Abstract: Some of the polycyclic aromatic hydrocarbons (PAHs)
are the strongest known carcinogens compounds; the majority of
them are mostly produced by the incomplete combustion of fossil
fuels; Motor vehicles are a significant source of polycyclic aromatic
hydrocarbon (PAH) where diesel emission is one of the main sources
of such compounds available in the ambient air. There is a big
concern about the increasing concentration of PAHs in the
environment. Researchers are trying to explore optimal methods to
reduce those pollutants and improve the quality of air. Water blended
fuel is one of the possible approaches to reduce emission of PAHs
from the combustion of diesel in urban and domestic vehicles. In this
work a modeling study was conducted using CHEMKIN-PRO
software to simulate spray combustion at similar diesel engine
conditions. Surrogate fuel of (80 % n-heptane and 20 % toluene) was
used due to detailed kinetic and thermodynamic data needed for
modeling is available for this kind of fuel but not available for diesel.
An emulsified fuel with 3, 5, 8, 10 and 20 % water by volume is used
as an engine feed for this study. The modeling results show that water
has a significant effect on reducing engine soot and PAHs precursors
formation up to certain extent.
Abstract: A brushless DC motor with integrated drive circuit for air management system is presented. Using magnetic equivalent circuit model a basic design of the motor is determined, and specific configurations are inspected thanks to finite element analysis. In order to reduce an unbalanced magnetic force in an axial direction, induced forces between a stator core and a permanent magnet are calculated with respect to the relative positions of them. For the high efficiency, and high power density, BLDC motor and drive are developed. Also vibration mode and eccentricity of a rotor are considered at the rated and maximum rotational speed Through the experimental results, a validity of the simulated one is confirmed.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: Relay based communication has gained considerable importance in the recent years. In this paper we find the end-toend statistics of a two hop non-regenerative relay branch, each hop being Nakagami-m faded. Closed form expressions for the probability density functions of the signal envelope at the output of a selection combiner and a maximal ratio combiner at the destination node are also derived and analytical formulations are verified through computer simulation. These density functions are useful in evaluating the system performance in terms of bit error rate and outage probability.
Abstract: Cardiovascular disease mostly in the form of atherosclerosis is responsible for 30% of all world deaths amounting to 17 million people per year. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis. The initiation and progression of the disease is strongly linked to the hemodynamic environment near the vessel wall. The aim of this study is to validate the flow of blood mimic through an arterial stenosis model with computational fluid dynamics (CFD) package. In experiment, an axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. Particle image velocimetry (PIV) was used to characterize the flow. The fluid consists of rigid spherical particles suspended in waterglycerol- NaCl mixture. The particles with 20 μm diameter were selected to follow the flow of fluid. The flow at Re=155, 270 and 390 were investigated. The experimental result is compared with FLUENT simulated flow that account for viscous laminar flow model. The results suggest that laminar flow model was sufficient to predict flow velocity at the inlet but the velocity at stenosis throat at Re =390 was overestimated. Hence, a transition to turbulent regime might have been developed at throat region as the flow rate increases.
Abstract: The purpose of this study is two-fold. First, it attempts to explore potential opportunities for utilizing visual interactive simulations along with Business Intelligence (BI) as a decision support tool for strategic decision making. Second, it tries to figure out the essential top-level managerial requirements that would transform strategic decision simulation into an integral component of BI systems. The domain of particular interest was the application of visual interactive simulation capabilities in the field of supply chains. A qualitative exploratory method was applied, through the use of interviews with two leading companies. The collected data was then analysed to demonstrate the difference between the literature perspective and the practical managerial perspective on the issue. The results of the study suggest that although the use of simulation particularly in managing supply chains is very evident in literature, yet, in practice such utilization is still in its infancy, particularly regarding strategic decisions. Based on the insights a prototype of a simulation based BI-solution-extension was developed and evaluated.
Abstract: Traffic congestion has become a major problem in
many countries. One of the main causes of traffic congestion is due
to road merges. Vehicles tend to move slower when they reach the
merging point. In this paper, an enhanced algorithm for traffic
simulation based on the fluid-dynamic algorithm and kinematic wave
theory is proposed. The enhanced algorithm is used to study traffic
congestion at a road merge. This paper also describes the
development of a dynamic traffic simulation tool which is used as a
scenario planning and to forecast traffic congestion level in a certain
time based on defined parameter values. The tool incorporates the
enhanced algorithm as well as the two original algorithms. Output
from the three above mentioned algorithms are measured in terms of
traffic queue length, travel time and the total number of vehicles
passing through the merging point. This paper also suggests an
efficient way of reducing traffic congestion at a road merge by
analyzing the traffic queue length and travel time.
Abstract: This paper presents an adaptive technique for generation
of data required for construction of artificial neural network-based
performance model of nano-scale CMOS inverter circuit. The training
data are generated from the samples through SPICE simulation. The
proposed algorithm has been compared to standard progressive sampling
algorithms like arithmetic sampling and geometric sampling.
The advantages of the present approach over the others have been
demonstrated. The ANN predicted results have been compared with
actual SPICE results. A very good accuracy has been obtained.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..
Abstract: Many Wireless Sensor Network (WSN) applications necessitate secure multicast services for the purpose of broadcasting delay sensitive data like video files and live telecast at fixed time-slot. This work provides a novel method to deal with end-to-end delay and drop rate of packets. Opportunistic Routing chooses a link based on the maximum probability of packet delivery ratio. Null Key Generation helps in authenticating packets to the receiver. Markov Decision Process based Adaptive Scheduling algorithm determines the time slot for packet transmission. Both theoretical analysis and simulation results show that the proposed protocol ensures better performance in terms of packet delivery ratio, average end-to-end delay and normalized routing overhead.
Abstract: Virtual environment induces simulator sickness effect
for some users. The purpose of this research is to compare the
simulation sickness relative with parallax affect in one-screen and
three-screen HoloStageTM system, measured by Simulation Sickness
Questionnaire (SSQ). The results show the subjects tested in
three-screen has less sickness than one-screen and effect from the
Oculomotor (O) more than from the Disorientation (D) and more than
from the Nausea (N) or represented in O>D>N.
Abstract: This paper reports on a receding horizon filtering for
mobile robot systems with cross-correlated sensor noises and
uncertainties. Also, the effect of uncertain parameters in the state of
the tracking error model performance is considered. A distributed
fusion receding horizon filter is proposed. The distributed fusion
filtering algorithm represents the optimal linear combination of the
local filters under the minimum mean square error criterion. The
derivation of the error cross-covariances between the local receding
horizon filters is the key of this paper. Simulation results of the
tracking mobile robot-s motion demonstrate high accuracy and
computational efficiency of the distributed fusion receding horizon
filter.
Abstract: This paper presents a systematic approach for the
design of power system stabilizer using genetic algorithm and
investigates the robustness of the GA based PSS. The proposed
approach employs GA search for optimal setting of PSS parameters.
The performance of the proposed GPSS under small and large
disturbances, loading conditions and system parameters is tested.
The eigenvalue analysis and nonlinear simulation results show the
effectiveness of the GPSS to damp out the system oscillations. It is
found tat the dynamic performance with the GPSS shows improved
results, over conventionally tuned PSS over a wide range of
operating conditions.
Abstract: Adaptive control involves modifying the control law
used by the controller to cope with the fact that the parameters of the
system being controlled change drastically due to change in
environmental conditions or in system itself. This technique is based
on the fundamental characteristic of adaptation of living organism.
The adaptive control process is one that continuously and
automatically measures the dynamic behavior of plant, compares it
with the desired output and uses the difference to vary adjustable
system parameters or to generate an actuating signal in such a way so
that optimal performance can be maintained regardless of system
changes. This paper deals with application of model reference
adaptive control scheme in first order system. The rule which is used
for this application is MIT rule. This paper also shows the effect of
adaptation gain on the system performance. Simulation is done in
MATLAB and results are discussed in detail.
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: In this paper, estimation of the linear regression
model is made by ordinary least squares method and the
partially linear regression model is estimated by penalized
least squares method using smoothing spline. Then, it is
investigated that differences and similarity in the sum of
squares related for linear regression and partial linear
regression models (semi-parametric regression models). It is
denoted that the sum of squares in linear regression is reduced
to sum of squares in partial linear regression models.
Furthermore, we indicated that various sums of squares in the
linear regression are similar to different deviance statements in
partial linear regression. In addition to, coefficient of the
determination derived in linear regression model is easily
generalized to coefficient of the determination of the partial
linear regression model. For this aim, it is made two different
applications. A simulated and a real data set are considered to
prove the claim mentioned here. In this way, this study is
supported with a simulation and a real data example.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: To investigates the effect of fiberglass clamping
process improvement on drape simulation prediction. This has
great effect on the mould and the fiber during manufacturing
process. This also, improves the fiber strain, the quality of the
fiber orientation in the area of folding and wrinkles formation
during the press-forming process. Drape simulation software
tool was used to digitalize the process, noting the formation
problems on the contour sensitive part. This was compared
with the real life clamping processes using single and double
frame set-ups to observe the effects. Also, restrains are
introduced by using clips, and the G-clamps with predetermine
revolution to; restrain the fabric deformation during the
forming process.The incorporation of clamping and fabric
restrain deformation improved on the prediction of the
simulation tool. Therefore, for effective forming process,
incorporation of clamping process into the drape simulation
process will assist in the development of fiberglass application
in manufacturing process.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.