Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: This paper aimed to introduce the solution of concrete
slump recovery using chemical admixture type-F (superplasticizer,
naphthalene base) to the practice in order to solve unusable concrete
problem due to concrete loss its slump, especially for those tropical
countries that have faster slump loss rate. In the other hand, randomly
adding superplasticizer into concrete can cause concrete to segregate.
Therefore, this paper also develops the estimation model used to
calculate amount of second dose of superplasticizer need for concrete
slump recovery. Fresh properties of ordinary Portland cement
concrete with volumetric ratio of paste to void between aggregate
(paste content) of 1.1-1.3 with water-cement ratio zone of 0.30 to
0.67 and initial superplasticizer (naphthalene base) of 0.25%-1.6%
were tested for initial slump and slump loss for every 30 minutes for
one and half hour by slump cone test. Those concretes with slump
loss range from 10% to 90% were re-dosed and successfully
recovered back to its initial slump. Slump after re-dosed was tested
by slump cone test. From the result, it has been concluded that, slump
loss was slower for those mix with high initial dose of
superplasticizer due to addition of superplasticizer will disturb
cement hydration. The required second dose of superplasticizer was
affected by two major parameters, which were water-cement ratio
and paste content, where lower water-cement ratio and paste content
cause an increase in require second dose of superplasticizer. The
amount of second dose of superplasticizer is higher as the solid
content within the system is increase, solid can be either from cement
particles or aggregate. The data was analyzed to form an equation use
to estimate the amount of second dosage requirement of
superplasticizer to recovery slump to its original.
Abstract: Geopolymer composites reinforced with flax fabrics
and nanoclay are fabricated and studied for physical and mechanical
properties using X-Ray Diffraction (XRD), Fourier Transform
Infrared Spectroscopy (FTIR), and Scanning Electron Microscope
(SEM). Nanoclay platelets at a weight of 1.0%, 2.0%, and 3.0% were
added to geopolymer pastes. Nanoclay at 2.0 wt.% was found to
improve density and decrease porosity while improving flexural
strength and post-peak toughness. A microstructural analysis
indicated that nanoclay behaves as filler and as an activator
supporting geopolymeric reaction while producing a higher content
geopolymer gel improving the microstructure of binders. The process
enhances adhesion between the geopolymer matrix and flax fibres.
Abstract: In the past years electric mobility became part of a
public discussion. The trend to fully electrified vehicles instead of
vehicles fueled with fossil energy has notably gained momentum.
Today nearly every big car manufacturer produces and sells fully
electrified vehicles, but electrified vehicles are still not as competitive
as conventional powered vehicles. As the traction battery states the
largest cost driver, lowering its price is a crucial objective. In
addition to improvements in product and production processes a nonnegligible,
but widely underestimated cost driver of production can
be found in logistics, since the production technology is not
continuous yet and neither are the logistics systems. This paper presents an approach to evaluate cost factors on
different designs of load carrier systems. Due to numerous
interdependencies, the combination of costs factors for a particular
scenario is not transparent. This is effecting actions for cost reduction
negatively, but still cost reduction is one of the major goals for
simultaneous engineering processes. Therefore a concurrent and
phase appropriate cost valuation method is necessary to serve cost
transparency. In this paper the four phases of this cost valuation
method are defined and explained, which based upon a new approach
integrating the logistics development process in to the integrated
product and process development.
Abstract: Over the past few decades, manufacturing has evolved
from a more labor-intensive set of mechanical processes to a
sophisticated set of information based technology processes. With the
existence of various advanced manufacturing technologies (AMTs),
more and more functions or jobs are performed by these machines
instead of human labour. This study was undertaken in order to
research the extent of AMTs adoption in manufacturing companies in
Kenya. In order to investigate a survey was conducted via
questionnaires that were sent to 183 selected AMT manufacturing
companies in Kenya. 92 companies responded positively. All the
surveyed companies were found to have a measure of investment in
at least two of the 14 types of AMTs investigated. In general the
company surveyed showed that the level of AMT adoption in Kenya
is very low with investments levels at a mean of 2.057 and
integration levels at a mean of 1.639 in a scale of 1-5.
Abstract: In the recent past, discussing about sex among
children and youths was frowned at by traditional norms and as such
sexual discussions and behavior were approached with great respect.
Things are actually falling apart with the increasing number of young
people that engage in premarital sex. Due to lack of experience and
sex education, many young people are becoming increasingly
exposed to the risk of HIV infection. In the light of the above, this
study discussed premarital sex, HIV, and use of condom among
youths in Nigeria. Data for this study came from 2013 Nigeria
Demographic and Health Survey and other secondary data. The
survey revealed that only 18.5 percent of young women that had sex
in the 12 months preceding the survey used condom. Out of 3306
never-married sexually active men and women, 1728 representing 52
percent live in urban areas and 43 percent of them did not use
condom during sexual intercourse in the 12 months preceding the
survey. This study concludes that for there to be reduction in
prevalence of HIV/AIDS among Nigerian youths, there is need for
concerted effort to be made towards educating youths on the
expedient of the use of condom during sexual intercourse.
Abstract: Countryside has been generally recognized and
regarded as a characteristic symbol which presents in human memory
for a long time. As a result of the change of times, because of it is
failure to meet the growing needs of the growing life and mental
decline, the vast rural area began to decline. But their history feature
image which accumulated by the ancient tradition provides people
with the origins of existence on the spiritual level, such as "identity"
and "belonging", makes people closer to the others in the spiritual and
psychological aspects of a common experience about the past, thus the
sense of a lack of culture caused by the losing of memory symbols is
weakened. So, in the modernization process, how to repair its vitality
and transform and planning it in a sustainable way has become a hot
topics in architectural and urban planning. This paper aims to break
the constraints of disciplines, from the perspective of interdiscipline,
using the research methods of systems science to analyze and discuss
the theories and methods of rural form factors, which based on the
viewpoint of memory in psychology. So we can find a right way to
transform the Rural to give full play to the role of the countryside in
the actual use and the shape of history spirits.
Abstract: Prediction of maximum local scour is necessary for
the safety and economical design of the bridges. A number of
equations have been developed over the years to predict local scour
depth using laboratory data and a few pier equations have also been
proposed using field data. Most of these equations are empirical in
nature as indicated by the past publications. In this paper attempts
have been made to compute local depth of scour around bridge pier in
dimensional and non-dimensional form by using linear regression,
simple regression and SVM (Poly & Rbf) techniques along with few
conventional empirical equations. The outcome of this study suggests
that the SVM (Poly & Rbf) based modeling can be employed as an
alternate to linear regression, simple regression and the conventional
empirical equations in predicting scour depth of bridge piers. The
results of present study on the basis of non-dimensional form of
bridge pier scour indicate the improvement in the performance of
SVM (Poly & Rbf) in comparison to dimensional form of scour.
Abstract: People, throughout the history, have made estimates
and inferences about the future by using their past experiences.
Developing information technologies and the improvements in the
database management systems make it possible to extract useful
information from knowledge in hand for the strategic decisions.
Therefore, different methods have been developed. Data mining by
association rules learning is one of such methods. Apriori algorithm,
one of the well-known association rules learning algorithms, is not
commonly used in spatio-temporal data sets. However, it is possible
to embed time and space features into the data sets and make Apriori
algorithm a suitable data mining technique for learning spatiotemporal
association rules. Lake Van, the largest lake of Turkey, is a
closed basin. This feature causes the volume of the lake to increase or
decrease as a result of change in water amount it holds. In this study,
evaporation, humidity, lake altitude, amount of rainfall and
temperature parameters recorded in Lake Van region throughout the
years are used by the Apriori algorithm and a spatio-temporal data
mining application is developed to identify overflows and newlyformed
soil regions (underflows) occurring in the coastal parts of
Lake Van. Identifying possible reasons of overflows and underflows
may be used to alert the experts to take precautions and make the
necessary investments.
Abstract: Red pepper (Capsicum annum L.) has long been
recognized as a good source of antioxidants, being rich in ascorbic
acid and other phytochemicals. In Turkish cuisine red pepper is
sometimes consumed raw in salads and baked as a garnish, but its
most wide consumption type is red pepper paste. The processing of
red pepper into pepper paste includes various thermal treatment steps
such as heating and pasteurizing. There are reports demonstrating an
enhancement or reduction in antioxidant activity of vegetables after
thermal treatment. So this study was conducted to investigate the
total phenolic, ascorbic acid and total carotenoids as well as free
radical scavenging activity of raw red pepper and various red pepper
pastes obtainable on the market. The samples were analyzed for
radical-scavenging activity (RSA) and total polyphenol (TP) content
using 1,1-diphenyl-2-picrylhydrazyl (DPPH) and Folin-Ciocalteu
methods, respectively. Total carotenoids and ascorbic acid contents
were determined spectrophotometrically. Results suggest that hot
pepper paste contained significantly (P0.05) difference in RSA, ascorbic acid and total carotenoids
content between sweet and hot red pepper paste products. It is
concluded that the red pepper paste, that has a wide range of
consumption in Turkish cuisine, presents a good dose of phenolic
compounds and antioxidant capacity and it should be regarded as a
functional food.
Abstract: Natural admixtures provide concrete with enhanced
properties but their processing end up making them very expensive
resulting in increase to cost of concrete. In this study the effect
of Gum from Acacia Karroo (GAK) as set-retarding admixture
in cement pastes was studied. The possibility of using GAK as
water reducing admixture both in cement mortar concrete was
also investigated. Cement pastes with different dosages of GAK
were prepared to measure the setting time using different dosages.
Compressive strength of cement mortars with 0.7, 0.8 and 0.9%
weight of cement and w/c ratio of 0.5 were compared to those with
water cement (w/c) ratio of 0.44 but same dosage of GAK. Concrete
samples were prepared using higher dosages of GAK (1, 2 and 3%
wt of cement) and a water bidder (w/b) of 0.61 were compared to
those with the same GAK dosage but with reduced w/b ratio. There
was increase in compressive strength of 9.3% at 28 days for cement
mortar samples with 0.9% dosage of GAK and reduced w/c ratio.
Abstract: Financial inclusion has become a crucially important
factor in debates on economic inequality posing challenges to the
financial systems of countries around the world. Nowadays
governments and banks are concerned about creating products that
allow access to wide sectors of the population. The creation of
banking products by the financial sector for people with low incomes
tends to lead to improvements in the quality of life of vulnerable parts
of the population. In countries with notable social and economic
inequalities, financial inclusion is a key aspect for equitable
economic growth. This study is based on the case of Colombia, which is a country
with a strong record of economic growth over the past decade.
Nevertheless, corruption, unemployment, and poverty contribute to
uncertainty regarding the country’s future growth prospects. This study wants to explain the situation of financial exclusion and
financial inclusion with respect to the Colombian case. Financial
inclusion is going to be studied from the perspective of social
innovation.
Abstract: Structural failure is caused mainly by damage that
often occurs on structures. Many researchers focus on to obtain very
efficient tools to detect the damage in structures in the early state. In
the past decades, a subject that has received considerable attention in
literature is the damage detection as determined by variations in the
dynamic characteristics or response of structures. The study presents
a new damage identification technique. The technique detects the
damage location for the incomplete structure system using output
data only. The method indicates the damage based on the free
vibration test data by using ‘Two Points Condensation (TPC)
technique’. This method creates a set of matrices by reducing the
structural system to two degrees of freedom systems. The current
stiffness matrices obtain from optimization the equation of motion
using the measured test data. The current stiffness matrices compare
with original (undamaged) stiffness matrices. The large percentage
changes in matrices’ coefficients lead to the location of the damage. TPC technique is applied to the experimental data of a simply
supported steel beam model structure after inducing thickness change
in one element, where two cases consider. The method detects the
damage and determines its location accurately in both cases. In
addition, the results illustrate these changes in stiffness matrix can be
a useful tool for continuous monitoring of structural safety using
ambient vibration data. Furthermore, its efficiency proves that this
technique can be used also for big structures.
Abstract: Social Avoidance is one of the most important
problems that face a good number of disabled students. It results from
the negative attitudes of non-disabled students, teachers and others.
Some of the past research has shown that non-disabled individuals
hold negative attitudes toward persons with disabilities. The present
study aims to alleviate Social Avoidance by applying the Cognitive
Behavioral Intervention. 24 Blind students aged 19–24 (university students) were randomly
chosen we compared an experimental group (consisted of 12
students) who went through the intervention program, with a control
group (12 students also) who did not go through such intervention.
We used the Social Avoidance and Distress Scale (SADS) to assess
social anxiety and distress behavior. The author used many
techniques of cognitive behavioral intervention such as modeling,
cognitive restructuring, extension, contingency contracts, selfmonitoring,
assertiveness training, role play, encouragement and
others. Statistically, T-test was employed to test the research
hypothesis. Result showed that there is a significance difference between the
experimental group and the control group after the intervention and
also at the follow up stages of the Social Avoidance and Distress
Scale. Also for the experimental group, there is a significance
difference before the intervention and the follow up stages for the
scale. Results showed that, there is a decrease in social avoidance.
Accordingly, cognitive behavioral intervention program was
successful in decreasing social avoidance for blind students.
Abstract: In the past few years, high consumption of soft drinks
has attracted negative attention world-wide due to its possible
adverse effects, leading the health conscious people to find
alternative nutraceutical or herbal health drinks. In the present study,
a nutraceutical soft drink was developed utilizing some easily
available and well known traditional herbs having nutritional
potential. The key ingredients were selected as bael, amla, lemon
juice, ashwagandha and poppy seeds based on their household routine
use in the summer with proven refreshing, cooling and energetic
feeling since ages. After several trials made, the final composition of
nutraceutical summer soft drink was selected as most suitable
combination based on the taste, physicochemical, microbial and
organoleptic point of view. The physicochemical analysis of the
prepared drink found to contain optimum level of titratable acidity,
total soluble solids and pH which were in accordance of the
commercial recommendations. There were no bacterial colonies
found in the product therefore found within limits. During the nine
point’s hedonic scale sensory evaluation, the drink was strongly liked
for colour, taste, flavour and texture. The formulation was found to
contain flavonoids (80mg/100ml), phenolics (103mg/100ml), vitamin
C (250mg/100ml) and has antioxidant potential (75.52%) apart from
providing several other essential vitamins, minerals and healthy
components. The developed nutraceutical drink provides an
economical and feasible option for the consumers with very good
taste combined with potential health benefits. The present drink is
potentially capable to replace the synthetic soft drinks available in the
market.
Abstract: This study aims to increase understanding of the
transition of business models in servitization. The significance of
service in all business has increased dramatically during the past
decades. Service-dominant logic (SDL) describes this change in the
economy and questions the goods-dominant logic on which business
has primarily been based in the past. A business model canvas is one
of the most cited and used tools in defining end developing business
models. The starting point of this paper lies in the notion that the
traditional business model canvas is inherently goods-oriented and
best suits for product-based business. However, the basic differences
between goods and services necessitate changes in business model
representations when proceeding in servitization. Therefore, new
knowledge is needed on how the conception of business model and
the business model canvas as its representation should be altered in
servitized firms in order to better serve business developers and interfirm
co-creation. That is to say, compared to products, services are
intangible and they are co-produced between the supplier and the
customer. Value is always co-created in interaction between a
supplier and a customer, and customer experience primarily depends
on how well the interaction succeeds between the actors. The role of
service experience is even stronger in service business compared to
product business, as services are co-produced with the customer. This paper provides business model developers with a service
business model canvas, which takes into account the intangible,
interactive, and relational nature of service. The study employs a
design science approach that contributes to theory development via
design artifacts. This study utilizes qualitative data gathered in
workshops with ten companies from various industries. In particular,
key differences between Goods-dominant logic (GDL) and SDLbased
business models are identified when an industrial firm
proceeds in servitization. As the result of the study, an updated version of the business
model canvas is provided based on service-dominant logic. The
service business model canvas ensures a stronger customer focus and
includes aspects salient for services, such as interaction between
companies, service co-production, and customer experience. It can be
used for the analysis and development of a current service business
model of a company or for designing a new business model. It
facilitates customer-focused new service design and service
development. It aids in the identification of development needs, and
facilitates the creation of a common view of the business model.
Therefore, the service business model canvas can be regarded as a
boundary object, which facilitates the creation of a common
understanding of the business model between several actors involved.
The study contributes to the business model and service business
development disciplines by providing a managerial tool for
practitioners in service development. It also provides research insight
into how servitization challenges companies’ business models.
Abstract: Water resource systems modeling has constantly been
a challenge through history for human beings. As the innovative
methodological development is evolving alongside computer sciences
on one hand, researches are likely to confront more complex and
larger water resources systems due to new challenges regarding
increased water demands, climate change and human interventions,
socio-economic concerns, and environment protection and
sustainability. In this research, an automatic calibration scheme has
been applied on the Gilan’s large-scale water resource model using
mathematical programming. The water resource model’s calibration
is developed in order to attune unknown water return flows from
demand sites in the complex Sefidroud irrigation network and other
related areas. The calibration procedure is validated by comparing
several gauged river outflows from the system in the past with model
results. The calibration results are pleasantly reasonable presenting a
rational insight of the system. Subsequently, the unknown optimized
parameters were used in a basin-scale linear optimization model with
the ability to evaluate the system’s performance against a reduced
inflow scenario in future. Results showed an acceptable match
between predicted and observed outflows from the system at selected
hydrometric stations. Moreover, an efficient operating policy was
determined for Sefidroud dam leading to a minimum water shortage
in the reduced inflow scenario.
Abstract: The current paper presents the results of a conducted
case study. During the past few years the number of children
diagnosed with Learning Difficulties has drastically augmented and
especially the cases of ADHD (Attention Deficit Hyperactivity
Disorder). One of the core characteristics of ADHD is a deficit in
working memory functions. The review of the literature indicates a
plethora of educational software that aim at training and enhancing
the working memory. Nevertheless, in the current paper, the
possibility of using for the same purpose free, online games will be
explored. Another issue of interest is the potential effect of the
working memory training to the core symptoms of ADHD. In order
to explore the abovementioned research questions, three digital tests
are employed, all of which are developed on the E-slate platform by
the author, in order to check the levels of ADHD’s symptoms and to
be used as diagnostic tools, both in the beginning and in the end of
the case study. The tools used during the main intervention of the
research are free online games for the training of working memory.
The research and the data analysis focus on the following axes: a) the
presence and the possible change in two of the core symptoms of
ADHD, attention and impulsivity and b) a possible change in the
general cognitive abilities of the individual. The case study was
conducted with the participation of a thirteen year-old, female
student, diagnosed with ADHD, during after-school hours. The
results of the study indicate positive changes both in the levels of
attention and impulsivity. Therefore, we conclude that the training of
working memory through the use of free, online games has a positive
impact on the characteristics of ADHD. Finally, concerning the
second research question, the change in general cognitive abilities, no
significant changes were noted.
Abstract: Laban Movement Analysis (LMA), developed in the
dance community over the past seventy years, is an effective method
for observing, describing, notating, and interpreting human
movement to enhance communication and expression in everyday
and professional life. Many applications that use motion capture data
might be significantly leveraged if the Laban qualities will be
recognized automatically. This paper presents an automated
recognition method of Laban qualities from motion capture skeletal
recordings and it is demonstrated on the output of Microsoft’s Kinect
V2 sensor.
Abstract: Over the past few years, a lot of research has been
conducted to bring Automatic Speech Recognition (ASR) into various
areas of Air Traffic Control (ATC), such as air traffic control
simulation and training, monitoring live operators for with the aim
of safety improvements, air traffic controller workload measurement
and conducting analysis on large quantities controller-pilot speech.
Due to the high accuracy requirements of the ATC context and its
unique challenges, automatic speech recognition has not been widely
adopted in this field. With the aim of providing a good starting
point for researchers who are interested bringing automatic speech
recognition into ATC, this paper gives an overview of possibilities
and challenges of applying automatic speech recognition in air traffic
control. To provide this overview, we present an updated literature
review of speech recognition technologies in general, as well as
specific approaches relevant to the ATC context. Based on this
literature review, criteria for selecting speech recognition approaches
for the ATC domain are presented, and remaining challenges and
possible solutions are discussed.