Abstract: The increasing demand for higher data rates in wireless communication systems has led to the more effective and efficient use of all allocated frequency bands. In order to use the whole bandwidth at maximum efficiency, one needs to have RF power amplifiers with a higher linear level and memory-less performance. This is considered to be a major challenge to circuit designers. In this thesis the linearity and memory are studied and examined via the behavior of the intermodulation distortion (IMD). A major source of the in-band distortion can be shown to be influenced by the out-of-band impedances presented at either the input or the output of the device, especially those impedances terminated the low frequency (IF) components. Thus, in order to regulate the in-band distortion, the out of-band distortion must be controllable. These investigations are performed on a 12W LDMOS device characterised at 2.1 GHz within a purpose built, high-power measurement system.
Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: Knowing about the customer behavior in a grocery has
been a long-standing issue in the retailing industry. The advent of
RFID has made it easier to collect moving data for an individual
shopper's behavior. Most of the previous studies used the traditional
statistical clustering technique to find the major characteristics of
customer behavior, especially shopping path. However, in using the
clustering technique, due to various spatial constraints in the store,
standard clustering methods are not feasible because moving data such
as the shopping path should be adjusted in advance of the analysis,
which is time-consuming and causes data distortion. To alleviate this
problem, we propose a new approach to spatial pattern clustering
based on the longest common subsequence. Experimental results using
real data obtained from a grocery confirm the good performance of the
proposed method in finding the hot spot, dead spot and major path
patterns of customer movements.
Abstract: Data security in u-Health system can be an important
issue because wireless network is vulnerable to hacking. However, it is
not easy to implement a proper security algorithm in an embedded
u-health monitoring because of hardware constraints such as low
performance, power consumption and limited memory size and etc. To
secure data that contain personal and biosignal information, we
implemented several security algorithms such as Blowfish, data
encryption standard (DES), advanced encryption standard (AES) and
Rivest Cipher 4 (RC4) for our u-Health monitoring system and the
results were successful. Under the same experimental conditions, we
compared these algorithms. RC4 had the fastest execution time.
Memory usage was the most efficient for DES. However, considering
performance and safety capability, however, we concluded that AES
was the most appropriate algorithm for a personal u-Health monitoring
system.
Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: This paper introduces two decoders for binary linear
codes based on Metaheuristics. The first one uses a genetic algorithm
and the second is based on a combination genetic algorithm with
a feed forward neural network. The decoder based on the genetic
algorithms (DAG) applied to BCH and convolutional codes give good
performances compared to Chase-2 and Viterbi algorithm respectively
and reach the performances of the OSD-3 for some Residue
Quadratic (RQ) codes. This algorithm is less complex for linear
block codes of large block length; furthermore their performances
can be improved by tuning the decoder-s parameters, in particular the
number of individuals by population and the number of generations.
In the second algorithm, the search space, in contrast to DAG which
was limited to the code word space, now covers the whole binary
vector space. It tries to elude a great number of coding operations
by using a neural network. This reduces greatly the complexity of
the decoder while maintaining comparable performances.
Abstract: The interactions between input/output variables are a very common phenomenon encountered in the design of multi-loop controllers for interacting multivariable processes, which can be a serious obstacle for achieving a good overall performance of multiloop control system. To overcome this impediment, the decomposed dynamic interaction analysis is proposed by decomposing the multiloop control system into a set of n independent SISO systems with the corresponding effective open-loop transfer function (EOTF) within the dynamic interactions embedded explicitly. For each EOTF, the reduced model is independently formulated by using the proposed reduction design strategy, and then the paired multi-loop proportional-integral-derivative (PID) controller is derived quite simply and straightforwardly by using internal model control (IMC) theory. This design method can easily be implemented for various industrial processes because of its effectiveness. Several case studies are considered to demonstrate the superior of the proposed method.
Abstract: Globalization and therefore increasing tight competition among companies, have resulted to increase the importance of making well-timed decision. Devising and employing effective strategies, that are flexible and adaptive to changing market, stand a greater chance of being effective in the long-term. In other side, a clear focus on managing the entire product lifecycle has emerged as critical areas for investment. Therefore, applying wellorganized tools to employ past experience in new case, helps to make proper and managerial decisions. Case based reasoning (CBR) is based on a means of solving a new problem by using or adapting solutions to old problems. In this paper, an adapted CBR model with k-nearest neighbor (K-NN) is employed to provide suggestions for better decision making which are adopted for a given product in the middle of life phase. The set of solutions are weighted by CBR in the principle of group decision making. Wrapper approach of genetic algorithm is employed to generate optimal feature subsets. The dataset of the department store, including various products which are collected among two years, have been used. K-fold approach is used to evaluate the classification accuracy rate. Empirical results are compared with classical case based reasoning algorithm which has no special process for feature selection, CBR-PCA algorithm based on filter approach feature selection, and Artificial Neural Network. The results indicate that the predictive performance of the model, compare with two CBR algorithms, in specific case is more effective.
Abstract: management of medical devices in hospitals includes
the planning of medical equipment acquisition and maintenance. The
presence of critical and non-critical areas together with technological
proliferation render the management of medical devices very
complex. This study creates an easy and objective methodology for
the analysis of medical equipment maintenance, that makes the
management of medical devices more feasible. The study has been
carried out at Florence Hospital Careggi and it aims to help the
clinical engineering department to manage medical equipment by
clarifying the hospital situation through a characterization of the
different areas, technologies and fault typologies.
Abstract: The intrusion detection problem has been frequently studied, but intrusion detection methods are often based on a single point of view, which always limits the results. In this paper, we introduce a new intrusion detection model based on the combination of different current methods. First we use a notion of distance to unify the different methods. Second we combine these methods using the Pearson correlation coefficients, which measure the relationship between two methods, and we obtain a combined distance. If the combined distance is greater than a predetermined threshold, an intrusion is detected. We have implemented and tested the combination model with two different public data sets: the data set of masquerade detection collected by Schonlau & al., and the data set of program behaviors from the University of New Mexico. The results of the experiments prove that the combination model has better performances.
Abstract: In this paper, stabilization of an Active Magnetic Bearing (AMB) system with varying rotor speed using Sliding Mode Control (SMC) technique is considered. The gyroscopic effect inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Also, transformation of the AMB dynamic model into a new class of uncertain system shows that this gyroscopic effect lies in the mismatched part of the system matrix. Moreover, the current gain parameter is allowed to be varied in a known bound as an uncertainty in the input matrix. SMC design method is proposed in which the sufficient condition that guarantees the global exponential stability of the reduced-order system is represented in Linear Matrix Inequality (LMI). Then, a new chattering-free control law is established such that the system states are driven to reach the switching surface and stay on it thereafter. The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: Ground-source heat pumps achieve higher efficiencies
than conventional air-source heat pumps because they exchange heat
with the ground that is cooler in summer and hotter in winter than the
air environment. Earth heat exchangers are essential parts of the
ground-source heat pumps and the accurate prediction of their
performance is of fundamental importance. This paper presents the
development and validation of a numerical model through an
incompressible fluid flow, for the simulation of energy and
temperature changes in and around a U-tube borehole heat
exchanger. The FlexPDE software is used to solve the resulting
simultaneous equations that model the heat exchanger. The validated
model (through a comparison with experimental data) is then used to
extract conclusions on how various parameters like the U-tube
diameter, the variation of the ground thermal conductivity and
specific heat and the borehole filling material affect the temperature
of the fluid.
Abstract: With the necessity of increased processing capacity with less energy consumption; power aware multiprocessor system has gained more attention in the recent future. One of the additional challenges that is to be solved in a multi-processor system when compared to uni-processor system is job allocation. This paper presents a novel task dependent job allocation algorithm: Energy centric- Allocation (Ec-A) and Rate Monotonic (RM) scheduling to minimize energy consumption in a multiprocessor system. A simulation analysis is carried out to verify the performance increase with reduction in energy consumption and required number of processors in the system.
Abstract: A cart-ball system is a challenging system from the
control engineering point of view. This is due to the nonlinearities,
multivariable, and non-minimum phase behavior present in this
system. This paper is concerned with the problem of modeling and
control of such system. The objective of control strategy is to place
the cart at a desired position while balancing the ball on the top of the
arc-shaped track fixed on the cart. A State-Feedback Controller
(SFC) with a pole-placement method will be designed in order to
control the system. At first, the mathematical model of a cart-ball
system in the state-space form is developed. Then, the linearization of
a model will be established in order to design a SFC. The integral
control strategy will be performed as to control the cart position of a
system. Simulation work is then performed using
MATLAB/SIMULINK software in order to study the performance of
SFC when applied to the system.
Abstract: The cables in a nuclear power plant are designed to be
used for about 40 years in safe operation environment. However, the
heat and radiation in the nuclear power plant causes the rapid
performance deterioration of cables in nuclear vessels and heat
exchangers, which requires cable lifetime estimation. The most
accurate method of estimating the cable lifetime is to evaluate the
cables in a laboratory. However, removing cables while the plant is
operating is not allowed because of its safety and cost. In this paper, a
robot system to estimate the cable lifetime in nuclear power plants is
developed and tested. The developed robot system can calculate a
modulus value to estimate the cable lifetime even when the nuclear
power plant is in operation.
Abstract: Network security attacks are the violation of
information security policy that received much attention to the
computational intelligence society in the last decades. Data mining
has become a very useful technique for detecting network intrusions
by extracting useful knowledge from large number of network data
or logs. Naïve Bayesian classifier is one of the most popular data
mining algorithm for classification, which provides an optimal way
to predict the class of an unknown example. It has been tested that
one set of probability derived from data is not good enough to have
good classification rate. In this paper, we proposed a new learning
algorithm for mining network logs to detect network intrusions
through naïve Bayesian classifier, which first clusters the network
logs into several groups based on similarity of logs, and then
calculates the prior and conditional probabilities for each group of
logs. For classifying a new log, the algorithm checks in which cluster
the log belongs and then use that cluster-s probability set to classify
the new log. We tested the performance of our proposed algorithm by
employing KDD99 benchmark network intrusion detection dataset,
and the experimental results proved that it improves detection rates
as well as reduces false positives for different types of network
intrusions.
Abstract: Classifying biomedical literature is a difficult and
challenging task, especially when a large number of biomedical
articles should be organized into a hierarchical structure. In this paper,
we present an approach for classifying a collection of biomedical text
abstracts downloaded from Medline database with the help of
ontology alignment. To accomplish our goal, we construct two types
of hierarchies, the OHSUMED disease hierarchy and the Medline
abstract disease hierarchies from the OHSUMED dataset and the
Medline abstracts, respectively. Then, we enrich the OHSUMED
disease hierarchy before adapting it to ontology alignment process for
finding probable concepts or categories. Subsequently, we compute
the cosine similarity between the vector in probable concepts (in the
“enriched" OHSUMED disease hierarchy) and the vector in Medline
abstract disease hierarchies. Finally, we assign category to the new
Medline abstracts based on the similarity score. The results obtained
from the experiments show the performance of our proposed approach
for hierarchical classification is slightly better than the performance of
the multi-class flat classification.
Abstract: In an era of knowledge explosion, the growth of data
increases rapidly day by day. Since data storage is a limited resource,
how to reduce the data space in the process becomes a challenge issue.
Data compression provides a good solution which can lower the
required space. Data mining has many useful applications in recent
years because it can help users discover interesting knowledge in large
databases. However, existing compression algorithms are not
appropriate for data mining. In [1, 2], two different approaches were
proposed to compress databases and then perform the data mining
process. However, they all lack the ability to decompress the data to
their original state and improve the data mining performance. In this
research a new approach called Mining Merged Transactions with the
Quantification Table (M2TQT) was proposed to solve these problems.
M2TQT uses the relationship of transactions to merge related
transactions and builds a quantification table to prune the candidate
itemsets which are impossible to become frequent in order to improve
the performance of mining association rules. The experiments show
that M2TQT performs better than existing approaches.
Abstract: In this paper, we propose a novel algorithm for
delineating the endocardial wall from a human heart ultrasound scan.
We assume that the gray levels in the ultrasound images are
independent and identically distributed random variables with
different Rician Inverse Gaussian (RiIG) distributions. Both synthetic
and real clinical data will be used for testing the algorithm. Algorithm
performance will be evaluated using the expert radiologist evaluation
of a soft copy of an ultrasound scan during the scanning process and
secondly, doctor’s conclusion after going through a printed copy of
the same scan. Successful implementation of this algorithm should
make it possible to differentiate normal from abnormal soft tissue and
help disease identification, what stage the disease is in and how best
to treat the patient. We hope that an automated system that uses this
algorithm will be useful in public hospitals especially in Third World
countries where problems such as shortage of skilled radiologists and
shortage of ultrasound machines are common. These public hospitals
are usually the first and last stop for most patients in these countries.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.