Abstract: Drying behavior of blanched sweet potato in a cabinet
dryer using different five air temperatures (40-80°C) and ten sweet
potato varieties sliced to 5mm thickness were investigated. The
drying data were fitted to eight models. The Modified Henderson and
Pabis model gave the best fit to the experimental moisture ratio data
obtained during the drying of all the varieties while Newton (Lewis)
and Wang and Singh models gave the least fit. The values of Deff
obtained for Bophelo variety (1.27 x 10-9 to 1.77 x 10-9 m2/s) was
the least while that of S191 (1.93 x 10-9 to 2.47 x 10-9 m2/s) was the
highest which indicates that moisture diffusivity in sweet potato is
affected by the genetic factor. Activation energy values ranged from
0.27-6.54 kJ/mol. The lower activation energy indicates that drying
of sweet potato slices requires less energy and is hence a cost and
energy saving method. The drying behavior of blanched sweet potato
was investigated in a cabinet dryer. Drying time decreased
considerably with increase in hot air temperature. Out of the eight
models fitted, the Modified Henderson and Pabis model gave the best
fit to the experimental moisture ratio data on all the varieties while
Newton, Wang and Singh models gave the least. The lower activation
energy (0.27 - 6.54 kJ/mol) obtained indicates that drying of sweet
potato slices requires less energy and is hence a cost and energy
saving method.
Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value
Abstract: We introduced an all-optical multicasting
characteristics with wavelength conversion based on a novel
all-optical triode using negative feedback semiconductor optical
amplifier. This study was demonstrated with a transfer speed of 10
Gb/s to a non-return zero 231-1 pseudorandom bit sequence system.
This multi-wavelength converter device can simultaneously provide
three channels of output signal with the support of non-inverted and
inverted conversion. We studied that an all-optical multicasting and
wavelength conversion accomplishing cross gain modulation is
effective in a semiconductor optical amplifier which is effective to
provide an inverted conversion thus negative feedback. The
relationship of received power of back to back signal and output
signals with wavelength 1535 nm, 1540 nm, 1545 nm, 1550 nm, and
1555 nm with bit error rate was investigated. It was reported that the
output signal wavelengths were successfully converted and modulated
with a power penalty of less than 8.7 dB, which the highest is 8.6 dB
while the lowest is 4.4 dB. It was proved that all-optical multicasting
and wavelength conversion using an optical triode with a negative
feedback by three channels at the same time at a speed of 10 Gb/s is a
promising device for the new wavelength conversion technology.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.
Abstract: Aluminium and its alloys have excellent corrosion
resistant properties, ease of fabrication and high specific strength to
weight ratio. In this investigation an attempt has been made to study
the effect of different post weld heat treatment methods on the
mechanical and metallurgical properties of TIG welded joints of the
commercial aluminium alloy. Three different methods of post weld
heat treatments are solution heat treatment, artificial ageing and
combination of solution heat treatment and artificial aging are given
to TIG welded aluminium joints. Mechanical and metallurgical
properties of As welded joints of the aluminium alloys and post weld
heat treated joints of the aluminium alloys were examined.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: The psychological impact of peer influence on its
individual group members, can make them resist HIV/AIDS
counselling and testing. This study investigated the correlate of peer
influence and resistance to HIV/AIDS counselling and testing among
students in tertiary institutions in Kano state, Nigeria. To achieve
this, three null hypotheses were postulated and tested. Cross-
Sectional Survey Design was employed in which 1512 sample was
selected from a student population of 104,841.Simple Random
Sampling was used in the selection. A self-developed 20-item scale
called Peer Influence and Psychological Resistance Inventory
(PIPRI) was used for data collection. Pearson Product Moment
Correlation (PPMCC) via test-retest method was applied to estimate a
reliability coefficient of 0.86 for the scale. Data obtained was
analyzed using t-test and PPMCC at 0.05 level of confidence. Results
reveal 26.3% (397) of the respondents being influenced by their peer
group, while 39.8% showed resistance. Also, the t-tests and PPMCC
statistics were greater than their respective critical values. This shows
that there was a significant gender difference in peer influence and a
difference between peer influence and resistance to HIV/AIDS
counselling and testing. However, a positive relationship between
peer influence and resistance to HIV/AIDS counselling and testing
was shown. A major recommendation offered suggests the use of
reinforcement and social support for positive attitudes and
maintenance of safe behaviour among students who patronize
HIV/AIDS counselling.
Abstract: In this paper, the effect of admixtures on the tensional
strength of concrete in Urmia-lake water have been investigated. We
made different types of concretes with the ratio of w/c and replaced
different percentages of micro-silica, air-entraining, super plasticizer,
corrosion-inhibiting, and caulk with two types of cement I and II as
well as investigating in both ordinary water and Urmia-lake water.
The tensional strength was investigated on these samples.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: It’s an era of high competition, dynamism and
complexities which have forced organizations to change dramatically
due to rising customer expectations. Marketers are under constant
pressure to deliver finest to their customers. With the advent of
technology, marketers have identified latest advertising media
options to reach out to target audience. But the conventional ways of
print advertisements still holds a deeper penetration and coverage.
Various researchers and practitioners have studied the area of print
media advertising and have tried to identify and implement
advertisement effectiveness enablers. The purpose of this paper is to
suggest select enablers for print media in Indian context using an
integrated approach of review of literature and investigative
interviews with academicians and experts from the area of
advertising.
Abstract: The purpose of this study was to investigate graduate
students’ visual attention and perceptions of a Prezi presentation. Ten
postgraduate master students were presented with a Prezi presentation
at the Centre for Instructional Technology and Multimedia, Universiti
Sains Malaysia (USM). The eye movement indicators such as dwell
time, average fixation on the areas of interests, heat maps and focus
maps were abstracted to indicate the students’ visual attention.
Descriptive statistics was employed to analyze the students’
perception of the Prezi presentation in terms of text, slide design,
images, layout and overall presentation. The result revealed that the
students paid more attention to the text followed by the images and
sub heading presented through the Prezi presentation.
Abstract: The asynchronous discussion forum is one of the most
widely used activities in learning management system environment.
Online forum allows participants to interact, construct knowledge,
and can be used to complement face to face sessions in blended
learning courses. However, to what extent do the students perceive
the benefits or advantages of forum remain to be seen. Through
content and social network analyses, instructors will be able to gauge
the students’ engagement and knowledge construction level. Thus,
this study aims to analyze the students’ level of knowledge
construction and their participation level that occur through online
discussion. It also attempts to investigate the relationship between the
level of knowledge construction and their social interaction patterns.
The sample involves 23 students undertaking a master course in one
public university in Malaysia. The asynchronous discussion forum
was conducted for three weeks as part of the course requirement. The
finding indicates that the level of knowledge construction is quite
low. Also, the density value of 0.11 indicating the overall
communication among the participants in the forum is low. This
study reveals that strong and significant correlations between SNA
measures (in-degree centrality, out-degree centrality) and level of
knowledge construction. Thus, allocating these active students in
different group aids the interactive discussion takes place. Finally,
based upon the findings, some recommendations to increase students’
level of knowledge construction and also for further research are
proposed.
Abstract: Lately, asynchronous discussion forum is integrated in
higher educational institutions as it may increase learning process,
learners’ understanding, achievement and knowledge construction.
The asynchronous discussion forum is used to complement the
traditional, face-to-face learning session in hybrid learning courses.
However, studies have proven that students’ engagement in online
forums is still unconvincing. Thus, the aim of this study is to
investigate the motivating factors and obstacles that affect the
learners’ engagement in asynchronous discussion forum. This study
is carried out in one of the public higher educational institutions in
Malaysia with 18 postgraduate students as samples. The authors have
developed a 40-items questionnaire based on literature review. The
results indicate several factors that have encouraged or limited
students’ engagement in asynchronous discussion forum: (a) the
practices or behaviors of peers, or instructors, (b) the needs for the
discussions, (c) the learners’ personalities, (d) constraints in
continuing the discussion forum, (e) lack of ideas, (f) the level of
thoughts, (g) the level of knowledge construction, (h) technical
problems, (i) time constraints and (j) misunderstanding. This study
suggests some recommendations to increase the students’
engagement in online forums. Finally, based upon the findings, some
implications are proposed for further research.
Abstract: This experimental study aims at studying the
conversion of macro-algae into bioethanol under several steps of
procedure: preparation, pre-treatment, fermentation, and distillation.
The main objective of this work was to investigate the role of buffer’s
type as a stabiliser of pH level and fermentation time on the yield of
ethanol. For this purpose, experiments were carried out on biomass
macro-algae to de-couple the pre-treatment and fermentation
processes from those associated with distillation process. β-
glucosidase was used as cellulose decomposer during hydrolysis step
and yeast was used during fermentation process. The species of
macro-algae utilised as energy feedstock was Ulva lactuca and it was
harvested from southern coast of Central of Java Island – Indonesia.
Experiments were conducted in a simple fermenter over a different
buffer: citrate buffer and acetic buffer, and over a range of
fermentation times between 5 to 20 days. The ethanol production was
found to be significantly affected by both variables. The optimum
time of fermentation was 10 days with citrate buffer; result in
0.88458% of ethanol, and the ethanol content after distillation
process was shown 0.985015%.
Abstract: Fritillaria oranensis (Liliaceae) was described in 1874
by pomel from Algeria. Plant samples have been collected from the
mount of Tessala (Sidi-Bel-Abbes). The morphological features of
various organs of the plant are described in detail. In the
morphological part of the study, features of various organs of the
plants such as stem and leaf were determined and illustrated.
Ecological studies provide information about the physical and
chemical structure of soil types in Tessala Mountain. The aim of this
original investigation is to put forth ecological and anatomical
features of these species for the first time, but at the same time given
detailed account of the morphological characteristics of the stem and
leaf of Fritillaria oranensis.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.