and
assets of an organization. To control these hazards, there is a need for
specific approach. PFS operation is unique as compared to other
businesses. For smooth operations it demands an involvement of
operating company, contractor and operator group. This study will
focus to address hazard contributing factors that have a potential to
make PFS operation risky. One year data collected, 902 activities
analyzed, comparisons were made to highlight significant
contributing factors. The study will provide help and assistance to
PFS outlet marketing companies to make their fuel station operation
safer. It will help health safety and environment (HSE) professionals
to arrest the gap available related to safety matters at PFS.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: Perennial ryegrass (Lolium perenne L.) plants are cultivated for lawn constitution and as forage plants. Considerable number of perennial ryegrass genotypes are present in the flora of our country and they present substantial was performed based on a Project supported bu TUBITAK (Project numver : 106O159) and perannial ryegrass genotypes from 8 provinces were collected during 2006. Seeds of perennial ryegrass were collected from 48 different locations. Populations of turfgrass seeds in flowerpots to be 20 and 1 cm deep greenhouse were sown in three replications at 07.07.2007.Then the growth of turfgrass seedlings in the greenhouse in pots showed sufficiently separated from the plants were planted in each population. Plants planted in the garden of the observation scale of 1-9 was evaluated by the quality, 1 = the weakest / worst, 6 = acceptable and 9 = superior or considered as an ideal. Essentially only recognized in assessing the quality of the color of grass, but the color, density, uniformity, texture (texture), illness or environmental stresses are evaluated as a combination reaction. Turfgrass quality 15.11.2007, 19.03.2008, 27.05.2008, 27.11.2008, 07.03.2009 and 02.06.2009 have been 6 times to be in order. Observations made regarding the quality of grass; 3 years according to seasonal environments turf quality genotypes belonging to 14 different populations were found to be 7.5 and above are reserved for future use in breeding works.The number of genotypes belonging to 41 populations in terms of turfgrass quality was determined as 7.9 of 3 year average seasonal. Argıthan between Doğanhisar (Konya) is located 38.09 latitude and 31.40 longitude, altitude 1158 m in the set that population numbered 41.
Abstract: Using spatial models as a shared common basis of
information about the environment for different kinds of contextaware
systems has been a heavily researched topic in the last years.
Thereby the research focused on how to create, to update, and to
merge spatial models so as to enable highly dynamic, consistent and
coherent spatial models at large scale. In this paper however, we
want to concentrate on how context-aware applications could use this
information so as to adapt their behavior according to the situation
they are in. The main idea is to provide the spatial model
infrastructure with a situation recognition component based on
generic situation templates. A situation template is – as part of a
much larger situation template library – an abstract, machinereadable
description of a certain basic situation type, which could be
used by different applications to evaluate their situation. In this
paper, different theoretical and practical issues – technical, ethical
and philosophical ones – are discussed important for understanding
and developing situation dependent systems based on situation
templates. A basic system design is presented which allows for the
reasoning with uncertain data using an improved version of a
learning algorithm for the automatic adaption of situation templates.
Finally, for supporting the development of adaptive applications, we
present a new situation-aware adaptation concept based on
workflows.
Abstract: Nowadays the control of stator voltage at a constant frequency is one of the traditional and low expense methods in order to control the speed of induction motors near its nominal speed. The torque of induction motor is a nonlinear function of the firing angle, phase angle and speed. In this paper the speed control of induction motor regarding various load torque and under different conditions will be investigated based on a fuzzy controller with inverse training.
Abstract: The identification and elimination of bad
measurements is one of the basic functions of a robust state estimator
as bad data have the effect of corrupting the results of state
estimation according to the popular weighted least squares method.
However this is a difficult problem to handle especially when dealing
with multiple errors from the interactive conforming type. In this
paper, a self adaptive genetic based algorithm is proposed. The
algorithm utilizes the results of the classical linearized normal
residuals approach to tune the genetic operators thus instead of
making a randomized search throughout the whole search space it is
more likely to be a directed search thus the optimum solution is
obtained at very early stages(maximum of 5 generations). The
algorithm utilizes the accumulating databases of already computed
cases to reduce the computational burden to minimum. Tests are
conducted with reference to the standard IEEE test systems. Test
results are very promising.
Abstract: Protection and proper management of archaeological heritage are an essential process of studying and interpreting the generations present and future. Protecting the archaeological heritage is based upon multidiscipline professional collaboration. This study aims to gather data by different sources (Photogrammetry and Geographic Information System (GIS)) integrated for the purpose of documenting one the of significant archeological sites (Ahl-Alkahf, Jordan). 3D modeling deals with the actual image of the features, shapes and texture to represent reality as realistically as possible by using texture. The 3D coordinates that result of the photogrammetric adjustment procedures are used to create 3D-models of the study area. Adding Textures to the 3D-models surfaces gives a 'real world' appearance to the displayed models. GIS system combined all data, including boundary maps, indicating the location of archeological sites, transportation layer, digital elevation model and orthoimages. For realistic representation of the study area, 3D - GIS model prepared, where efficient generation, management and visualization of such special data can be achieved.
Abstract: Electromyography (EMG) is the study of muscles function through analysis of electrical activity produced from muscles. This electrical activity which is displayed in the form of signal is the result of neuromuscular activation associated with muscle contraction. The most common techniques of EMG signal recording are by using surface and needle/wire electrode where the latter is usually used for interest in deep muscle. This paper will focus on surface electromyogram (SEMG) signal. During SEMG recording, several problems had to been countered such as noise, motion artifact and signal instability. Thus, various signal processing techniques had been implemented to produce a reliable signal for analysis. SEMG signal finds broad application particularly in biomedical field. It had been analyzed and studied for various interests such as neuromuscular disease, enhancement of muscular function and human-computer interface.
Abstract: In this paper we consider a one-dimensional random
geometric graph process with the inter-nodal gaps evolving according
to an exponential AR(1) process. The transition probability matrix
and stationary distribution are derived for the Markov chains concerning
connectivity and the number of components. We analyze the
algorithm for hitting time regarding disconnectivity. In addition to
dynamical properties, we also study topological properties for static
snapshots. We obtain the degree distributions as well as asymptotic
precise bounds and strong law of large numbers for connectivity
threshold distance and the largest nearest neighbor distance amongst
others. Both exact results and limit theorems are provided in this
paper.
Abstract: The main purpose of this research is the calculation of implicit prices of the environmental level of air quality in the city of Moscow on the basis of housing property prices. The database used contains records of approximately 20 thousand apartments and has been provided by a leading real estate agency operating in Russia. The explanatory variables include physical characteristics of the houses, environmental (industry emissions), neighbourhood sociodemographic and geographic data: GPS coordinates of each house. The hedonic regression results for ecological variables show «negative» prices while increasing the level of air contamination from such substances as carbon monoxide, nitrogen dioxide, sulphur dioxide, and particles (CO, NO2, SO2, TSP). The marginal willingness to pay for higher environmental quality is presented for linear and log-log models.
Abstract: Mapping between local and global coordinates is an
important issue in finite element method, as all calculations are
performed in local coordinates. The concern arises when subparametric
are used, in which the shape functions of the field variable
and the geometry of the element are not the same. This is particularly
the case for C* elements in which the extra degrees of freedoms
added to the nodes make the elements sub-parametric. In the present
work, transformation matrix for C1* (an 8-noded hexahedron
element with 12 degrees of freedom at each node) is obtained using
equivalent C0 elements (with the same number of degrees of
freedom). The convergence rate of 8-noded C1* element is nearly
equal to its equivalent C0 element, while it consumes less CPU time
with respect to the C0 element. The existence of derivative degrees
of freedom at the nodes of C1* element along with excellent
convergence makes it superior compared with it equivalent C0
element.