Abstract: Noise level has critical effects on the diagnostic
performance of signal-averaged electrocardiogram (SAECG), because
the true starting and end points of QRS complex would be masked by
the residual noise and sensitive to the noise level. Several studies and
commercial machines have used a fixed number of heart beats
(typically between 200 to 600 beats) or set a predefined noise level
(typically between 0.3 to 1.0 μV) in each X, Y and Z lead to perform
SAECG analysis. However different criteria or methods used to
perform SAECG would cause the discrepancies of the noise levels
among study subjects. According to the recommendations of 1991
ESC, AHA and ACC Task Force Consensus Document for the use of
SAECG, the determinations of onset and offset are related closely to
the mean and standard deviation of noise sample. Hence this study
would try to perform SAECG using consistent root-mean-square
(RMS) noise levels among study subjects and analyze the noise level
effects on SAECG. This study would also evaluate the differences
between normal subjects and chronic renal failure (CRF) patients in
the time-domain SAECG parameters.
The study subjects were composed of 50 normal Taiwanese and 20
CRF patients. During the signal-averaged processing, different RMS
noise levels were adjusted to evaluate their effects on three time
domain parameters (1) filtered total QRS duration (fQRSD), (2) RMS
voltage of the last QRS 40 ms (RMS40), and (3) duration of the low
amplitude signals below 40 μV (LAS40). The study results
demonstrated that the reduction of RMS noise level can increase
fQRSD and LAS40 and decrease the RMS40, and can further increase
the differences of fQRSD and RMS40 between normal subjects and
CRF patients. The SAECG may also become abnormal due to the
reduction of RMS noise level. In conclusion, it is essential to establish
diagnostic criteria of SAECG using consistent RMS noise levels for
the reduction of the noise level effects.
Abstract: In this work we study analytically and numerically the
performance of the mean heave motion of an OWC coupled with the
governing equation of the spreading ocean waves due to the wide
variation in an open parabolic channel with constant depth. This
paper considers that the ocean wave propagation is under the
assumption of a shallow flow condition. In order to verify the effect
of the waves in the OWC firstly we establish the analytical model in
a non-dimensional form based on the energy equation. The proposed
wave-power system has to aims: one is to perturb the ocean waves as
a consequence of the channel shape in order to concentrate the
maximum ocean wave amplitude in the neighborhood of the OWC
and the second is to determine the pressure and volume oscillation of
air inside the compression chamber.
Abstract: In this paper an approaches for increasing the
effectiveness of error detection in computer network channels with
Pulse-Amplitude Modulation (PAM) has been proposed. Proposed
approaches are based on consideration of special feature of errors,
which are appearances in line with PAM. The first approach consists
of CRC modification specifically for line with PAM. The second
approach is base of weighted checksums using. The way for
checksum components coding has been developed. It has been shown
that proposed checksum modification ensure superior digital data
control transformation reliability for channels with PAM in compare
to CRC.
Abstract: In this paper a bank of velocity filters is devised to be
used for isolating a moving object with specific velocity in a sequence of frames. The approach used is a 3-D FFT based experimental procedure without applying any theoretical concept
from velocity filters. Accordingly, velocity filters are built using the
spectral signature of each separate moving object. Experimentation
reveals the capabilities of the constructed filter bank to separate moving objects as far as the amplitude as well as the direction of the
velocity are concerned.
Abstract: The normalized difference vegetation index (NDVI)
and normalized difference moisture index (NDMI) derived from the
moderate resolution imaging spectroradiometer (MODIS) have been
widely used to identify spatial information of drought condition. The
relationship between NDVI and NDMI has been analyzed using
Pearson correlation analysis and showed strong positive relationship.
The drought indices have detected drought conditions and identified
spatial extents of drought. A comparison between normal year and
drought year demonstrates that the amplitude analysis considered both
vegetation and moisture condition is an effective method to identify
drought condition. We proposed the amplitude analysis is useful for
quick spatial assessment of drought information at a regional scale.
Abstract: Multi-user interference (MUI) is the main reason of system deterioration in the Spectral Amplitude Coding Optical Code Division Multiple Access (SAC-OCDMA) system. MUI increases with the number of simultaneous users, resulting into higher probability bit rate and limits the maximum number of simultaneous users. On the other hand, Phase induced intensity noise (PIIN) problem which is originated from spontaneous emission of broad band source from MUI severely limits the system performance should be addressed as well. Since the MUI is caused by the interference of simultaneous users, reducing the MUI value as small as possible is desirable. In this paper, an extensive study for the system performance specified by MUI and PIIN reducing is examined. Vectors Combinatorial (VC) codes families are adopted as a signature sequence for the performance analysis and a comparison with reported codes is performed. The results show that, when the received power increases, the PIIN noise for all the codes increases linearly. The results also show that the effect of PIIN can be minimized by increasing the code weight leads to preserve adequate signal to noise ratio over bit error probability. A comparison study between the proposed code and the existing codes such as Modified frequency hopping (MFH), Modified Quadratic- Congruence (MQC) has been carried out.
Abstract: A new code for spectral-amplitude coding optical
code-division multiple-access system is proposed called Random
diagonal (RD) code. This code is constructed using code segment and
data segment. One of the important properties of this code is that the
cross correlation at data segment is always zero, which means that
Phase Intensity Induced Noise (PIIN) is reduced. For the performance
analysis, the effects of phase-induced intensity noise, shot noise, and
thermal noise are considered simultaneously. Bit-error rate (BER)
performance is compared with Hadamard and Modified Frequency
Hopping (MFH) codes. It is shown that the system using this new
code matrices not only suppress PIIN, but also allows larger number
of active users compare with other codes. Simulation results shown
that using point to point transmission with three encoded channels,
RD code has better BER performance than other codes, also its found
that at 0 dbm PIIN noise are 10-10 and 10-11 for RD and MFH
respectively.
Abstract: An envelope echo signal measurement is proposed in
this paper using echo signal observation from the 200 kHz echo
sounder receiver. The envelope signal without any object is compared
with the envelope signal of the sphere. Two diameter size steel ball
(3.1 cm & 2.2 cm) and two diameter size air filled stainless steel ball
(4.8 cm & 7.4 cm) used in this experiment. The target was positioned
about 0.5 m and 1.0 meter from the transducer face using nylon rope.
From the echo observation in time domain, it is obviously shown that
echo signal structure is different between the size, distance and type
of metal sphere. The amplitude envelope voltage for the bigger
sphere is higher compare to the small sphere and it confirm that the
bigger sphere have higher target strength compare to the small
sphere. Although the structure signal without any object are different
compare to the signal from the sphere, the reflected signal from the
tank floor increase linearly with the sphere size. We considered this
event happened because of the object position approximately to the
tank floor.
Abstract: A spectrophotometric method was developed for simultaneous quantification of pseudoephedrine hydrochloride (PSE) triprolidine hydrochloride (TRI) using second derivative method (zero-crossing technique). The second derivative amplitudes of PSE and TRI were measured at 271 and 321 nm, respectively. The calibration curves were linear in the range of 200 to 1,000 g/ml for PSE and 10 to 50 g/ml for TRI. The method was validated for specificity, accuracy, precision, limit of detection and limit of quantitation. The proposed method was applied to the assaying and dissolution of PSE and TRI in commercial tablets without any chemical separation. The results were compared with those obtained by the official USP31 method and statistical tests showed that there is no significant between the methods at 95% confidence level. The proposed method is simple, rapid and suitable for the routine quality control application. KeywordsTriprolidine, Pseudoephedrine, Derivative spectrophotometry, Dissolution testing.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: Fractional delay FIR filters design method based on
the differential evolution algorithm is presented. Differential evolution
is an evolutionary algorithm for solving a global optimization problems in the continuous search space. In the proposed approach,
an evolutionary algorithm is used to determine the coefficients of
a fractional delay FIR filter based on the Farrow structure. Basic
differential evolution is enhanced with a restricted mating technique,
which improves the algorithm performance in terms of convergence
speed and obtained solution. Evolutionary optimization is carried out by minimizing an objective function which is based on the amplitude
response and phase delay errors. Experimental results show that the proposed algorithm leads to a reduction in the amplitude response and phase delay errors relative to those achieved with the Least-Squares
method.
Abstract: Indoor air distribution has great impact on people-s thermal sensation. Therefore, how to remove the indoor excess heat becomes an important issue to create a thermally comfortable indoor environment. To expel the extra indoor heat effectively, this paper used a dynamic CFD approach to study the effect of an air-supply guide vane swinging periodically on the indoor air distribution within a model room. The numerical results revealed that the indoor heat transfer performance caused by the swing guide vane had close relation with the number of vortices developing under the inlet cold jet. At larger swing amplitude, two smaller vortices continued to shed outward under the cold jet and remove the indoor heat load more effectively. As a result, it can be found that the average Nusselt number on the floor increased with the increase of the swing amplitude of the guide vane.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.
Abstract: In this paper we propose a family of algorithms based
on 3rd and 4th order cumulants for blind single-input single-output
(SISO) Non-Minimum Phase (NMP) Finite Impulse Response (FIR)
channel estimation driven by non-Gaussian signal. The input signal
represents the signal used in 10GBASE-T (or IEEE 802.3an-2006)
as a Tomlinson-Harashima Precoded (THP) version of random
Pulse-Amplitude Modulation with 16 discrete levels (PAM-16). The
proposed algorithms are tested using three non-minimum phase
channel for different Signal-to-Noise Ratios (SNR) and for different
data input length. Numerical simulation results are presented to
illustrate the performance of the proposed algorithms.
Abstract: Flows over a harmonically oscillating NACA 0012
airfoil are simulated here using a two-dimensional, unsteady,
incompressibleNavier-Stokes solver.Both pure-plunging and
pitching-plunging combined oscillations are considered at a Reynolds
number of 5000. Special attention is paid to the vortex shedding and
interaction mechanism of the motions. For all the simulations
presented here, the reduced frequency (k) is fixed at a value of 2.5
and plunging amplitude (h) is selected to be in the range of 0.2-0.5.
The simulation results show that the interaction mechanism between
the leading and trailing edge vortices has a decisive effect on the
values of the resulting thrust and propulsive efficiency.
Abstract: We propose the use of magneto-optic Kerr effect (MOKE) to realize single-qubit quantum gates. We consider longitudinal and polar MOKE in reflection geometry in which the magnetic field is parallel to both the plane of incidence and surface of the film. MOKE couples incident TE and TM polarized photons and the Hamiltonian that represents this interaction is isomorphic to that of a canonical two-level quantum system. By varying the phase and amplitude of the magnetic field, we can realize Hadamard, NOT, and arbitrary phase-shift single-qubit quantum gates. The principal advantage is operation with magnetically non-transparent materials.
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: In the power quality analysis non-stationary nature
of voltage distortions require some precise and powerful analytical
techniques. The time-frequency representation (TFR) provides a
powerful method for identification of the non-stationary of the
signals. This paper investigates a comparative study on two
techniques for analysis and visualization of voltage distortions with
time-varying amplitudes. The techniques include the Discrete
Wavelet Transform (DWT), and the S-Transform. Several power
quality problems are analyzed using both the discrete wavelet
transform and S–transform, showing clearly the advantage of the S–
transform in detecting, localizing, and classifying the power quality
problems.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: In this paper fatigue crack growth behavior of
aeronautical aluminum alloy 2024 T351 was studied. Effects of
various loading and geometrical parameters are studied such as stress
ratio, amplitude loading, etc. The fatigue crack growth with constant
amplitude is studied using the AFGROW code when NASGRO
model is used. The effect of the stress ratio is highlighted, where one
notices a shift of the curves of crack growth. The comparative study
between two orientations L-T and T-L on fatigue behavior are
presented and shows the variation on the fatigue life. L-T orientation
presents a good fatigue crack growth resistance. Effects of crack
closure are shown in Paris domain and that no crack closure
phenomenons are present at high stress intensity factor.