Abstract: This paper presents the doping profile measurement
and characterization technique for the pocket implanted nano scale
n-MOSFET. Scanning capacitance microscopy and atomic force
microscopy have been used to image the extent of lateral dopant
diffusion in MOS structures. The data are capacitance vs. voltage
measurements made on a nano scale device. The technique is nondestructive
when imaging uncleaved samples. Experimental data from
the published literature are presented here on actual, cleaved device
structures which clearly indicate the two-dimensional dopant profile
in terms of a spatially varying modulated capacitance signal. Firstorder
deconvolution indicates the technique has much promise for
the quantitative characterization of lateral dopant profiles. The pocket
profile is modeled assuming the linear pocket profiles at the source
and drain edges. From the model, the effective doping concentration
is found to use in modeling and simulation results of the various
parameters of the pocket implanted nano scale n-MOSFET. The
potential of the technique to characterize important device related
phenomena on a local scale is also discussed.
Abstract: The interaction of tunneling or mining with
groundwater has become a very relevant problem not only due to the
need to guarantee the safety of workers and to assure the efficiency of
the tunnel drainage systems, but also to safeguard water resources
from impoverishment and pollution risk. Therefore it is very
important to forecast the drainage processes (i.e., the evaluation of
drained discharge and drawdown caused by the excavation). The aim
of this study was to know better the system and to quantify the flow
drained from the Fontane mines, located in Val Germanasca (Turin,
Italy). This allowed to understand the hydrogeological local changes
in time. The work has therefore been structured as follows: the
reconstruction of the conceptual model with the geological,
hydrogeological and geological-structural study; the calculation of
the tunnel inflows (through the use of structural methods) and the
comparison with the measured flow rates; the water balance at the
basin scale. In this way it was possible to understand what are the
relationships between rainfall, groundwater level variations and the
effect of the presence of tunnels as a means of draining water.
Subsequently, it the effects produced by the excavation of the mining
tunnels was quantified, through numerical modeling. In particular,
the modeling made it possible to observe the drawdown variation as a
function of number, excavation depth and different mines linings.
Abstract: the data quality is a kind of complex and unstructured concept, which is concerned by information systems managers. The reason of this attention is the high amount of Expenses for maintenance and cleaning of the inefficient data. Such a data more than its expenses of lack of quality, cause wrong statistics, analysis and decisions in organizations. Therefor the managers intend to improve the quality of their information systems' data. One of the basic subjects of quality improvement is the evaluation of the amount of it. In this paper, we present a precautionary method, which with its application the data of information systems would have a better quality. Our method would cover different dimensions of data quality; therefor it has necessary integrity. The presented method has tested on three dimensions of accuracy, value-added and believability and the results confirm the improvement and integrity of this method.
Abstract: A different concept for designing and detailing of
reinforced concrete precast frame structures is analyzed in this paper.
The new detailing of the joints derives from the special hybrid
moment frame joints. The special reinforcements of this alternative
detailing, named modified special hybrid joint, are bondless with
respect to both column and beams. Full scale tests were performed on
a plan model, which represents a part of 5 story structure, cropped in
the middle of the beams and columns spans. Theoretical approach
was developed, based on testing results on twice repaired model,
subjected to lateral seismic type loading. Discussion regarding the
modified special hybrid joint behavior and further on widening
research needed concludes the presentation.
Abstract: The physical methods for RNA secondary structure prediction are time consuming and expensive, thus methods for computational prediction will be a proper alternative. Various algorithms have been used for RNA structure prediction including dynamic programming and metaheuristic algorithms. Musician's behaviorinspired harmony search is a recently developed metaheuristic algorithm which has been successful in a wide variety of complex optimization problems. This paper proposes a harmony search algorithm (HSRNAFold) to find RNA secondary structure with minimum free energy and similar to the native structure. HSRNAFold is compared with dynamic programming benchmark mfold and metaheuristic algorithms (RnaPredict, SetPSO and HelixPSO). The results showed that HSRNAFold is comparable to mfold and better than metaheuristics in finding the minimum free energies and the number of correct base pairs.
Abstract: Bioinformatics and Cheminformatics use computer as disciplines providing tools for acquisition, storage, processing, analysis, integrate data and for the development of potential applications of biological and chemical data. A chemical database is one of the databases that exclusively designed to store chemical information. NMRShiftDB is one of the main databases that used to represent the chemical structures in 2D or 3D structures. SMILES format is one of many ways to write a chemical structure in a linear format. In this study we extracted Antimicrobial Structures in SMILES format from NMRShiftDB and stored it in our Local Data Warehouse with its corresponding information. Additionally, we developed a searching tool that would response to user-s query using the JME Editor tool that allows user to draw or edit molecules and converts the drawn structure into SMILES format. We applied Quick Search algorithm to search for Antimicrobial Structures in our Local Data Ware House.
Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: The rotation of starting pitchers is a strategic issue
which has a significant impact on the performance of a professional
team. Choosing an optimal starting pitcher from among many
alternatives is a multi-criteria decision-making (MCDM) problem. In
this study, a model using the Analytic Hierarchy Process (AHP) and
Technique for Order Performance by Similarity to the Ideal Solution
(TOPSIS) is proposed with which to arrange the starting pitcher
rotation for teams of the Chinese Professional Baseball League. The
AHP is used to analyze the structure of the starting pitcher selection
problem and to determine the weights of the criteria, while the
TOPSIS method is used to make the final ranking. An empirical
analysis is conducted to illustrate the utilization of the model for the
starting pitcher rotation problem. The results demonstrate the
effectiveness and feasibility of the proposed model.
Abstract: The current trend of increasing quality and demands
of the final product is affected by time analysis of the entire
manufacturing process. The primary requirement of manufacturing is
to produce as many products as soon as possible, at the lowest
possible cost, but of course with the highest quality. Such
requirements may be satisfied only if all the elements entering and
affecting the production cycle are in a fully functional condition.
These elements consist of sensory equipment and intelligent control
elements that are essential for building intelligent manufacturing
systems. The intelligent manufacturing paradigm includes a new
approach to production system structure design. Intelligent behaviors
are based on the monitoring of important parameters of system and
its environment. The flexible reaction to changes. The realization and
utilization of this design paradigm as an "intelligent manufacturing
system" enables the flexible system reaction to production
requirement as soon as environmental changes too. Results of these
flexible reactions are a smaller layout space, be decreasing of
production and investment costs and be increasing of productivity.
Intelligent manufacturing system itself should be a system that can
flexibly respond to changes in entering and exiting the process in
interaction with the surroundings.
Abstract: This paper is focused on issues of process modeling
and two model based control strategies of a fed-batch sugar
crystallization process applying the concept of artificial neural
networks (ANNs). The control objective is to force the operation into
following optimal supersaturation trajectory. It is achieved by
manipulating the feed flow rate of sugar liquor/syrup, considered as
the control input. The control task is rather challenging due to the
strong nonlinearity of the process dynamics and variations in the
crystallization kinetics. Two control alternatives are considered –
model predictive control (MPC) and feedback linearizing control
(FLC). Adequate ANN process models are first built as part of the
controller structures. MPC algorithm outperforms the FLC approach
with respect to satisfactory reference tracking and smooth control
action. However, the MPC is computationally much more involved
since it requires an online numerical optimization, while for the FLC
an analytical control solution was determined.
Abstract: For Seismic design, it is important to estimate,
maximum lateral displacement (inelastic displacement) of the
structures due to sever earthquakes for several reasons. Seismic
design provisions estimate the maximum roof and storey drifts
occurring in major earthquakes by amplifying the drifts of the
structures obtained by elastic analysis subjected to seismic design
load, with a coefficient named “displacement amplification factor"
which is greater than one. Here, this coefficient depends on various
parameters, such as ductility and overstrength factors. The present
research aims to evaluate the value of the displacement amplification
factor in seismic design codes and then tries to propose a value to
estimate the maximum lateral structural displacement from sever
earthquakes, without using non-linear analysis. In seismic codes,
since the displacement amplification is related to “force reduction
factor" hence; this aspect has been accepted in the current study.
Meanwhile, two methodologies are applied to evaluate the value of
displacement amplification factor and its relation with the force
reduction factor. In the first methodology, which is applied for all
structures, the ratio of displacement amplification and force reduction
factors is determined directly. Whereas, in the second methodology
that is applicable just for R/C moment resisting frame, the ratio is
obtained by calculating both factors, separately. The acquired results
of these methodologies are alike and estimate the ratio of two factors
from 1 to 1.2. The results indicate that the ratio of the displacement
amplification factor and the force reduction factor differs to those
proposed by seismic provisions such as NEHRP, IBC and Iranian
seismic code (standard no. 2800).
Abstract: Nowadays, a passenger car suspension must has high
performance criteria with light weight, low cost, and low energy
consumption. Pilot controlled proportional valve is designed and
analyzed to get small pressure change rate after blow-off, and to get a
fast response of the damper, a reverse damping mechanism is adapted.
The reverse continuous variable damper is designed as a HS-SH
damper which offers good body control with reduced transferred input
force from the tire, compared with any other type of suspension
system. The damper structure is designed, so that rebound and
compression damping forces can be tuned independently, of which the
variable valve is placed externally. The rate of pressure change with
respect to the flow rate after blow-off becomes smooth when the fixed
orifice size increases, which means that the blow-off slope is
controllable using the fixed orifice size. Damping forces are measured
with the change of the solenoid current at the different piston
velocities to confirm the maximum hysteresis of 20 N, linearity, and
variance of damping force. The damping force variance is wide and
continuous, and is controlled by the spool opening, of which scheme is
usually adapted in proportional valves. The reverse continuous
variable damper developed in this study is expected to be utilized in
the semi-active suspension systems in passenger cars after its
performance and simplicity of the design is confirmed through a real
car test.
Abstract: It is the living conditions in the cities that determine the future of our livelihood. “To change life, we must first change space"- Henri Lefebvre. Sustainable development is a utopian aspiration for South African cities (especially the case study of the Gauteng City Region), which are currently characterized by unplanned growth and increasing urban sprawl. While the reasons for poor environmental quality and living conditions are undoubtedly diverse and complex, having political, economical and social dimensions, it is argued that the prevailing approach to layout planning in South Africa is part of the problem. This article seeks a solution to the problem of sustainability, from a spatial planning perspective. The spatial planning tool, the urban development boundary, is introduced as the concept that will ensure empty talk being translated into a sustainable vision. The urban development boundary is a spatial planning tool that can be used and implemented to direct urban growth towards a more sustainable form. The urban development boundary aims to ensure planned urban areas, in contrast to the current unplanned areas characterized by urban sprawl and insufficient infrastructure. However, the success of the urban development boundary concept is subject to effective implementation measures, as well as adequate and efficient management. The concept of sustainable development can function as a driving force underlying societal change and transformation, but the interface between spatial planning and environmental management needs to be established (as this is the core aspects underlying sustainable development), and authorities needs to understand and implement this interface consecutively. This interface can, however, realize in terms of the objectives of the planning tool – the urban development boundary. The case study, the Gauteng City Region, is depicted as a site of economic growth and innovation, but there is a lack of good urban and regional governance, impacting on the design (layout) and function of urban areas and land use, as current authorities make uninformed decisions in terms of development applications, leading to unsustainable urban forms and unsustainable nodes. Place and space concepts are thus critical matters applicable to planning of the Gauteng City Region. The urban development boundary are thus explored as a planning tool to guide decision-making, and create a sustainable urban form, leading to better environmental and living conditions, and continuous sustainability.
Abstract: In this paper optimal capacitor placement problem has
been formulated in a restructured distribution network. In this
scenario the distribution network operator can consider reactive
energy also as a service that can be sold to transmission system. Thus
search for optimal location, size and number of capacitor banks with
the objective of loss reduction, maximum income from selling
reactive energy to transmission system and return on investment for
capacitors, has been performed. Results is influenced with economic
value of reactive energy, therefore problem has been solved for
various amounts of it. The implemented optimization technique is
genetic algorithm. For any value of reactive power economic value,
when reverse of investment index increase and change from zero or
negative values to positive values, the threshold value of selling
reactive power has been obtained. This increasing price of economic
parameter is reasonable until the network losses is less than loss
before compensation.
Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.
Abstract: This paper deals with the status of solid waste pollution in touristic spots of North coastal Andhra Pradesh. Case studies of Eco tourism, cultural tourism and pilgrim tourism are elaborately discussed and the study is based on both primary and secondary data. Data collection includes field collection of solid waste, semi structured interviews and observation of tourists. Results indicate generation of 72% Non biodegradable material in Eco touristic places like RK beach Visakhapatnam, Araku Valley. Pydithalli Jathra is a famous cultural touristic attraction and more than one lakh people converge here. The solid waste at this spot includes 20% coconut shells, 50% plastic bottles and covers, 20% Banana peelings and remaining are food materials. Radhasapthami is the most important festival celebrated at famous sun temple Arasavalli of Srikakulam. Here solid waste includes 50% water bottles, plastic covers, 10% papers, 10% hair, 30% left out food material and Banana peelings.
Abstract: In the traditional buckling analysis of rectangular
plates the classical thin plate theory is generally applied, so
neglecting the plating shear deformation. It seems quite clear that this
method is not totally appropriate for the analysis of thick plates, so
that in the following the two variable refined plate theory proposed
by Shimpi (2006), that permits to take into account the transverse
shear effects, is applied for the buckling analysis of simply supported
isotropic rectangular plates, compressed in one and two orthogonal
directions.
The relevant results are compared with the classical ones and, for
rectangular plates under uniaxial compression, a new direct
expression, similar to the classical Bryan-s formula, is proposed for
the Euler buckling stress.
As the buckling analysis is a widely diffused topic for a variety of
structures, such as ship ones, some applications for plates uniformly
compressed in one and two orthogonal directions are presented and
the relevant theoretical results are compared with those ones obtained
by a FEM analysis, carried out by ANSYS, to show the feasibility of
the presented method.
Abstract: Supplier appraisal fosters energy in Supply Chain
Management and helps in best optimization of viable business
partners for a company. Many Decision Making techniques have
already been proposed by researchers for supplier-s appraisal.
However, Analytic Hierarchy Process (AHP) is assumed to be the
most structured technique to attain near-best solution of the problem.
This paper focuses at implementation of AHP in the procurement
processes. It also suggests that on what factors a Public Sector
Enterprises must focus while dealing with their suppliers and what
should the suppliers do to synchronize their activities with the
strategic objectives of Organization. It also highlights the weak areas
in supplier appraisal process with a view to suggest viable
recommendations.
Abstract: A study of the H-beam's nanosize structure phase
states after thermomechanical strengthening was carried out by TEM.
The following processes were analyzed. 1. The dispersing of the
cementite plates by cutting them by moving dislocations. 2. The
dissolution of cementite plates and repeated precipitation of the
cementite particles on the dislocations, the boundaries, subgrains and
grains. 3. The decay of solid solution of carbon in the α-iron after
"self-tempering" of martensite. 4. The final transformation of the
retained austenite in beinite with α-iron particles and cementite
formation. 5. The implementation of the diffusion mechanism of γ ⇒
α transformation.
Abstract: Micro power sources are required to be used in autonomous microelectromechanical system (MEMS). In this paper,
we designed and fabricated a three dimensional (3D) MEMS supercapacitor, which is consisting of conformal silicon
dioxide/titanium/polypyrrole (PPy) layers on silicon substrate. At first, ''through-structure'' was fabricated on the silicon substrate by high-aspect-ratio deep reactive ion etching (DRIE) method, which enlarges the available surface area significantly. Then the SiO2/Ti/PPy layers grew sequentially on the ³through-structure´. Finally, the supercapacitor was investigated by electrochemical methods.