Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: A new code for spectral-amplitude coding optical
code-division multiple-access system is proposed called Random
diagonal (RD) code. This code is constructed using code segment and
data segment. One of the important properties of this code is that the
cross correlation at data segment is always zero, which means that
Phase Intensity Induced Noise (PIIN) is reduced. For the performance
analysis, the effects of phase-induced intensity noise, shot noise, and
thermal noise are considered simultaneously. Bit-error rate (BER)
performance is compared with Hadamard and Modified Frequency
Hopping (MFH) codes. It is shown that the system using this new
code matrices not only suppress PIIN, but also allows larger number
of active users compare with other codes. Simulation results shown
that using point to point transmission with three encoded channels,
RD code has better BER performance than other codes, also its found
that at 0 dbm PIIN noise are 10-10 and 10-11 for RD and MFH
respectively.
Abstract: A parallel block method based on Backward
Differentiation Formulas (BDF) is developed for the parallel solution
of stiff Ordinary Differential Equations (ODEs). Most common
methods for solving stiff systems of ODEs are based on implicit
formulae and solved using Newton iteration which requires repeated
solution of systems of linear equations with coefficient matrix, I -
hβJ . Here, J is the Jacobian matrix of the problem. In this paper,
the matrix operations is paralleled in order to reduce the cost of the
iterations. Numerical results are given to compare the speedup and
efficiency of parallel algorithm and that of sequential algorithm.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: Improvement in CAE methods has an important role for shortening of the vehicle product development time. It is provided that validation of the design and improvements in terms of durability can be done without hardware prototype production. In recent years, several different methods have been developed in order to investigate fatigue damage of the vehicle. The intended goal among these methods is prediction of fatigue damage in a short time with reduced costs. This study developed a new fatigue damage prediction method in the automotive sector using power spectrum densities of accelerations. This study also confirmed that the weak region in vehicle can be easily detected with the method developed in this study which results were compared with conventional method.
Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: In mobile environments, unspecified numbers of transactions
arrive in continuous streams. To prove correctness of their
concurrent execution a method of modelling an infinite number of
transactions is needed. Standard database techniques model fixed
finite schedules of transactions. Lately, techniques based on temporal
logic have been proposed as suitable for modelling infinite schedules.
The drawback of these techniques is that proving the basic
serializability correctness condition is impractical, as encoding (the
absence of) conflict cyclicity within large sets of transactions results
in prohibitively large temporal logic formulae. In this paper, we show
that, under certain common assumptions on the graph structure of
data items accessed by the transactions, conflict cyclicity need only
be checked within all possible pairs of transactions. This results in
formulae of considerably reduced size in any temporal-logic-based
approach to proving serializability, and scales to arbitrary numbers
of transactions.
Abstract: The condition of lightning surge causes the traveling waves and the temporary increase in voltage in the transmission line system. Lightning is the most harmful for destroying the transmission line and setting devices so it is necessary to study and analyze the temporary increase in voltage for designing and setting the surge arrester. This analysis describes the figure of the lightning wave in transmission line with 115 kV voltage level in Thailand by using ATP/EMTP program to create the model of the transmission line and lightning surge. Because of the limit of this program, it must be calculated for the geometry of the transmission line and surge parameter and calculation in the manual book for the closest value of the parameter. On the other hand, for the effects on surge protector when the lightning comes, the surge arrester model must be right and standardized as metropolitan electrical authority's standard. The candidate compared the real information to the result from calculation, also. The results of the analysis show that the temporary increase in voltage value will be rise to 326.59 kV at the line which is done by lightning when the surge arrester is not set in the system. On the other hand, the temporary increase in voltage value will be 182.83 kV at the line which is done by lightning when the surge arrester is set in the system and the period of the traveling wave is reduced, also. The distance for setting the surge arrester must be as near to the transformer as possible. Moreover, it is necessary to know the right distance for setting the surge arrester and the size of the surge arrester for preventing the temporary increase in voltage, effectively.
Abstract: For higher order multiplications, a huge number of
adders or compressors are to be used to perform the partial product
addition. We have reduced the number of adders by introducing
special kind of adders that are capable to add five/six/seven bits per
decade. These adders are called compressors. Binary counter
property has been merged with the compressor property to develop
high order compressors. Uses of these compressors permit the
reduction of the vertical critical paths. A 16×16 bit multiplier has
been developed using these compressors. These compressors make
the multipliers faster as compared to the conventional design that
have been used 4-2 compressors and 3-2 compressors.
Abstract: Several trillion cigarettes produced worldwide annually lead to many thousands of kilograms of toxic waste. Cigarette butts (CBs) accumulate in the environment due to the poor biodegradability of the cellulose acetate filters. This paper presents some of the results from a continuing study on recycling CBs into fired clay bricks. Physico-mechanical properties of fired clay bricks manufactured with different percentages of CBs are reported and discussed. The results show that the density of fired bricks was reduced by up to 30 %, depending on the percentage of CBs incorporated into the raw materials. Similarly, the compressive strength of bricks tested decreased according to the percentage of CBs included in the mix. The thermal conductivity performance of bricks was improved by 51 and 58 % for 5 and 10 % CBs content respectively. Leaching tests were carried out to investigate the levels of possible leachates of heavy metals from the manufactured clay-CB bricks. The results revealed trace amounts of heavy metals.
Abstract: Failure modes and effects analysis (FMEA) is an effective technique for preventing potential problems and actions needed to error cause removal. On the other hand, the oil producing companies paly a critical role in the oil industry of Iran as a developing country out of which, Sepahan Oil Co. has a considerable contribution. The aim of this research is to show how FMEA could be applied and improve the quality of products at Sepahan Oil Co. For this purpose, the four liter production line of the company has been selected for investigation. The findings imply that the application of FMEA has reduced the scraps from 50000 ppm to 5000 ppm and has resulted in a 0.92 percent decrease of the oil waste.
Abstract: A hardware efficient, multi mode, re-configurable
architecture of interleaver/de-interleaver for multiple standards,
like DVB, WiMAX and WLAN is presented. The interleavers
consume a large part of silicon area when implemented by using
conventional methods as they use memories to store permutation
patterns. In addition, different types of interleavers in different
standards cannot share the hardware due to different construction
methodologies. The novelty of the work presented in this paper is
threefold: 1) Mapping of vital types of interleavers including
convolutional interleaver onto a single architecture with flexibility
to change interleaver size; 2) Hardware complexity for channel
interleaving in WiMAX is reduced by using 2-D realization of the
interleaver functions; and 3) Silicon cost overheads reduced by
avoiding the use of small memories. The proposed architecture
consumes 0.18mm2 silicon area for 0.12μm process and can
operate at a frequency of 140 MHz. The reduced complexity helps
in minimizing the memory utilization, and at the same time
provides strong support to on-the-fly computation of permutation
patterns.
Abstract: With the fast evolution of digital data exchange, security information becomes much important in data storage and transmission. Due to the increasing use of images in industrial process, it is essential to protect the confidential image data from unauthorized access. In this paper, we analyze the Advanced Encryption Standard (AES), and we add a key stream generator (A5/1, W7) to AES to ensure improving the encryption performance; mainly for images characterised by reduced entropy. The implementation of both techniques has been realized for experimental purposes. Detailed results in terms of security analysis and implementation are given. Comparative study with traditional encryption algorithms is shown the superiority of the modified algorithm.
Abstract: In wireless sensor networks,the mobile agent technology is used in data fusion. According to the node residual energy and the results of partial integration,we design the node clustering algorithm. Optimization of mobile agent in the routing within the cluster strategy for wireless sensor networks to further reduce the amount of data transfer. Through the experiments, using mobile agents in the integration process within the cluster can be reduced the path loss in some extent.
Abstract: This paper investigates the application of large scale (LS-PV) two-axis tracking photovoltaic power plant in Al-Jagbob, Libya. A 50MW PV-grid connected (two-axis tracking) power plant design in Al-Jagbob, Libya has been carried out presently. A hetero-junction with intrinsic thin layer (HIT) type PV module has been selected and modeled. A Microsoft Excel-VBA program has been constructed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency for this system, for tracking system. The results for energy production show that the total energy output is 128.5 GWh/year. The average module efficiency is 16.6%. The electricity generation capacity factor (CF) and solar capacity factor (SCF) were found to be 29.3% and 70.4% respectively. A 50MW two axis tracking power plant with a total energy output of 128.5 GWh/year would reduce CO2 pollution by 85,581 tonnes of each year. The payback time for the proposed LS-PV photovoltaic power plant was found to be 4 years.
Abstract: The greenhouse effect and limitations on carbon
dioxide emissions concern engine maker and the future of the
internal combustion engines should go toward substantially and
improved thermal efficiency engine. Homogeneous charge
compression ignition (HCCI) is an alternative high-efficiency
technology for combustion engines to reduce exhaust emissions and
fuel consumption. However, there are still tough challenges in the
successful operation of HCCI engines, such as controlling the
combustion phasing, extending the operating range, and high
unburned hydrocarbon and CO emissions. HCCI and the exploitation
of ethanol as an alternative fuel is one way to explore new frontiers
of internal combustion engines with an eye towards maintaining its
sustainability. This study was done to extend database knowledge
about HCCI with ethanol a fuel.
Abstract: The computer has become an essential tool in modern
life, and the combined use of a computer with a projector is very
common in teaching and presentations. However, as typical computer
operating devices involve a mouse or keyboard, when making
presentations, users often need to stay near the computer to execute
functions such as changing pages, writing, and drawing, thus, making
the operation time-consuming, and reducing interactions with the
audience. This paper proposes a laser pointer interaction system able
to simulate mouse functions in order that users need not remain near
the computer, but can directly use laser pointer operations from at a
distance. It can effectively reduce the users- time spent by the
computer, allowing for greater interactions with the audience.
Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: In this paper a modification on Levenberg-Marquardt algorithm for MLP neural network learning is proposed. The proposed algorithm has good convergence. This method reduces the amount of oscillation in learning procedure. An example is given to show usefulness of this method. Finally a simulation verifies the results of proposed method.