Abstract: Gas turbine air inlet cooling is a useful method for
increasing output for regions where significant power demand and
highest electricity prices occur during the warm months. Inlet air
cooling increases the power output by taking advantage of the gas
turbine-s feature of higher mass flow rate when the compressor inlet
temperature decreases. Different methods are available for reducing
gas turbine inlet temperature. There are two basic systems currently
available for inlet cooling. The first and most cost-effective system is
evaporative cooling. Evaporative coolers make use of the evaporation
of water to reduce the gas turbine-s inlet air temperature. The second
system employs various ways to chill the inlet air. In this method, the
cooling medium flows through a heat exchanger located in the inlet
duct to remove heat from the inlet air. However, the evaporative
cooling is limited by wet-bulb temperature while the chilling can cool
the inlet air to temperatures that are lower than the wet bulb
temperature. In the present work, a thermodynamic model of a gas
turbine is built to calculate heat rate, power output and thermal
efficiency at different inlet air temperature conditions. Computational
results are compared with ISO conditions herein called "base-case".
Therefore, the two cooling methods are implemented and solved for
different inlet conditions (inlet temperature and relative humidity).
Evaporative cooler and absorption chiller systems results show that
when the ambient temperature is extremely high with low relative
humidity (requiring a large temperature reduction) the chiller is the
more suitable cooling solution. The net increment in the power output
as a function of the temperature decrease for each cooling method is
also obtained.
Abstract: With data centers, end-users can realize the pervasiveness of services that will be one day the cornerstone of our lives. However, data centers are often classified as computing systems that consume the most amounts of power. To circumvent such a problem, we propose a self-adaptive weighted sum methodology that jointly optimizes the performance and power consumption of any given data center. Compared to traditional methodologies for multi-objective optimization problems, the proposed self-adaptive weighted sum technique does not rely on a systematical change of weights during the optimization procedure. The proposed technique is compared with the greedy and LR heuristics for large-scale problems, and the optimal solution for small-scale problems implemented in LINDO. the experimental results revealed that the proposed selfadaptive weighted sum technique outperforms both of the heuristics and projects a competitive performance compared to the optimal solution.
Abstract: A basic conceptual study of TCSC device on Simulink is a teaching aid and helps in understanding the rudiments of the topic. This paper thus stems out from basics of TCSC device and analyzes the impedance characteristics and associated single & multi resonance conditions. The Impedance characteristics curve is drawn for different values of inductance in MATLAB using M-files. The study is also helpful in estimating the appropriate inductance and capacitance values which have influence on multi resonance point in TCSC device. The capacitor voltage, line current, thyristor current and capacitor current waveforms are discussed briefly as simulation results. Simulink model of TCSC device is given and corresponding waveforms are analyzed. The subsidiary topics e.g. power oscillation damping, SSR mitigation and transient stability is also brought out.
Abstract: Using logarithmic mean Divisia decomposition technique, this paper analyzes the change in industrial energy intensity of Fujian Province in China, based on data sets of added value and energy consumption for 35 selected industrial sub-sectors from 1999 to 2009. The change in industrial energy intensity is decomposed into intensity effect and structure effect. Results show that the industrial energy intensity of Fujian Province has achieved a reduction of 51% over the past ten years. The structural change, a shift in the mix of industrial sub-sectors, made overwhelming contribution to the reduction. The impact of energy efficiency’s improvement was relatively small. However, the aggregate industrial energy intensity was very sensitive to both the changes in energy intensity and in production share of energy-intensive sub-sectors, such as production and supply of electric power, steam and hot water. Pathway to reduce industrial energy intensity for energy conservation in Fujian Province is proposed in the end.
Abstract: Power loss reduction is one of the main targets in power industry and so in this paper, the problem of finding the optimal configuration of a radial distribution system for loss reduction is considered. Optimal reconfiguration involves the selection of the best set of branches to be opened ,one each from each loop, for reducing resistive line losses , and reliving overloads on feeders by shifting the load to adjacent feeders. However ,since there are many candidate switching combinations in the system ,the feeder reconfiguration is a complicated problem. In this paper a new approach is proposed based on a simple optimum loss calculation by determining optimal trees of the given network. From graph theory a distribution network can be represented with a graph that consists a set of nodes and branches. In fact this problem can be viewed as a problem of determining an optimal tree of the graph which simultaneously ensure radial structure of each candidate topology .In this method the refined genetic algorithm is also set up and some improvements of algorithm are made on chromosome coding. In this paper an implementation of the algorithm presented by [7] is applied by modifying in load flow program and a comparison of this method with the proposed method is employed. In [7] an algorithm is proposed that the choice of the switches to be opened is based on simple heuristic rules. This algorithm reduce the number of load flow runs and also reduce the switching combinations to a fewer number and gives the optimum solution. To demonstrate the validity of these methods computer simulations with PSAT and MATLAB programs are carried out on 33-bus test system. The results show that the performance of the proposed method is better than [7] method and also other methods.
Abstract: Network reconfiguration in distribution system is realized by changing the status of sectionalizing switches to reduce the power loss in the system. This paper presents a new method which applies an artificial bee colony algorithm (ABC) for determining the sectionalizing switch to be operated in order to solve the distribution system loss minimization problem. The ABC algorithm is a new population based metaheuristic approach inspired by intelligent foraging behavior of honeybee swarm. The advantage of ABC algorithm is that it does not require external parameters such as cross over rate and mutation rate as in case of genetic algorithm and differential evolution and it is hard to determine these parameters in prior. The other advantage is that the global search ability in the algorithm is implemented by introducing neighborhood source production mechanism which is a similar to mutation process. To demonstrate the validity of the proposed algorithm, computer simulations are carried out on 14, 33, and 119-bus systems and compared with different approaches available in the literature. The proposed method has outperformed the other methods in terms of the quality of solution and computational efficiency.
Abstract: The use of power system stabilizers (PSSs) to damp
power system swing mode of oscillations is practical important. Our
purpose is to retune the power system stabilizer (PSS1A) parameters
in Unitrol D produced by ABB– was installed in 1995in Benghazi
North Power Plants (BNPPs) at General Electricity Company of
Libya (GECOL). The optimal values of the power system stabilizer
(PSS1A) parameters are determined off-line by a particle swarm
optimization technique (PSO). The objective is to damp the local and
inter-area modes of oscillations that occur following power system
disturbances. The retuned power system stabilizer (PSS1A) can cope
with large disturbance at different operating points and has enhanced
power system stability.
Abstract: Link reliability and transmitted power are two important design constraints in wireless network design. Error control coding (ECC) is a classic approach used to increase link reliability and to lower the required transmitted power. It provides coding gain, resulting in transmitter energy savings at the cost of added decoder power consumption. But the choice of ECC is very critical in the case of wireless sensor network (WSN). Since the WSNs are energy constraint in nature, both the BER and power consumption has to be taken into count. This paper develops a step by step approach in finding suitable error control codes for WSNs. Several simulations are taken considering different error control codes and the result shows that the RS(31,21) fits both in BER and power consumption criteria.
Abstract: In this paper, the effect of atmospheric turbulence on
bit error probability in free-space optical CDMA scheme with
Sequence Inverse Keyed (SIK) optical correlator receiver is analyzed.
Here Intensity Modulation scheme is considered for transmission.
The turbulence induced fading is described by the newly introduced
gamma-gamma pdf[1] as a tractable mathematical model for
atmospheric turbulence. Results are evaluated with Gold and Kasami
code & it is shown that Gold sequence can be used for more
efficient transmission than Kasami sequence in an atmospheric
turbulence channel.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: In recent years, scanning probe atomic force
microscopy SPM AFM has gained acceptance over a wide spectrum
of research and science applications. Most fields focuses on physical,
chemical, biological while less attention is devoted to manufacturing
and machining aspects. The purpose of the current study is to assess
the possible implementation of the SPM AFM features and its
NanoScope software in general machining applications with special
attention to the tribological aspects of cutting tool. The surface
morphology of coated and uncoated as-received carbide inserts is
examined, analyzed, and characterized through the determination of
the appropriate scanning setting, the suitable data type imaging
techniques and the most representative data analysis parameters
using the MultiMode SPM AFM in contact mode. The NanoScope
operating software is used to capture realtime three data types
images: “Height", “Deflection" and “Friction". Three scan sizes are
independently performed: 2, 6, and 12 μm with a 2.5 μm vertical
range (Z). Offline mode analysis includes the determination of three
functional topographical parameters: surface “Roughness", power
spectral density “PSD" and “Section". The 12 μm scan size in
association with “Height" imaging is found efficient to capture every
tiny features and tribological aspects of the examined surface. Also,
“Friction" analysis is found to produce a comprehensive explanation
about the lateral characteristics of the scanned surface. Configuration
of many surface defects and drawbacks has been precisely detected
and analyzed.
Abstract: In this paper, to resolve the problem of existing
schemes, an alternative fast handover Proxy Mobile IPv6 (PMIPv6)
scheme using the IEEE 802.21 Media Independent Handover (MIH)
function is proposed for heterogeneous wireless networks. The proposed
scheme comes to support fast handover for the mobile node
(MN) irrespective of the presence or absence of MIH functionality
as well as L3 mobility functionality, whereas the MN in existing
schemes has to implement MIH functionality. That is, the proposed
scheme does not require the MN to be involved in MIH related signaling
required for handover procedure. The base station (BS) with MIH
functionality performs handover on behalf of the MN. Therefore, the
proposed scheme can reduce burden and power consumption of MNs
with limited resource and battery power since MNs are not required
to be involved for the handover procedure. In addition, the proposed
scheme can reduce considerably traffic overhead over wireless links
between MN and BS since signaling messages are reduced.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: This study presents a new approach based on Tanaka's
fuzzy linear regression (FLP) algorithm to solve well-known power
system economic load dispatch problem (ELD). Tanaka's fuzzy linear
regression (FLP) formulation will be employed to compute the
optimal solution of optimization problem after linearization. The
unknowns are expressed as fuzzy numbers with a triangular
membership function that has middle and spread value reflected on
the unknowns. The proposed fuzzy model is formulated as a linear
optimization problem, where the objective is to minimize the sum of
the spread of the unknowns, subject to double inequality constraints.
Linear programming technique is employed to obtain the middle and
the symmetric spread for every unknown (power generation level).
Simulation results of the proposed approach will be compared with
those reported in literature.
Abstract: In this paper, the modified optimal sliding mode control with a proposed method to design a sliding surface is presented. Because of the inability of the previous approach of the sliding mode method to design a bounded and suitable input, the new variation is proposed in the sliding manifold to obviate problems in a structural system. Although the sliding mode control is a powerful method to reject disturbances and noises, the chattering problem is not good for actuators. To decrease the chattering phenomena, the optimal control is added to the sliding mode control. Not only the proposed method can decline the intense variations in the inputs of the system but also it can produce the efficient responses respect to the sliding mode control and optimal control that are shown by performing some numerical simulations.
Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: This research deals with techno economic analysis to select the most economic desalination method for Asalouyeh combined cycle power plant . Due to lack of fresh water, desalination of sea water is necessary to provide required DM water of Power Plant. The most common desalination methods are RO, MSF, MED, and MED–TVC. In this research, methods of RO, MED, and MED– TVC have been compared. Simulation results show that recovery of heat of exhaust gas of main stack is optimum case for providing DM water required for injected steam of MED desalination. This subject is very important because of improving thermal efficiency of power plant using extra heat recovery. Also, it has been shown that by adding 3 rows of finned tube to de-aerator evaporator, which is very simple and low cost, required steam for generating 5200 m3/day of desalinated water is obtainable.
Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: Transient simulation of power electronic circuits is of
considerable interest to the designer. The switching nature of the
devices used permits development of specialized algorithms which
allow a considerable reduction in simulation time compared to
general purpose simulation algorithms. This paper describes a
method used to simulate a power electronic circuits using the
SIMULINK toolbox within MATLAB software. Theoretical results
are presented provides the basis of transient analysis of a power
electronic circuits.
Abstract: In this paper, we proposed an efficient data
compression strategy exploiting the multi-resolution characteristic of
the wavelet transform. We have developed a sensor node called
“Smart Sensor Node; SSN". The main goals of the SSN design are
lightweight, minimal power consumption, modular design and robust
circuitry. The SSN is made up of four basic components which are a
sensing unit, a processing unit, a transceiver unit and a power unit.
FiOStd evaluation board is chosen as the main controller of the SSN
for its low costs and high performance. The software coding of the
implementation was done using Simulink model and MATLAB
programming language. The experimental results show that the
proposed data compression technique yields recover signal with good
quality. This technique can be applied to compress the collected data
to reduce the data communication as well as the energy consumption
of the sensor and so the lifetime of sensor node can be extended.