Abstract: We develop a periodically-poled LiNbO3 (PPLN)
device for highly-efficient third-harmonic generation (THG), where
the THG efficiency is enhanced with a cavity. THG can usually be
produced via χ(3)-nonlinear materials by optical pumping with very
high pump-power. Instead, we here propose THG by moderate-power
pumping through a specially-designed PPLN device containing
only χ(2)-nonlinearity, where sum-frequency generation in the χ(2)
process is employed for the mixing of a pump beam and a
second-harmonic-generation (SHG) beam produced from the pump
beam. The cavity is designed to increase the SHG power with dichroic
mirrors attached to both ends of the device that perfectly reflect
the SHG beam back to the device and yet let the pump and THG
beams pass through the mirrors. This brings about a THG-power
enhancement because of THG power proportional to the enhanced
SHG power. We examine the THG-efficiency dependence on the
mirror reflectance and show that very high THG-efficiency is obtained
at moderate pump-power when compared with that of a cavity-free
PPLN device.
Abstract: Wireless sensor network finds role in environmental monitoring, industrial applications, surveillance applications, health monitoring and other supervisory applications. Sensing devices form the basic operational unit of the network that is self-battery powered with limited life time. Sensor node spends its limited energy for transmission, reception, routing and sensing information. Frequent energy utilization for the above mentioned process leads to network lifetime degradation. To enhance energy efficiency and network lifetime, we propose a modified energy optimization and node recovery post failure method, Energy-Link Failure Recovery Routing (E-LFRR) algorithm. In our E-LFRR algorithm, two phases namely, Monitored Transmission phase and Replaced Transmission phase are devised to combat worst case link failure conditions. In Monitored Transmission phase, the Actuator Node monitors and identifies suitable nodes for shortest path transmission. The Replaced Transmission phase dispatches the energy draining node at early stage from the active link and replaces it with the new node that has sufficient energy. Simulation results illustrate that this combined methodology reduces overhead, energy consumption, delay and maintains considerable amount of alive nodes thereby enhancing the network performance.
Abstract: The main objective of this work is to enhance the Pulsed Eddy Current (PEC) response from the aluminum structure using signal processing. Cracks and metal loss in different structures cause changes in PEC response measurements. In this paper, time-frequency analysis is used to represent PEC response, which generates a large quantity of data and reduce the noise due to measurement. Power Spectral Density (PSD) after Wavelet Decomposition (PSD-WD) is proposed for defect detection. The experimental results demonstrate that the cracks in the surface can be extracted satisfactorily by the proposed methods. The validity of the proposed method is discussed.
Abstract: A mathematical model for knowledge acquisition in
teaching and learning is proposed. In this study we adopt the
mathematical model that is normally used for disease modelling
into teaching and learning. We derive mathematical conditions which
facilitate knowledge acquisition. This study compares the effects
of dropping out of the course at early stages with later stages of
learning. The study also investigates effect of individual interaction
and learning from other sources to facilitate learning. The study fits
actual data to a general mathematical model using Matlab ODE45
and lsqnonlin to obtain a unique mathematical model that can be
used to predict knowledge acquisition. The data used in this study
was obtained from the tutorial test results for mathematics 2 students
from the Central University of Technology, Free State, South Africa
in the department of Mathematical and Physical Sciences. The study
confirms already known results that increasing dropout rates and
forgetting taught concepts reduce the population of knowledgeable
students. Increasing teaching contacts and access to other learning
materials facilitate knowledge acquisition. The effect of increasing
dropout rates is more enhanced in the later stages of learning
than earlier stages. The study opens up a new direction in further
investigations in teaching and learning using differential equations.
Abstract: In this paper a method for image dehazing is proposed in lifting wavelet transform domain. Lifting Daubechies (D4) wavelet has been used to obtain the approximate image and detail images. As the haze is contained in low frequency part, only the approximate image is used for further processing. This region is processed by dehazing algorithm based on dark channel prior (DCP). The dehazed approximate image is then recombined with the detail images using inverse lifting wavelet transform. Implementation of lifting wavelet transform has the advantage of auxiliary memory saving, fast implementation and simplicity. Also, the proposed method deals with near white scene problem, blue horizon issue and localized light sources in a way to enhance image quality and makes the algorithm robust. Simulation results present improvement in terms of visual quality, parameters such as root mean square (RMS) contrast, structural similarity index (SSIM), entropy and execution time.
Abstract: Agri-food value chain involves various stakeholders with different roles. All of them abide by national and international rules and leverage marketing strategies to advance their products. Food products and related processing phases carry with it a big mole of data that are often not used to inform final customer. Some data, if fittingly identified and used, can enhance the single company, and/or the all supply chain creates a math between marketing techniques and voluntary traceability strategies. Moreover, as of late, the world has seen buying-models’ modification: customer is careful on wellbeing and food quality. Food citizenship and food democracy was born, leveraging on transparency, sustainability and food information needs. Internet of Things (IoT) and Analytics, some of the innovative technologies of Industry 4.0, have a significant impact on market and will act as a main thrust towards a genuine ‘4.0 change’ for agriculture. But, realizing a traceability system is not simple because of the complexity of agri-food supply chain, a lot of actors involved, different business models, environmental variations impacting products and/or processes, and extraordinary climate changes. In order to give support to the company involved in a traceability path, starting from business model analysis and related business process a Framework to Manage Product Data in Agri-Food Supply Chain for Voluntary Traceability was conceived. Studying each process task and leveraging on modeling techniques lead to individuate information held by different actors during agri-food supply chain. IoT technologies for data collection and Analytics techniques for data processing supply information useful to increase the efficiency intra-company and competitiveness in the market. The whole information recovered can be shown through IT solutions and mobile application to made accessible to the company, the entire supply chain and the consumer with the view to guaranteeing transparency and quality.
Abstract: This paper discusses the current trends in medical
image registration techniques and addresses the need to provide a
solid theoretical foundation for research endeavours. Methodological
analysis and synthesis of quality literature was done, providing a
platform for developing a good foundation for research study in
this field which is crucial in understanding the existing levels of
knowledge. Research on medical image registration techniques assists
clinical and medical practitioners in diagnosis of tumours and lesion
in anatomical organs, thereby enhancing fast and accurate curative
treatment of patients. Literature review aims to provide a solid
theoretical foundation for research endeavours in image registration
techniques. Developing a solid foundation for a research study is
possible through a methodological analysis and synthesis of existing
contributions. Out of these considerations, the aim of this paper is
to enhance the scientific community’s understanding of the current
status of research in medical image registration techniques and also
communicate to them, the contribution of this research in the field of
image processing. The gaps identified in current techniques can be
closed by use of artificial neural networks that form learning systems
designed to minimise error function. The paper also suggests several
areas of future research in the image registration.
Abstract: Methanol-to-propylene conversion was carried out in a continuous-flow fixed-bed reactor over nano-sized HZSM-5 zeolites. The HZSM-5 catalysts were synthesized with different Si/Al ratio and silicon sources, and treated with NaOH. The structural property, morphology, and acidity of catalysts were measured by XRD, N2 adsorption, FE-SEM, TEM, and NH3-TPD. The results indicate that the increment of Si/Al ratio decreased the acidity of catalysts and then improved propylene selectivity, while silicon sources had slight impact on the acidity but affected the product distribution. The desilication after alkali treatment could increase intracrystalline mesopores and enhance propylene selectivity.
Abstract: This paper introduces the applicability of underwater
photogrammetric survey within challenging conditions as the main
tool to enhance and enrich the process of documenting archaeological
excavation through the creation of 4D models. Photogrammetry was
being attempted on underwater archaeological sites at least as early
as the 1970s’ and today the production of traditional 3D models is
becoming a common practice within the discipline. Photogrammetry
underwater is more often implemented to record exposed underwater
archaeological remains and less so as a dynamic interpretative tool. Therefore, it tends to be applied in bright environments and
when underwater visibility is > 1m, reducing its implementation
on most submerged archaeological sites in more turbid conditions.
Recent years have seen significant development of better digital
photographic sensors and the improvement of optical technology,
ideal for darker environments. Such developments, in tandem with
powerful processing computing systems, have allowed underwater
photogrammetry to be used by this research as a standard recording
and interpretative tool. Using multi-source photogrammetry (5,
GoPro5 Hero Black cameras) this paper presents the accumulation of
daily (4D) underwater surveys carried out in the Early Bronze Age
(3,300 BC) to Late Ottoman (17th Century AD) archaeological site of
Ropotamo in the Bulgarian Black Sea under challenging conditions
(< 0.5m visibility). It proves that underwater photogrammetry can
and should be used as one of the main recording methods even in low
light and poor underwater conditions as a way to better understand
the complexity of the underwater archaeological record.
Abstract: A numerical investigation of unsteady mixed convection heat transfer in a 3D moving top wall enclosure, which has a central rotating cylinder and uses either artificial roughness on the bottom hot plate or smooth bottom hot plate to study the heat transfer enhancement, is completed for fixed circular cylinder, and anticlockwise and clockwise rotational speeds, -1 ≤ Ω ≤ 1, at Reynolds number of 5000. The top lid-driven wall was cooled, while the other remaining walls that completed obstructed cubic were kept insulated and motionless. A standard k-ε model of Unsteady Reynolds-Averaged Navier-Stokes (URANS) method is involved to deal with turbulent flow. It has been clearly noted that artificial roughness can strongly control the thermal fields and fluid flow patterns. Ultimately, the heat transfer rate has been dramatically increased by involving artificial roughness on the heated bottom wall in the presence of rotating cylinder.
Abstract: The advancement in various concrete ingredients like plasticizers, additives and fibers, etc. has enabled concrete technologists to develop many viable varieties of special concretes in recent decades. Such various varieties of concrete have significant enhancement in green as well as hardened properties of concrete. A prudent selection of appropriate type of concrete can resolve many design and application issues in construction projects. This paper focuses on usage of self-compacting concrete, high early strength concrete, structural lightweight concrete, fiber reinforced concrete, high performance concrete and ultra-high strength concrete in the structures. The modified properties of strength at various ages, flowability, porosity, equilibrium density, flexural strength, elasticity, permeability etc. need to be carefully studied and incorporated into the design of the structures. The paper demonstrates various mixture combinations and the concrete properties that can be leveraged. The selection of such products based on the end use of structures has been proposed in order to efficiently utilize the modified characteristics of these concrete varieties. The study involves mapping the characteristics with benefits and savings for the structure from design perspective. Self-compacting concrete in the structure is characterized by high shuttering loads, better finish, and feasibility of closer reinforcement spacing. The structural design procedures can be modified to specify higher formwork strength, height of vertical members, cover reduction and increased ductility. The transverse reinforcement can be spaced at closer intervals compared to regular structural concrete. It allows structural lightweight concrete structures to be designed for reduced dead load, increased insulation properties. Member dimensions and steel requirement can be reduced proportionate to about 25 to 35 percent reduction in the dead load due to self-weight of concrete. Steel fiber reinforced concrete can be used to design grade slabs without primary reinforcement because of 70 to 100 percent higher tensile strength. The design procedures incorporate reduction in thickness and joint spacing. High performance concrete employs increase in the life of the structures by improvement in paste characteristics and durability by incorporating supplementary cementitious materials. Often, these are also designed for slower heat generation in the initial phase of hydration. The structural designer can incorporate the slow development of strength in the design and specify 56 or 90 days strength requirement. For designing high rise building structures, creep and elasticity properties of such concrete also need to be considered. Lastly, certain structures require a performance under loading conditions much earlier than final maturity of concrete. High early strength concrete has been designed to cater to a variety of usages at various ages as early as 8 to 12 hours. Therefore, an understanding of concrete performance specifications for special concrete is a definite door towards a superior structural design approach.
Abstract: The latent heat thermal energy storage system is a
thrust area of research due to exuberant thermal energy storage
potential. The thermal performance of PCM is significantly
augmented by installation of the high thermal conductivity fins. The
objective of the present study is to obtain optimum size and location
of the fins to enhance diffusion heat transfer without altering overall
melting time. Hence, the constructal theory is employed to eliminate,
resize, and re-position the fins. A numerical code based on conjugate
heat transfer coupled enthalpy porosity approached is developed to
solve Navier-Stoke and energy equation. The numerical results show
that the constructal fin design has enhanced the thermal performance
along with the increase in the overall volume of PCM when
compared to conventional. The overall volume of PCM is found to be
increased by half of total of volume of fins. The elimination and repositioning
the fins at high temperature gradient from low
temperature gradient is found to be vital.
Abstract: Deteriorating quality of the pedestrian environment
and the increasing risk of pedestrian crashes are major concerns for
most of the cities in India. The recent shift in the priority to
motorized transport and the abating condition of existing pedestrian
facilities can be considered as prime reasons for the increasing
pedestrian related crashes in India. Bengaluru City – the IT capital
hub of the nation is not much different from this. The increase in
number of pedestrian crashes in Bengaluru reflects the same. To
resolve this issue and to ensure safe, sustainable and pedestrian
friendly sidewalks, Govt. of Karnataka, India has implemented
newfangled pedestrian sidewalks popularized programme named
Tender S.U.R.E. (Specifications for Urban Road Execution) projects.
Tender SURE adopts unique urban street design guidelines where the
pedestrians are given prime preference. The present study presents an
assessment of the quality and performance of the pedestrian side walk
and the walkability index of the newly built pedestrian friendly
sidewalks. Various physical and environmental factors affecting
pedestrian safety are identified and studied in detail. The pedestrian
mobility is quantified through Pedestrian Level of Service (PLoS)
and the pedestrian walking comfort is measured by calculating the
Walkability Index (WI). It is observed that the new initiatives taken
in reference to improving pedestrian safety have succeeded in
Bengaluru by attaining a level of Service of ‘A’ and with a good WI
score.
Abstract: We report the enhancement of Raman scattering
signal by one order of magnitude using photonic nanojet (PNJ) of a
lollipop shaped dielectric microstructure (LSDM) fabricated by a
pulsed CO₂ laser. Here, the PNJ is generated by illuminating sphere
portion of the LSDM with non-resonant laser. Unlike the surface
enhanced Raman scattering (SERS) technique, this technique is
simple, and the obtained results are highly reproducible. In addition,
an efficient technique is proposed to enhance the SERS signal with
the help of high quality factor optical resonance (whispering gallery
mode) of a LSDM. From the theoretical simulations, it has been
found that at least an order of magnitude enhancement in the SERS
signal could be achieved easily using the proposed technique. We
strongly believe that this report will enable the research community
for improving the Raman scattering signals.
Abstract: Analysis of the elastic scattering of protons on 10B nuclei has been done in the framework of the optical model and single folding model at the beam energies up to 17 MeV. We could enhance the optical potential parameters using Esis88 Code, as well as SPI GENOA Code. Linear relationship between volume real potential (V0) and proton energy (Ep) has been obtained. Also, surface imaginary potential WD is proportional to the proton energy (Ep) in the range 0.400 and 17 MeV. The radiative reaction 10B(p,γ)11C has been analyzed using potential model. A comparison between 10B(p,γ)11C and 6Li(p,γ)7Be has been made. Good agreement has been found between theoretical and experimental results in the whole range of energy. The radiative resonance reaction 7Li(p,γ)8Be has been studied.
Abstract: This paper is to clarify the relationship between ICT
and income inequality. To do so, we develop the general equilibrium
model with ICT investment, obtain the equilibrium solutions, and then
simulate the model with these solutions for some OECD countries.
As a result, generally, during the corresponding periods we confirm
that the relationship between ICT investment and income inequality
is positive. In this mode, the increment of the ratio of ICT investment
to the aggregated investment in stock enhances the capital’s share of
income, and finally leads to income inequality such as the increase
of the share of the top decile income. Although we confirm the
positive relationship between ICT investment and income inequality,
the upward trend for that relationship depends on the values of
parameters for the making use of the simulations and these parameters
are not deterministic in the magnitudes on the calculated results for
the simulations.
Abstract: In northern European climates, domestic space heating and hot water represents a significant proportion of total primary total primary energy use and meeting these demands from a national electricity grid network supplied by renewable energy sources provides an opportunity for a significant reduction in EU CO2 emissions. However, in order to adapt to the intermittent nature of renewable energy generation and to avoid co-incident peak electricity usage from consumers that may exceed current capacity, the demand for heat must be decoupled from its generation. Storage of heat within the fabric of dwellings for use some hours, or days, later provides a route to complete decoupling of demand from supply and facilitates the greatly increased use of renewable energy generation into a local or national electricity network. The integration of thermal energy storage into the building fabric for retrieval at a later time requires much evaluation of the many competing thermal, physical, and practical considerations such as the profile and magnitude of heat demand, the duration of storage, charging and discharging rate, storage media, space allocation, etc. In this paper, the authors report investigations of thermal storage in building fabric using concrete material and present an evaluation of several factors that impact upon performance including heating pipe layout, heating fluid flow velocity, storage geometry, thermo-physical material properties, and also present an investigation of alternative storage materials and alternative heat transfer fluids. Reducing the heating pipe spacing from 200 mm to 100 mm enhances the stored energy by 25% and high-performance Vacuum Insulation results in heat loss flux of less than 3 W/m2, compared to 22 W/m2 for the more conventional EPS insulation. Dense concrete achieved the greatest storage capacity, relative to medium and light-weight alternatives, although a material thickness of 100 mm required more than 5 hours to charge fully. Layers of 25 mm and 50 mm thickness can be charged in 2 hours, or less, facilitating a fast response that could, aggregated across multiple dwellings, provide significant and valuable reduction in demand from grid-generated electricity in expected periods of high demand and potentially eliminate the need for additional new generating capacity from conventional sources such as gas, coal, or nuclear.
Abstract: Heat transfer enhancement objects like extended surfaces, fins etc. are chosen for their thermal performance as well as for other design parameters depending on various applications. The present paper is on experimental study to investigate the heat transfer enhancement through wire mesh fin arrays equipped with horizontal base plate. The data used in performance analysis were obtained experimentally for the material (mild steel) for different heat inputs such as 40, 60, 80, 100 and 120 watt, by varying wire mesh diameter, fin height and spacing between two fin arrays. Using the Taguchi experimental design method, optimum design parameters and their levels were investigated. Average heat transfer coefficient was considered as a performance characteristic parameter. An L9 (33) orthogonal array was selected as an experimental plan. Optimum results were found by experimenting. It is observed that the wire mesh diameter and fin height have a higher impact on heat transfer coefficient as compared to spacing between two fin arrays.
Abstract: In any production process, every product is aimed to attain a certain standard, but the presence of assignable cause of variability affects our process, thereby leading to low quality of product. The ability to identify and remove this type of variability reduces its overall effect, thereby improving the quality of the product. In case of a univariate control chart signal, it is easy to detect the problem and give a solution since it is related to a single quality characteristic. However, the problems involved in the use of multivariate control chart are the violation of multivariate normal assumption and the difficulty in identifying the quality characteristic(s) that resulted in the out of control signals. The purpose of this paper is to examine the use of non-parametric control chart (the bootstrap approach) for obtaining control limit to overcome the problem of multivariate distributional assumption and the p-value method for detecting out of control signals. Results from a performance study show that the proposed bootstrap method enables the setting of control limit that can enhance the detection of out of control signals when compared, while the p-value method also enhanced in identifying out of control variables.
Abstract: The economic growth of any nation is steered and dependent on innovation in technology. It can be preferably argued that technology has enhanced the quality of life. Technology is linked both with an economic and a social structure. But there are some parts of the world or communities which are yet to reap the benefits of technological innovation. Business and organizations are now well equipped with cutting-edge innovations that improve the firm performance and provide them with a competitive edge, but rarely does it have a positive impact on any community which is weak and marginalized. In recent times, it is observed that communities are actively handling social or ecological issues with the help of indigenous technologies. Thus, "Appropriate Technology" comes into the discussion, which is quite prevalent in the rural third world. Appropriate technology grew as a movement in the mid-1970s during the energy crisis, but it lost its stance in the following years when people started it to describe it as an inferior technology or dead technology. Basically, there is no such technology which is inferior or sophisticated for a particular region. The relevance of appropriate technology lies in penetrating technology into a larger and weaker section of community where the “Bottom of the pyramid” can pay for technology if they find the price is affordable. This is a theoretical paper which primarily revolves around how appropriate technology has faded and again evolved in both developed and developing countries. The paper will try to focus on the various concepts, history and challenges faced by the appropriate technology over the years. Appropriate technology follows a documented approach but lags in overall design and diffusion. Diffusion of technology into the poorer sections of community remains unanswered until the present time. Appropriate technology is multi-disciplinary in nature; therefore, this openness allows having a varied working model for different problems. Appropriate technology is a friendly technology that seeks to improve the lives of people in a constraint environment by providing an affordable and sustainable solution. Appropriate technology needs to be defined in the era of modern technological advancement for sustainability.