Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.
Abstract: Recent developments in Soft computing techniques,
power electronic switches and low-cost computational hardware have
made it possible to design and implement sophisticated control
strategies for sensorless speed control of AC motor drives. Such an
attempt has been made in this work, for Sensorless Speed Control of
Induction Motor (IM) by means of Direct Torque Fuzzy Control
(DTFC), PI-type fuzzy speed regulator and MRAS speed estimator
strategy, which is absolutely nonlinear in its nature. Direct torque
control is known to produce quick and robust response in AC drive
system. However, during steady state, torque, flux and current ripple
occurs. So, the performance of conventional DTC with PI speed
regulator can be improved by implementing fuzzy logic techniques.
Certain important issues in design including the space vector
modulated (SVM) 3-Ф voltage source inverter, DTFC design,
generation of reference torque using PI-type fuzzy speed regulator
and sensor less speed estimator have been resolved. The proposed
scheme is validated through extensive numerical simulations on
MATLAB. The simulated results indicate the sensor less speed
control of IM with DTFC and PI-type fuzzy speed regulator provides
satisfactory high dynamic and static performance compare to
conventional DTC with PI speed regulator.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: This paper deals principally with the socio-economic impact on the local Iban community in Mukah Division, Sarawak; with the commencement of the open-cut coal mining industry since 2003. To-date there are no actual studies being carried out by either the public or private sector to truly analyze how the Iban community is coping with the advent of a large influx of cash into their society. The Iban community has traditionally been practicing shifting cultivation and farming of domesticated animals; with a portion of the younger generation working as laborers and professional. This paper represents the views and observations of the author supported by some statistical facts extracted from published articles and non-published reports. The paper deals primarily in the following areas: • Background of the coal mining industry in Mukah Division, Sarawak; • Benefits of the coal mining industry towards the Iban community; • Issues / Problems arise in the Iban community because of the presence of the coal mining industry; and • Possible actions that need to be taken to overcome these issues/ problems.
Abstract: This paper focuses on developing an integrated
reliable and sophisticated model for ultra large wind turbines And to
study the performance and analysis of vector control on large wind
turbines. With the advance of power electronics technology, direct
driven multi-pole radial flux PMSG (Permanent Magnet Synchronous
Generator) has proven to be a good choice for wind turbines
manufacturers. To study the wind energy conversion systems, it is
important to develop a wind turbine simulator that is able to produce
realistic and validated conditions that occur in real ultra MW wind
turbines. Three different packages are used to simulate this model,
namely, Turbsim, FAST and Simulink. Turbsim is a Full field wind
simulator developed by National Renewable Energy Laboratory
(NREL). The wind turbine mechanical parts are modeled by FAST
(Fatigue, Aerodynamics, Structures and Turbulence) code which is
also developed by NREL. Simulink is used to model the PMSG, full
scale back to back IGBT converters, and the grid.
Abstract: This paper presents the development of a hybrid
thermal model for the EVO Electric AFM 140 Axial Flux Permanent
Magnet (AFPM) machine as used in hybrid and electric vehicles. The
adopted approach is based on a hybrid lumped parameter and finite
difference method. The proposed method divides each motor
component into regular elements which are connected together in a
thermal resistance network representing all the physical connections
in all three dimensions. The element shape and size are chosen
according to the component geometry to ensure consistency. The
fluid domain is lumped into one region with averaged heat transfer
parameters connecting it to the solid domain. Some model parameters
are obtained from Computation Fluid Dynamic (CFD) simulation and
empirical data. The hybrid thermal model is described by a set of
coupled linear first order differential equations which is discretised
and solved iteratively to obtain the temperature profile. The
computation involved is low and thus the model is suitable for
transient temperature predictions. The maximum error in temperature
prediction is 3.4% and the mean error is consistently lower than the
mean error due to uncertainty in measurements. The details of the
model development, temperature predictions and suggestions for
design improvements are presented in this paper.
Abstract: The present study examines the adsorption of phenol, 3-nitrophenol and dyes (methylene blue, alizarine yellow), from aqueous solutions onto a commercial activated carbon. Two different operations, semi-batch and continuous with reflux, were applied. The commercial activated carbon exhibits high adsorption abilities for phenol, 3-nitrophenol and dyes (methylene blue and alizarin yellow) from their aqueous solutions. The adsorption of all adsorbates after 1 h is higher by the continuous operation with reflux than by the semibatch operation. The adsorption of phenol is higher than that of 3-nitrophenol for both operations. Similarly, the adsorption of alizarin yellow is higher than that of methylene blue for both operations. The regenerated commercial activated carbon regains its adsorption ability due to the removal of the adsorbate from its pores during the regeneration.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: One of the potential and effective ways of
storing thermal energy in buildings is the integration of brick with phase change materials (PCMs). This paper presents a two-dimensional model for simulating and analyzing of PCM
in order to minimize energy consumption in the buildings. The numerical approach has been used with the real weather data of a selected city of Iran (Tehran). Two kinds of brick integrated PCM are investigated and compared base on
outdoor weather conditions and the amount of energy
consumption. The results show a significant reduction in
maximum entering heat flux to building about 32.8%
depending on PCM quantity. The results are analyzed by
various temperature contour plots. The contour plots
illustrated the time dependent mechanism of entering heat flux for a brick integrated with PCM. Further analysis is developed to investigate the effect of PCM location on the inlet heat flux. The results demonstrated that to achieve maximum performance of PCM it is better to locate PCM near the outdoor.
Abstract: It is well known that surface enhancements play an important role in augmenting the thermal performance of flat plate solar collector. In this paper, an attempt is made to explain in a comparative way the effect of surface geometry of solar collector having dimple geometry with that of a flat plate solar collector of the same size. A CFD analysis was carried out for the two cases, subjected to a constant heat flux of 600W/m2 and 1000W/m2. It can be inferred from the study that the absorber plate temperature shows a rise of average surface temperature of about 50C for the dimple solar collector when compared to a flat plate solar collector. Most importantly, the average exit water temperature shows a marked improvement of about 5.50C for a dimple solar collector as compared to that of a flat plate solar collector.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: Induction machine models used for steady-state and
transient analysis require machine parameters that are usually
considered design parameters or data. The knowledge of induction
machine parameters is very important for Indirect Field Oriented
Control (IFOC). A mismatched set of parameters will degrade the
response of speed and torque control. This paper presents an
improvement approach on rotor time constant adaptation in IFOC for
Induction Machines (IM). Our approach tends to improve the
estimation accuracy of the fundamental model for flux estimation.
Based on the reduced order of the IM model, the rotor fluxes and
rotor time constant are estimated using only the stator currents and
voltages. This reduced order model offers many advantages for real
time identification parameters of the IM.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: Experiments were conducted to characterize fire
properties of wood exposed to the certain external heat flux and
under variety of wood moisture content. Six kinds of Indonesian
wood: keruing, sono, cemara, kamper, pinus, and mahoni were
exposed to radiant heat from a conical heater, result in appearance of
a stable flame on the wood surface caused by spontaneous ignition. A
thermocouple K-type was used to measure the wood surface
temperature. Temperature histories were recorded throughout each
experiment at 1 s intervals using a TC-08. Data of first ignition time
and temperature, end ignition time and temperature, and charring rate
have been successfully collected. It was found that the ignition
temperature and charring rate depend on moisture content of wood.
Abstract: Vacuum membrane distillation (VMD) process can be
used for water purification or the desalination of salt water. The
process simply consists of a flat sheet hydrophobic micro porous
PTFE membrane and diaphragm vacuum pump without a condenser
for the water recovery or trap. The feed was used aqueous NaCl
solution. The VMD experiments were performed to evaluate the heat
and mass transfer coefficient of the boundary layer in a membrane
module. The only operating parameters are feed inlet temperature,
and feed flow rate were investigated. The permeate flux was strongly
affected by the feed inlet temperature, feed flow rate, and boundary
layer heat transfer coefficient. Since lowering the temperature
polarization coefficient is essential enhance the process performance
considerable and maximizing the heat transfer coefficient for
maximizes the mass flux of distillate water. In this paper, the results
of VMD experiments are used to measure the boundary layer heat
transfer coefficient, and the experimental results are used to reevaluate
the empirical constants in the Dittus- Boelter equation.
Abstract: Towards the end of 19th century, the discovery of tin
and the growing importance of rubber, had led Malaya to once again
become the centre of attraction to western colonization, which later
on caused the region to be influxed by cheap labour from China and
India. One of the factors which attracted the alien communities was
the characteristics of social relation offered by the Malays. If one
analyzes the history of social relation of the Malays either among
themselves or their relation with alien communities, it is apparent that
the community places high regards to values such as tolerant,
cooperative, respectful and helpful with each other. In fact, all these
values are deeply rooted in the value of 'budi'. With the arrival of
Islam, the value of 'budi' had been well assimilated with Islamic
values thus giving birth to the value of 'budi-Islam'. Through 'budi-
Islam', the Malay conducted their dealings with British as well the
other communities during the time of peace or conflict. This value is
well nurtured due to the geographical circumstances like the fertile,
naturally rich land and bountiful marine life. Besides, a set of Malay
customs known as 'adat' custom contributed in enhancing the values
of budi.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: Numerical investigation of the characteristics of an 80°
delta wing in combined force-pitch and free-roll is presented. The
implicit, upwind, flux-difference splitting, finite volume scheme and
the second-order-accurate finite difference scheme are employed to
solve the flow governing equations and Euler rigid-body dynamics
equations, respectively. The characteristics of the delta wing in
combined free-roll and large amplitude force-pitch is obtained
numerically and shows a well agreement with experimental data
qualitatively. The motion in combined force-pitch and free-roll
significantly reduces the lift force and transverse stabilities of the delta
wing, which is closely related to the flying safety. Investigations on
sensitive factors indicate that the roll-axis moment of inertia and the
structural damping have great influence on the frequency and
amplitude, respectively. Moreover, the turbulence model is considered
as an influencing factor in the investigation.