Abstract: Asynchronous Transfer Mode (ATM) is widely used
in telecommunications systems to send data, video and voice at a
very high speed. In ATM network optimizing the bandwidth through
dynamic routing is an important consideration. Previous research
work shows that traditional optimization heuristics result in suboptimal
solution. In this paper we have explored non-traditional
optimization technique. We propose comparison of two such
algorithms - Genetic Algorithm (GA) and Tabu search (TS), based on
non-traditional Optimization approach, for solving the dynamic
routing problem in ATM networks which in return will optimize the
bandwidth. The optimized bandwidth could mean that some
attractive business applications would become feasible such as high
speed LAN interconnection, teleconferencing etc. We have also
performed a comparative study of the selection mechanisms in GA
and listed the best selection mechanism and a new initialization
technique which improves the efficiency of the GA.
Abstract: This paper describes interconnection between
technical and economical making decision. The reason of this dealing
could be different: poor technical condition, change of substation
(electrical network) regime, power transformer owner budget deficit
and increasing of tariff on electricity. Establishing of recommended
practice as well as to give general advice and guidance in economical
sector, testing, diagnostic power transformers to establish its
conditions, identify problems and provide potential remedies.
Abstract: The various applications of VLSI circuits in highperformance
computing, telecommunications, and consumer
electronics has been expanding progressively, and at a very hasty
pace. This paper describes a new model for partitioning a circuit
using DBSCAN and fuzzy ARTMAP neural network. The first step
is concerned with feature extraction, where we had make use
DBSCAN algorithm. The second step is the classification and is
composed of a fuzzy ARTMAP neural network. The performance of
both approaches is compared using benchmark data provided by
MCNC standard cell placement benchmark netlists. Analysis of the
investigational results proved that the fuzzy ARTMAP with
DBSCAN model achieves greater performance then only fuzzy
ARTMAP in recognizing sub-circuits with lowest amount of
interconnections between them The recognition rate using fuzzy
ARTMAP with DBSCAN is 97.7% compared to only fuzzy
ARTMAP.
Abstract: In this study rack systems that are structural storage
units of warehouses have been analyzed as structural with Finite
Element Method (FEA). Each cell of discussed rack system storages
pallets which have from 800 kg to 1000 kg weights and
0.80x1.15x1.50 m dimensions. Under this load, total deformations
and equivalent stresses of structural elements and principal stresses,
tensile stresses and shear stresses of connection elements have been
analyzed. The results of analyses have been evaluated according to
resistance limits of structural and connection elements. Obtained
results have been presented as visual and magnitude.
Abstract: This paper presents an equivalent circuit model based on piecewise linear parallel branches (PLPB) to study solar cell modules which are partially shaded. The PLPB model can easily be used in circuit simulation software such as the ElectroMagnetic Transients Program (EMTP). This PLPB model allows the user to simulate several different configurations of solar cells, the influence of partial shadowing on a single or multiple cells, the influence of the number of solar cells protected by a bypass diode and the effect of the cell connection configuration on partial shadowing.
Abstract: For several high speed networks, providing resilience against failures is an essential requirement. The main feature for designing next generation optical networks is protecting and restoring high capacity WDM networks from the failures. Quick detection, identification and restoration make networks more strong and consistent even though the failures cannot be avoided. Hence, it is necessary to develop fast, efficient and dependable fault localization or detection mechanisms. In this paper we propose a new fault localization algorithm for WDM networks which can identify the location of a failure on a failed lightpath. Our algorithm detects the failed connection and then attempts to reroute data stream through an alternate path. In addition to this, we develop an algorithm to analyze the information of the alarms generated by the components of an optical network, in the presence of a fault. It uses the alarm correlation in order to reduce the list of suspected components shown to the network operators. By our simulation results, we show that our proposed algorithms achieve less blocking probability and delay while getting higher throughput.
Abstract: In the last years, the computers have increased their capacity of calculus and networks, for the interconnection of these machines. The networks have been improved until obtaining the actual high rates of data transferring. The programs that nowadays try to take advantage of these new technologies cannot be written using the traditional techniques of programming, since most of the algorithms were designed for being executed in an only processor,in a nonconcurrent form instead of being executed concurrently ina set of processors working and communicating through a network.This paper aims to present the ongoing development of a new system for the reconfiguration of grouping of computers, taking into account these new technologies.
Abstract: The article aims to investigate the presence of a correlation between eco-innovation and economic performance within industrial districts. The case analyzed in this article is based on a study concerning a sample of 54 Italian industrial clusters entitled "Eco-Districts" that has compiled a list of the most eco-efficient districts at the national level. After selecting two districts, this study assesses the economic performance of the last three years through the analysis of trends in four indicators. The results show that only in some cases there is a connection between eco innovation and economic performance.
Abstract: This paper aims at improving web server performance
by establishing a middleware layer between web and database
servers, which minimizes the overload on the database server. A
middleware system has been developed as a service mainly to
improve the performance. This system manages connection accesses
in a way that would result in reducing the overload on the database
server. In addition to the connection management, this system acts as
an object-oriented model for best utilization of operating system
resources. A web developer can use this Service Broker to improve
web server performance.
Abstract: Development of knowledge based society carries multiple challenges to the higher education system. Some of the challenges laid before the higher education sector of countries which aspire to become knowledge based societies are: the entrepreneurial leadership of the higher education institutions, finding new sources of financing in order to minimize dependence on public resources, creating connections with the labor market, commercial utilization of R&D results, promotion of innovations as well as the overall promotion of science excellence relevant to the economic sector. Within a framework of this paper and its main subject of research, the challenge which is being put before the higher education institutions is an effort of establishing regional mission of higher education through the open collaboration with regional key factors, both private and public. Development of the mentioned collaboration and its contribution to the overall regional development in Croatia is the main subject of empirical research in this paper.
Abstract: The growth and interconnection of power networks in many regions has invited complicated techniques for energy management services (EMS). State estimation techniques become a powerful tool in power system control centers, and that more information is required to achieve the objective of EMS. For the online state estimator, assuming the continuous time is equidistantly sampled with period Δt, processing events must be finished within this period. Advantage of Kalman Filtering (KF) algorithm in using system information to improve the estimation precision is utilized. Computational power is a major issue responsible for the achievement of the objective, i.e. estimators- solution at a small sampled period. This paper presents the optimum utilization of processors in a state estimator based on KF. The model used is presented using Petri net (PN) theory.
Abstract: In the last couple of years Bluetooth has gained a large share in the market of home and personal appliances. It is now a well established technology a short range supplement to the wireless world of 802.11. The two main trends of research that have sprung from these developments are directed towards the coexistence and performance issues of Bluetooth and 802.11 as well as the co-existence in the very short range of multiple Bluetooth devices. Our work aims at thoroughly investigating different aspects of co-channel interference and effects of transmission power, distance and 802.11 interference on Bluetooth connections.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: In construction of any structure, the aesthetic and utility values should be considered in such a way as to make the structure cost-effective. Most structures are composed of elements and joints which are very critical in any skeletal space structure because they majorly determine the performance of the structure. In early times, most space structures were constructed using rigid joints which had the advantage of better performing structures as compared to pin-jointed structures but with the disadvantage of requiring all the construction work to be done on site. The discovery of semi-rigid joints now enables connections to be prefabricated and quickly assembled on site while maintaining good performance. In this paper, cost-effective is discussed basing on strength of connectors at the joints, buckling of joints and overall structure, and the effect of initial geometrical imperfections. Several existing joints are reviewed by classifying them into categories and discussing where they are most suited and how they perform structurally. Also, finite element modeling using ABAQUS is done to determine the buckling behavior. It is observed that some joints are more economical than others. The rise to span ratio and imperfections are also found to affect the buckling of the structures. Based on these, general principles that guide the design of cost-effective joints and structures are discussed.
Abstract: Pregnancy is considered a special period in a woman’s life. There are myths about pregnancy that describe gender predictions, dietary beliefs, pregnancy signs, and risk of magic or witchcraft. Majority of these myths is in connection with the early childcare. In traditional societies midwives and experienced women practice and teach these myths to young mothers. Mother who feel special and vulnerable, at the same time feel secure in following these socially transmitted myths. Rural Punjab, a province of Pakistan has a culture rich with beliefs and myths. Myths about pregnancy are significant in rural culture and pregnancy care is seen as mother and childcare. This paper presents my research reflections that I did as a part of my Ph.D studies about early childcare beliefs and rituals practiced in rural Punjab, Pakistan.
Abstract: In this paper, based on the work in [1], we further give
a general model for acquiring knowledge, which first focuses on the
research of how and when things involved in problems are made
then describes the goals, the energy and the time to give an optimum
model to decide how many related things are supposed to be involved
in. Finally, we acquire knowledge from this model in which there are
the attributes, actions and connections of the things involved at the
time when they are born and the time in their life. This model not
only improves AI theories, but also surely brings the effectiveness
and accuracy for AI system because systems are given more
knowledge when reasoning or computing is used to bring about
results.
Abstract: Truncated multiplier is a good candidate for digital
signal processing (DSP) applications including finite impulse
response (FIR) and discrete cosine transform (DCT). Through
truncated multiplier a significant reduction in Field Programmable
Gate Array (FPGA) resources can be achieved. This paper presents
for the first time a comparison of resource utilization of Spartan-3AN
and Virtex-5 implementation of standard and truncated multipliers
using Very High Speed Integrated Circuit Hardware Description
Language (VHDL). The Virtex-5 FPGA shows significant
improvement as compared to Spartan-3AN FPGA device. The
Virtex-5 FPGA device shows better performance with a percentage
ratio of number of occupied slices for standard to truncated
multipliers is increased from 40% to 73.86% as compared to Spartan-
3AN is decreased from 68.75% to 58.78%. Results show that the
anomaly in Spartan-3AN FPGA device average connection and
maximum pin delay have been efficiently reduced in Virtex-5 FPGA
device.
Abstract: Adopting the measured constitutive relationship of
stress-strain of river ice, the finite element analysis model of
percussive force of river ice and pier is established, by the explicit
dynamical analysis software package LS-DYNA. Effects of element
types, contact method and arithmetic of ice and pier, coupled modes
between different elements, mesh density of pier, and ice sheet in
contact area on the collision force are studied. Some of measures for
the collision force analysis of river ice and pier are proposed as
follows: bridge girder can adopt beam161 element with 3-node; pier
below the line of 1.30m above ice surface and ice sheet use solid164
element with 8-node; in order to accomplish the connection of
different elements, the rigid body with 0.01-0.05m thickness is defined
between solid164 and beam161; the contact type of ice and pier adopts
AUTOMATIC_SURFACE_TO_SURFACE, using symmetrical
penalty function algorithms; meshing size of pier below the line of
1.30m above ice surface should not less than 0.25×0.25×0.5m3. The
simulation results have the advantage of high precision by making a
comparison between measured and computed data. The research
results can be referred for collision force study between river ice and
pier.
Abstract: In this article we explore how computer assisted exercises may allow for bridging the traditional gap between theory and practice in professional education. To educate officers able to master the complexity of the battlefield the Norwegian Military Academy needs to develop a learning environment that allows for creating viable connections between the educational environment and the field of practice. In response to this challenge we explore the conditions necessary to make computer assisted training systems (CATS) a useful tool to create structural similarities between an educational context and the field of military practice. Although, CATS may facilitate work procedures close to real life situations, this case do demonstrate how professional competence also must build on viable learning theories and environments. This paper explores the conditions that allow for using simulators to facilitate professional competence from within an educational setting. We develop a generic didactic model that ascribes learning to participation in iterative cycles of action and reflection. The development of this model is motivated by the need to develop an interdisciplinary professional education rooted in the pattern of military practice.
Abstract: Anchovy (Engraulis Encrasicholus) and sardine
(Sardina Pilchardus) are blue fishes linked to our alimentary tradition
of Mediterranean. In our work, particularly, we tested for the first
time physical and enzymatic methods to verify the freshness of
species of blue fish, anchovy and sardine of Mediterranean. In
connection with to the lowering of the pH after post-mortem stage we
assisted to a increase in proteolytic activity of calpaine and catpsine.
Already after 2 h in post-mortem there was a significant increase.