Abstract: Much time series data is generally from continuous dynamic system. Firstly, this paper studies the detection of the nonlinearity of time series from continuous dynamics systems by applying the Phase-randomized surrogate algorithm. Then, the Delay Vector Variance (DVV) method is introduced into nonlinearity test. The results show that under the different sampling conditions, the opposite detection of nonlinearity is obtained via using traditional test statistics methods, which include the third-order autocovariance and the asymmetry due to time reversal. Whereas the DVV method can perform well on determining nonlinear of Lorenz signal. It indicates that the proposed method can describe the continuous dynamics signal effectively.
Abstract: It is observed that the Weighted least-square (WLS)
technique, including the modifications, results in equiripple error
curve. The resultant error as a percent of the ideal value is highly
non-uniformly distributed over the range of frequencies for which the
differentiator is designed. The present paper proposes a modification
to the technique so that the optimization procedure results in lower
maximum relative error compared to the ideal values. Simulation
results for first order as well as higher order differentiators are given
to illustrate the excellent performance of the proposed method.
Abstract: This was the first document revealing the
investigation of protein hydrolysate production optimization from J.
curcas cake. Proximate analysis of raw material showed 18.98%
protein, 5.31% ash, 8.52% moisture and 12.18% lipid. The
appropriate protein hydrolysate production process began with
grinding the J. curcas cake into small pieces. Then it was suspended
in 2.5% sodium hydroxide solution with ratio between solution/ J.
curcas cake at 80:1 (v/w). The hydrolysis reaction was controlled at
temperature 50 °C in water bath for 45 minutes. After that, the
supernatant (protein hydrolysate) was separated using centrifuge at
8000g for 30 minutes. The maximum yield of resulting protein
hydrolysate was 73.27 % with 7.34% moisture, 71.69% total protein,
7.12% lipid, 2.49% ash. The product was also capable of well
dissolving in water.
Abstract: This paper presents a NDT by infrared thermography with excitation CO2 Laser, wavelength of 10.6 μm. This excitation is the controllable heating beam, confirmed by a preliminary test on a wooden plate 1.2 m x 0.9 m x 1 cm. As the first practice, this method is applied to detecting the defect in CFRP heated by the Laser 300 W during 40 s. Two samples 40 cm x 40 cm x 4.5 cm are prepared, one with defect, another one without defect. The laser beam passes through the lens of a deviation device, and heats the samples placed at a determinate position and area. As a result, the absence of adhesive can be detected. This method displays prominently its application as NDT with the composite materials. This work gives a good perspective to characterize the laser beam, which is very useful for the next detection campaigns.
Abstract: In this paper we present a noise reduction filter for video processing. It is based on the recently proposed two dimensional steering kernel, extended to three dimensions and further augmented to suit the spatial-temporal domain of video processing. Two alternative filters are proposed - the time symmetric kernel and the time asymmetric kernel. The first reduces the noise on single sequences, but to handle the problems at scene shift the asymmetric kernel is introduced. The performance of both are tested on simulated data and on a real video sequence together with the existing steering kernel. The proposed kernels improves the Rooted Mean Squared Error (RMSE) compared to the original steering kernel method on video material.
Abstract: Since the late 1980s, the new phenomena of 'employment subcentres' or 'polycentricity' has appeared in the metropolises of North American and Western Europe and it has been an interesting topic for academics and researchers. This paper specifically uses one case study-Guangzhou to explore the development and the mechanism of employment subcentres and polycentricity in Chinese metropolises by spatial analysis method on the basis of the first economic census data. In conclusion, the paper regards that the employment subcentres and polycentricity has existed in Chinese metropolises. And that, the mechanism of them is mainly from the secondary industry instead of the tertiary industry in North American and Western Europe
Abstract: In this study, aerobic digestion of tannery industry
wastewater was carried out using mixed culture obtained from
common effluent treatment plant treating tannery wastewater. The
effect of pH, temperature, inoculum concentration, agitation speed
and initial substrate concentration on the reduction of organic matters
were found. The optimum conditions for COD reduction was found
to be pH - 7 (60%), temperature - 30ÔùªC (61%), inoculum
concentration - 2% (61%), agitation speed - 150rpm (65%) and initial
substrate concentration - 1560 mg COD/L (74%). Kinetics studies
were carried by using Monod model, First order, Diffusional model
and Singh model. From the results it was found that the Monod
model suits well for the degradation of tannery wastewater using
mixed microbial consortium.
Abstract: The recent global financial problem urges government
to play role in stimulating the economy due to the fact that private
sector has little ability to purchase during the recession. A concerned
question is whether the increased government spending crowds out
private consumption and whether it helps stimulate the economy. If
the government spending policy is effective; the private consumption
is expected to increase and can compensate the recent extra
government expense. In this study, the government spending is
categorized into government consumption spending and government
capital spending. The study firstly examines consumer consumption
along the line with the demand function in microeconomic theory.
Three categories of private consumption are used in the study. Those
are food consumption, non food consumption, and services
consumption. The dynamic Almost Ideal Demand System of the three
categories of the private consumption is estimated using the Vector
Error Correction Mechanism model. The estimated model indicates
the substituting effects (negative impacts) of the government
consumption spending on budget shares of private non food
consumption and of the government capital spending on budget share
of private food consumption, respectively. Nevertheless the result
does not necessarily indicate whether the negative effects of changes
in the budget shares of the non food and the food consumption means
fallen total private consumption. Microeconomic consumer demand
analysis clearly indicates changes in component structure of
aggregate expenditure in the economy as a result of the government
spending policy. The macroeconomic concept of aggregate demand
comprising consumption, investment, government spending (the
government consumption spending and the government capital
spending), export, and import are used to estimate for their
relationship using the Vector Error Correction Mechanism model.
The macroeconomic study found no effect of the government capital
spending on either the private consumption or the growth of GDP
while the government consumption spending has negative effect on
the growth of GDP. Therefore no crowding out effect of the
government spending is found on the private consumption but it is
ineffective and even inefficient expenditure as found reducing growth
of the GDP in the context of Thailand.
Abstract: The purpose of the study is to determine the primary mathematics student teachers- views related to use instructional technology tools in course of the learning process and to reveal how the sample presentations towards different mathematical concepts affect their views. This is a qualitative study involving twelve mathematics students from a public university. The data gathered from two semi-structural interviews. The first one was realized in the beginning of the study. After that the representations prepared by the researchers were showed to the participants. These representations contain animations, Geometer-s Sketchpad activities, video-clips, spreadsheets, and power-point presentations. The last interview was realized at the end of these representations. The data from the interviews and content analyses were transcribed and read and reread to explore the major themes. Findings revealed that the views of the students changed in this process and they believed that the instructional technology tools should be used in their classroom.
Abstract: The main objective of this project is to build an
autonomous microcontroller-based mobile robot for a local robot
soccer competition. The black competition field is equipped with
white lines to serve as the guidance path for competing robots. Two
prototypes of soccer robot embedded with the Basic Stamp II
microcontroller have been developed. Two servo motors are used as
the drive train for the first prototype whereas the second prototype
uses two DC motors as its drive train. To sense the lines, lightdependent
resistors (LDRs) supply the analog inputs for the
microcontroller. The performances of both prototypes are evaluated.
The DC motor-driven robot has produced better trajectory control
over the one using servo motors and has brought the team into the
final round.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: Electrocardiogram (ECG) segmentation is necessary
to help reduce the time consuming task of manually annotating
ECG-s. Several algorithms have been developed to segment the ECG
automatically. We first review several of such methods, and then
present a new single lead segmentation method based on Adaptive
piecewise constant approximation (APCA) and Piecewise derivative
dynamic time warping (PDDTW). The results are tested on the QT
database. We compared our results to Laguna-s two lead method. Our
proposed approach has a comparable mean error, but yields a slightly
higher standard deviation than Laguna-s method.
Abstract: Dispersions of casein micelles (CM) were studied at a
constant protein concentration of 5 wt % in high NaCl environment
ranging from 0% to 12% by Dynamic light scattering (DLS) and
Fourier Transform Infrared (FTIR). The rehydration profiles obtained
were interpreted in term of wetting, swelling and dispersion stages by
using a turbidity method. Two behaviours were observed depending
on the salt concentration. The first behaviour (low salt concentration)
presents a typical rehydration profile with a significant change
between 3 and 6% NaCl indicating quick wetting, swelling and long
dispersion stage. On the opposite, the dispersion stage of the second
behaviour (high salt concentration) was significantly shortened
indicating a strong modification of the protein backbone. A salt
increase result to a destabilization of the micelle and the formation of
mini-micelles more or less aggregated indicating an average micelles
size ranging from 100 to 200 nm. For the first time, the estimations
of secondary structural elements (irregular, ß-sheet, α-helix and turn)
by the Amide III assignments were correlated with results from
Amide I.
Abstract: Nowadays, hand vein recognition has attracted more attentions in identification biometrics systems. Generally, hand vein image is acquired with low contrast and irregular illumination. Accordingly, if you have a good preprocessing of hand vein image, we can easy extracted the feature extraction even with simple binarization. In this paper, a proposed approach is processed to improve the quality of hand vein image. First, a brief survey on existing methods of enhancement is investigated. Then a Radon Like features method is applied to preprocessing hand vein image. Finally, experiments results show that the proposed method give the better effective and reliable in improving hand vein images.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.
Abstract: The effect of teaching method on learning
assistance Dunn Review .The study, to compare the effects of
collaboration on teaching mathematics learning courses, including
writing, science, experimental girl students by other methods of
teaching basic first paid and the amount of learning students
methods have been trained to cooperate with other students with
other traditional methods have been trained to compare. The
survey on 100 students in Tehran that using random sampling ¬
cluster of girl students between the first primary selections was
performed. Considering the topic of semi-experimental research
methods used to practice the necessary information by
questionnaire, examination questions by the researcher, in
collaboration with teachers and view authority in this field and
related courses that teach these must have been collected.
Research samples to test and control groups were divided.
Experimental group and control group collaboration using
traditional methods of mathematics courses, including writing and
experimental sciences were trained. Research results using
statistical methods T is obtained in two independent groups show
that, through training assistance will lead to positive results and
student learning in comparison with traditional methods, will
increase also led to collaboration methods increase skills to solve
math lesson practice, better understanding and increased skill
level of students in practical lessons such as science and has been
writing.
Abstract: Bode stability analysis based on transmission line
modeling (TLM) for single wall carbon nanotube (SWCNT)
interconnects used in 3D-VLSI circuits is investigated for the first
time. In this analysis, the dependence of the degree of relative
stability for SWCNT interconnects on the geometry of each tube has
been acquired. It is shown that, increasing the length and diameter of
each tube, SWCNT interconnects become more stable.
Abstract: Grey mold on grape is caused by the fungus Botrytis
cinerea Pers. Trichodex WP, a new biofungicide, that contains fungal
spores of Trichoderma harzianum Rifai, was used for biological
control of Grey mold on grape. The efficacy of Trichodex WP has
been reported from many experiments. Experiments were carried out
in the locality – Banatski Karlovac, on grapevine species – talijanski
rizling. The trials were set according to instructions of methods
PP1/152(2) and PP1/17(3) , according to a fully randomized block
design. Phytotoxicity was estimated by PP methods 1/135(2), the
intensity of infection according to Towsend Heuberger , the
efficiency by Abbott, the analysis of variance with Duncan test and
PP/181(2). Application of Trichodex WP is limited to the first two
treatments. Other treatments are performed with the fungicides based
on a.i. procymidone, vinclozoline and iprodione.
Abstract: In this paper usefulness of quasi-Newton iteration
procedure in parameters estimation of the conditional variance
equation within BHHH algorithm is presented. Analytical solution of
maximization of the likelihood function using first and second
derivatives is too complex when the variance is time-varying. The
advantage of BHHH algorithm in comparison to the other
optimization algorithms is that requires no third derivatives with
assured convergence. To simplify optimization procedure BHHH
algorithm uses the approximation of the matrix of second derivatives
according to information identity. However, parameters estimation in
a/symmetric GARCH(1,1) model assuming normal distribution of
returns is not that simple, i.e. it is difficult to solve it analytically.
Maximum of the likelihood function can be founded by iteration
procedure until no further increase can be found. Because the
solutions of the numerical optimization are very sensitive to the
initial values, GARCH(1,1) model starting parameters are defined.
The number of iterations can be reduced using starting values close
to the global maximum. Optimization procedure will be illustrated in
framework of modeling volatility on daily basis of the most liquid
stocks on Croatian capital market: Podravka stocks (food industry),
Petrokemija stocks (fertilizer industry) and Ericsson Nikola Tesla
stocks (information-s-communications industry).